Search Documents

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

By Ann G. Kim, Thomas R. Justin, John F. Miller

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, PA. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic test and subsurface temperatures was not significant.

Jan 1, 1992

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By T. R. Taubert, D. H. Carlson, J. H. Johnson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO, NO, and NO, at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory- grade instruments. Concentrations of CO and CO, measured by the EMA were usually within + 14 pct of concentrations measured by laboratory-grade instruments for CO and 220 pct for CO,. EMA- measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO, differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1992

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By J. E. Chilton, C. R. Carpenter

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro- chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1- to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light- emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 1992

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By James J. Jessop, Richard E. Thill, Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 1992

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-g (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet, and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 1600 C for 1 h dissolved more than 95 pct of the PGM from virgin catalysts and more than 90 pct from used pellet catalysts. More than 85 pct of the PGM was dissolved from used monolith catalysts when a third autoclave step was added. Solid PGM concentrates containing more than 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 2500 C and used catalyst to 2750 C for 1 h. The solution after heating contained less than 0.2 ppm. total cyanide. The virgin residues passed the EPA Extraction Procedure Toxicity Test (EP Tox Test), the EPA Toxicity Characteristic Leaching Procedure (TCLP), and the California Waste Extraction Test (WET) for all elements except Ba. Adding sodium sulfate (Na2S04) to the virgin leach residues reduced the amount of Ba dissolved to an acceptable level. The used leach residues passed the EP Tox Test for all elements but failed the WET and TCLP for Pb.

Jan 1, 2010

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010

By James P. Ulery, Stephen J. Kravits, William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and Beth Energy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from overlying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the Iongwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 1992

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010