Search Documents

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By H. B. Salisbury

The Bureau of Mines conducted research to determine if low-grade California chromite ores could be beneficiated to produce products suitable for commercial use. This research is part of a Bureau goal to provide technology capable of using low-grade domestic ores to meet emergency demands of the Nation for metals and minerals and in particular those minerals, such as chromite, which are considered critical. Two ores from California were ground and treated using gravity concentration and magnetic separation techniques. An are from Auburn in central California, assaying 2.5 pct Cr203, was treated by tabling and magnetic separation to yield a nonmagnetic product containing 44.7 pct Cr203 at a recovery of 36.4 pct. Core drilling samples from the Seiad Creek area of northern California, assaying about 6 pct Cr203, were upgraded by tabling to yield a concentrate containing nearly 50 pct Cr203 with a recovery of 50 pct. Both products are suitable for metallurgical and/or chemical use.

Jan 1, 1981

By J. A. Eisele, D. J. Bauer, D. E. Shanks

As part of its effort to produce cell - grade alumina from clay , the Bureau of Mines investigated the hydrogen chloride gas - sparging crystallization of aluminum chloride hexahydrate ( ACH ) from aluminum chloride liquor , to provide information for optimizing the crystallization operation . Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities , particularly phosphorus and magnesium , in ACH crystals are ( 1 ) aluminum chloride concentration in the feed solution to crystallization , ( 2 ) hydrogen chloride gas flow rate , ( 3 ) temperature , and ( 4 ) concentration of phosphorus and magnesium also in the feed solution . Parameters 1 , 2 , and 3 affect crystal formation . The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth . Aluminum chloride hexahydrate of cell -grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt - pct P205 and 0.010 wt - pct Mg0 . Crystallization temperatures less than 60° C decreased crystal purity .

Jan 1, 1965

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By D. E. Shanks

As part of its effort to produce cell-grade alumina from clay, the Bureau of Mines investigated the hydrogen chloride gas-sparging crystallization of aluminum chloride hexahydrate (ACH) from aluminum chloride liquor, to provide information for optimizing the crystallization operation. Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities, particularly phosphorus and magnesium, in ACH crystals are (1) aluminum chloride concentration in the feed solution to crystallization, (2) hydrogen chloride gas flow rate, (3) temperature, and (4) concentration of phosphorus and magnesium also in the feed solution. Parameters 1, 2, and 3 affect crystal formation. The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth. Aluminum chloride hexahydrate of cell-grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt-pct P205 and 0.010 wt-pct MgO. Crystallization temperatures less than 600 C decreased crystal purity.

Jan 1, 1981

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolanic-cement concrete to develop a low-strength backfill. Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan (fly ash) and lime. Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressive-strength curves that can be used to estimate the best backfill mix for any mine.

Jan 1, 1981

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By C. W. Smith

Research was conducted by the Bureau of Mines to determine the effectiveness of various types of crushers for use with the Bureau-developed pneumatic concentration technique for mica. Three types of crushers were investigated in this study, a roll crusher, a jaw crusher, and a hammer mill. All the mica concentrates produced contained over 82 percent mica, but recoveries varied considerably. The roll crusher gave the lowest recovery of 46 percent of the mica followed by the jaw crusher with a recovery of 50 percent of the mica. The hammer mill proved the most effective, producing four concentrates with recoveries of at least 70 percent.

Jan 1, 1981

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By Jon C. Volkwein

The canopy-air curtain was originally developed by the Bureau of Mines to surround the operator of a continuous mining machine with a zone of clean air. This report describes the application and testing of a canopy-air curtain on a gathering-arm loader, as well as some of the problems associated with providing a zone of clean air to a standing, semimobile operator. The area of air-curtain coverage and effects of air velocity are discussed. In its present form, the canopy-air curtain provides a 50 percent reduction in respirable dust to the operator.

Jan 1, 1981

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr&apos;s envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981