Search Documents

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

By Robert L. Rough

This report presents the results of an investigation by Federal Bureau of Mines engineers of water-injection projects in the northwestern Pennsylvania and southwestern New York area, where oil-producing wells have been converted from pumping to flowing. Data from 24 leases converted to flowing were collected and examined. Only 10 leases had information of significant scope for inclusion in the final analysis. The projects were classified in one of two categories. Group I consisted of leases operated to permit an evaluation of operational changes in terms of existing pressure differentials between injection and producing wells. Group II included remaining properties, for which enough information was available to justify an economic analysis but which did not have sufficient production data to support an engineering study because of radical changes in operational techniques. Variations in production and costs resulting from conversion to flowing were examined for production methods, well-spacing and completion techniques, and reservoir characteristics. Where water-injection rates were constant, oil production usually decreased rapidly at the time of conversion; production then increased slightly for 6 to 8 months before resuming a normal decline rate considerably below the estimated pumping rate. The abrupt decrease in production after conversion is indicative of lower pressure differentials between injection and producing wells, caused by the increased hydrostatic head in the producing wells.

Jan 1, 1960

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By H. S. Caldwell

This report describes work by the Bureau of Mines on the vacuum distilla¬tion of some of the more volatile metals such as cadmium, zinc, and magnesium from lead and tin. Evacuation within a distillation apparatus allows rapid diffusion of vapor away from the evaporation surface and prevents reaction of the vapor with residual gases. A reduction of pressure to several tenths of a millimeter makes possible practicable distillation rates, at temperatures for which the partial pressure of the metal vapor exceeds 10-3 atmosphere. The rate and selectivity of distillation depend primarily on the volatility and molal ratios of the alloy metals, and their chemical activity to each other. For very rapid evaporation or low concentration of the more volatile constituent, the rate is determined by the rate of diffusion of the evaporating metal, to the surface of the melt. Cadmium, zinc, magnesium, and tellurium were found to volatilize readily from both lead and tin. Tellurium appears to volatilize as an intermetallic compound rather than the pure metal. Antimony could not be removed from lead at 1,000° C.; the condensate was nearly all lead. Antimony, bismuth, and lead were removed from tin.

Jan 1, 1960

By Robert W. Smith

Computation of the thermodynamic properties of the reaction products in the deflagration of explosive gas mixtures has been a most valuable guide regarding the possible kinetic mechanisms of homogeneous combustion processes. Knowledge of the physically possible end states is indispensable for understanding observed deviations from equilibrium in heterogeneous combustion. However such information on dust flames is entirely lacking. To complement a Federal Bureau of Mines study of stationary graphite dust flames burning in pure oxygen,6/ this report gives examples, at atmospheric pressure and room temperature, of composition profiles in an idealized oxygen-dust flame, with both mass and enthalpy being preserved. Similar profiles can be obtained from the data of the paper for elevated temperature and pressure.

Jan 1, 1960

By G. L. Cook

The design of a dual-inlet system for a Consolidated model 21-103C mass spectrometer is described in detail. The system permits both high-mass and low-mass samples to be run by using a single instrument. The difficulties of using a single instrument for both purposes are given and a method of minimizing these difficulties through the use of the present design is discussed, After examining the experience of five years of use, the conclusions are that the bimodal operation is practical and the low-mass analyses had nearly the same precision as before the modifications to the instrument were made. In 1951, O'Neal and Wier.5/ published the first description of the modifications made to a mass spectrometer so that the spectra of hydrocarbons with molecular weights up to 600 could be obtained. Further discussion of the equipment of O'Neal appeared in 1953.6/ Also, Brown, Melpolder, and Young7/ described a parallel inlet system designed to reduce sorption effects at room temperature.

Jan 1, 1960

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall employment and injury experience for coal mines-bituminous, lignite, and anthracite; coke, petroleum and natural gas; and peat and slag plants; metal and nonmetal mines; sand and gravel operations; stone quarries; metallurgical plants, including metal mills and smelters; and nonmetal mills for 1959. Volume I of the yearbook contains injury experience and employment data in the metal, non-metal, sand and gravel, slag, and quarrying industries, and the milling operations and related plants. Volume II contains the injury experience and employment data in the fuel industries--coal, coke, petroleum and natural gas, and peat. Surveys conducted by the Bureau of Mines were the source of injury and employment data used to compile the tables and furnish information for the accompanying text. Response to the surveys was voluntary except that for coal mines. The Coal Mine Safety Act requires operators of coal mines to furnish the information requested.

Jan 1, 1960

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

A revolutionary development in blasting materials has occurred in the past 5 years. Ammonium nitrate, sensitized by the addition of a few percent of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2/ by a wide variety of mining and heavy construction operations. Moreover, ready availability of the component supplies throughout the Nation and ease of their formulation into effective blasting agents have made it possible for the blaster himself to pre-pare the mixes at the site of use. Although these field-mixed products have partly or wholly displaced explosives such as dynamites in some applications, there are other blasting operations where the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. Important safety characteristics are inherent in ammonium nitrate-based blasting agents prepared under competent factory control, or when field mixed under equivalent close control--as long as the hazards they present are clearly understood and respected. This publication attempts to summarize knowledge of those hazards and to incorporate practical ways to cope with them. A series of safety recommendations thus is presented. These recommendations cover the preparation, storage, transportation, and use of field-mixed ammonium nitrate blasting agents.

Jan 1, 1960

By Sidney Katell

Tonnage oxygen plants are or can be made available in sizes ranging from 150 to 1,000 tons per day. Capital requirements are estimated from $5,400 to $14,700 per daily ton, depending upon size of plant, cycle employed, and purity and discharge pressure of the product. Similarly, operating costs before return on investment will range from $4.80 to $10 per ton. INTRODUCTION Several processes4 5/ that can be used to convert coal to synthetic liquid fuels, synthetic pipeline gas, or hydrogen require high-purity oxygen as one of the basic raw materials. Depending on the and product and its specific use, the oxygen required will be of 95 or 99.5 percent purity. The quantity required, in turn, depends on the process for which the oxygen will be used and the size of the processing plant and will range from 150 to 4,000 tons per day.

Jan 1, 1960

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By John C. Machisak

THE INJURY data and experience at quarries and related plants of the United States are presented in this publication under the following general sections (A) General injury experience: Tables 1-3: Current data on number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 4-5: Current data on number of injuries, injury-frequency rates, location, accident agency, degree of injury, and related employment, data. (C) Injury experience by States: Tables 6-20: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 21-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and nondimension-stone quarries and at underground quarries. (E) Historical injury experience: Table 31: Injury and employment data on the quarrying industry for 1911 through 1957. Statistical data on injuries and related employment in the quarrying industries have been collected annually from the operating companies since 1911. Reporting to the Bureau of Mines is voluntary; there is no Federal law compelling operators of quarries and related plants to supply such data. Data presented herein may not be complete for the entire industry. They are however, believed to be representative of the hazards common to all quarry and related workers. Moreover, the figures are comparable as between States-a significant fact in view of the lack of uniformity among the States with regard to the classes of injuries covered by State reports and other factors that tend to make it impracticable or impossible when using State records to

Jan 1, 1960

By C. G. Kirkland

An apparatus for determining trace impurities in Grade-A helium by mass spectrometer methods was designed and built by the Federal Bureau of Mines. Grade-A is the designation for helium commercially produced by the Bureau. Its nominal purity is 99.995 percent. The device, following a suggestion by Deaton, concentrates the impurities in the helium by freezing them out in a coil-and-trap assembly cooled by liquid helium. A known volume of helium is passed through the trap, the concentration ratio determined, and samples of the concentrated impurities are analyzed by mass spectrometer methods. The apparatus has been in service for approximately 20 months and has satisfactorily met all requirements. Over 200 analyses were made of helium contained in conventional cylinders, obtained from the Amarillo, Exell, Otis, and Navajo Helium Plants, during the 6-month period ending March I, 1959. Total impurity concentrations, in parts per million, were as follows: Amarillo, 19.1; Exell, 17.1; Otis, 11.3; and Navajo, 6.6. Neon and nitrogen were the major impurities. Complete data are shown in table 4 in the body of this report.

Jan 1, 1960

By H. F. Weaver

The 18th National First-Aid and Mine Rescue Contest was held in the Memorial Auditorium, Buffalo, New Vork, October 5, 6, and 7, 1959. The meet was sponsored by the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with State mine inspection agencies, management and labor of the mineral extractive industries, and other safety minded groups. The Arrangements Committee, as authorized by the General Committee, made a11 the necessary arrangements for conducting the 1959 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1960

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

"M bed, Matanuska valley, Alaska, coal carbonizingproperties B 510M spectral lines, low-energy, study RI 5538Mab shaft, Leadvile district, Colo., investigation RI .1518Maberry process, for aluminum chloride TP 321"

Jan 1, 1960

By W. J. Wenger

THIRTY-FOUR analyses of crude oils from the fields of the Four Corners Area of Arizona, Colorado, New Mexico, and Utah are presented and compared. The samples, taken from formations in four geological time periods, have high gravity and low-sulfur, -nitrogen, and -asphalt content. Generally, the oils are paraffinic in the low-boiling fractions, with increasing naphthenicity in the higher-boiling fractions. Oils from Cretaceous formations resemble other Cretaceous oils in the Rocky Mountains, but oils from Permian and Pennsylvania formations are unlike other oils of these ages in the Rooky Mountains. The differences in the oils are minor and cannot be used to distinguish between fields or between producing formations. With minimum special processing, the oils should yield large amounts of good-quality motor fuels. INTRODUCTION The only place in the United States where four States have a common junction is known as the Four Corners Area. This area (fig. 1) includes the northeast corner of Arizona, the southwest corner of Colorado, the northwest corner of New Mexico, and the southeast corner of Utah. It includes three major geological basins: The Black Mesa, the San Juan, and the Paradox. Major oil developments have occurred in both the San Juan and Paradox basins, but no discovery of commercial importance has been made in the Black Mesa basin.

Jan 1, 1960

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960

By M. M. Wong

A brief investigation was made to determine the feasibility of electro-refining beryllium in a KCI-LiCI-BeC12 bath. Thin, platelike crystals of beryllium metal were produced by electrolyzing technical-grade beryllium metal beads (about 94-percent purity) as the soluble anode. Operating cell conditions were: Temperatures of 450° to 600° C.; an inert atmosphere; bath compositions of (1) 38.1 mol. percent KC1, 54.8 mol. percent LiCl, and 7.1 mol. percent BeC12 and (2) 36.7 mol. percent KC1, 52.7 mol. percent LiCl, and 10.6 mol. percent BeC12; cell voltages of 0.30 to 0.80; and initial cathode current densities of 50 to 435 a./sq, ft. Current efficiencies ranging from 87 to 96 percent were obtained. Qualitative spectrographic analyses of the metal products indicated that impurities were reduced. This technique offers the possibility of producing a grade of beryllium purer than that now generally available, which may have better mechanical properties.

Jan 1, 1960