Search Documents

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of nine manganese-ore samples in 1953-1954. Three samples were from Nevada and the other six from California. These samples represent marginal or low-grade ores from deposits that have been mined selectively in the past. The present interest lies chiefly in the possibilities of concentration of the remaining low-grade ores for economical exploitation. The treatment methods included gravity concentration and flotation in most cases. Results were sometimes unsatisfactory, particularly when the ore was too fine grained for liberation of the minerals within economical grinding range. The contaminating gangue minerals, such as quartz and iron oxides, were locked with the manganese to an extent that prevented separation of high-grade concentrates with satisfactory recovery. In cases where fairly good concentrates were made, it was at the expense of recovery, a condition typical of low-grade ores.

Jan 1, 1955

By J. D. Clendenin

Systematic practices for protecting crops from frost damage began in the United Metes more then 40 years ago when the Weather Bureau Fruit-Frost Warning Service was organized; however, various practices employed in frost protection are centuries old. Although there are areas where little doubt exists as to whether protection is needed, there are also circumstances where there is some doubt as to the need for frost protection. Many factors influence this, including not only critical temperatures but also the maturity dates of the crops relative to marketing. Critical temperatures for frost damage to trees, plants, blossoms, and fruits very with weather, plant variety and nutrition, and stage of growth. In the case of truck crops, a single night of protection from frost injury might yield big dividends with a variety of sweet corn or tomato that matures early while price is high yet be worth very little with a midseason or late-maturing variety. Consequently, it is the individual grower who must decide whether to use frost-protective measures on the basis of his returns, the quantity and quality of his crop, the marketing situation, the sensitivity of his crops to frost damage, and the frequency of damaging frost in his area.

Jan 1, 1955

By Irving Hartmann

Several recent ignitions of firedamp - a mixture of methane and air - in American coal mines have been attributed to frictional heating when hard rocks were struck while cutting and drilling coal seams. Although none of these ignitions caused severe explosions, they call attention to a problem that can become increasingly significant as mechanized mining is developed further. The power in and rapid release of energy from high-speed machinery has increased the rates of advance into virgin coal creating many problems. Unforeseen faults and hard mineral inclusions may be encountered; coal brought down in this way is finer in size; more gas is released from the seam; it is frequently more difficult to provide adequate ventilation at the' face; and new roof-support problems must be solved. In particular, continuous mining machines (also known as continuous miners) greatly increase the frequency of contact between cutter bits and minerals. In view of these conditions, it may be expected that more gas ignitions will occur as a result of frictional heating unless the situation is understood and remedial measures are introduced. The problem of frictional heating is not new in coal mining. In Europe, particularly in England, it has been a concern for more than a century. During the last 15 to 20 years frictional ignitions have been a major cuase of explosions in British mines. Explanations for the greater number of such ignitions in England may be the special character of the coal measure strata, the mining methods, the rate of gas emission and possibly its composition, and less effective ventilation near the face. To reduce the ignition hazard, considerable laboratory and field research has been conducted, particularly by the Safety in Mines Research Establishment, Ministry of Fuel and Power of Great Britain. Much of the information presented in this report has been drawn from these studies.

Jan 1, 1955

By E. R. Palowitch

Coal wasted with mine refuse represents losses in overall recovery of merchantable coal to the mine operator and a concomitant reduction in domestic reserves of available coal. Fraser, Kelley, and Graham3/ in studying the available coal in mine refuse in the Pittsburgh district of western Pennsylvania have estimated that at least 1 ton of mine refuse is produced for each 10 tons of merchantable coal and that 20 percent of this mine refuse might be recovered as salable coal by mechanical cleaning. SUMMARY This investigation dealt with the mechanical recovery of coal from wine refuse by a dense-medium washery employing pulverized mine rock as the dense medium and operating at a rate of 175 tons per hour. Two types of mint refuse were tested: Freshly mined and that .which had been mined 2 years before and piled on a waste dump.

Jan 1, 1955

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By Perry G. Cotter

As a portion of a general program for the synthesis of hard materials, a method was sought by which the hardness and density of tungsten carbide (WC)-cobalt compacts could be increased. It was demonstrated by Cotter that these improvements in quality could be made by employing an electric-resistance sintering process in which heat and pressure are applied simultaneously to presintered compacts composed of powdered tungsten carbide and cobalt. This conclusion was based on tests of material prepared by Cotter on welding equipment in use at the U. S. Naval Engineering Experiment Station, Annapolis, Md., and at Rensselaer Polytechnic Institute, Troy, N. Y. Rockwell-hardness tests made at Norris and core-drilling tests made at the Mount Weather Station of the Bureau of Mines indicated that, for some purposes, carbide material made by this process might be superior to the chemically analogous commercial products prepared by ordinary sintering methods. A program to develop optimum conditions for the electric-resistance sintering of tungsten carbide-cobalt compacts was initiated. The program was followed by a systematic evaluation of the hardness and density of compacts prepared by this method along with a series of carbide compacts furnished by various manufacturers. This paper presents a description of the electric-resistance sintering of tungsten carbide-cobalt compacts and the results of comparative physical tests.

Jan 1, 1955

By J. G. Kirby

The number of petroleum refineries in the United States continued to decline during 1954, and according to the Bureau of Mines annual survey there were 326 refineries with a total daily throughput capacity of 8,420,630 barrels, as of January 1, 1955. The increase in capacity for the year was 413,733 barrels daily, while the number of refineries declined 11. The capacity of the average refinery to process crude oil increased during 1954 from 23,759 barrels daily to 25,830. Breaking down the crude-oil capacity increase, by refining districts; 32 percent was installed at refin¬eries located in the Texas Gulf Coast district, 25 percent in the East Coast district, and 13 percent in both the Louisiana Gulf Coast and the California districts. The Appalachian No. 1, Texas Inland, and New Mexico refining districts reported declines in capacity during the year. Additional crude-oil capacity under construction, January 1, 1955, totaled 146,800 barrels daily. Included in this total are 4 new refineries, 1 each in California, Minnesota, New Mexico, and Washington. In addition to the' new facilities, equipment producing 1.49,550 barrels daily is being replaced.

Jan 1, 1955

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By M. R. Geer

Full-seam mining with continuous mining machines in dirty coal beds may increase loss of coal in the washery refuse. At one mine mentioned in this report the loss of salable coal was increased sixfold. Cleaning trials were made on three samples of jig refuse in a dense-medium pilot plant to demonstrate the application of this process to the recovery of coal from waste. These tests demonstrated that coal could be separated from impurity with the same degree of sharpness obtained in treating raw coal by dense medium. However, the recovery efficiency achieved in treating refuse averaged distinctly lower than that possible with raw coal because of the greater proportion of intermediate-density material in the feed and the lower yield of clean coal.

Jan 1, 1955

By R. C. Buehl

An experimental iron blast furnace of 3-foot-diameter hearth, producing about 12 tons of metal per day, was operated for 2 weeks with various proportions of anthracite replacing a corresponding amount of coke. The furnace operated well with anthracite in amounts up to 40 percent of the total fuel and produced metal of uniformly low sulfur and normal silicon contents. An increase to 50 percent anthracite during two attempts resulted in poor operation and the charge hung in the s haft of the furnace. INTRODUCTION Anthracite production in Pennsylvania decreased from 84,400,000 net tons in 1926 to 40,600,000 net tons in 1952, and there was a further decline in 1953 to 30,900,000 net tons. Employment in the anthracite industry dropped from 165,000 men working an average of 244 days per year in 1926 to 57,900 working an average of 163 days per year in 1953,3/ which has naturally resulted in considerable unemployment in the region. The industry is actively engaged in promoting new uses for anthracite to increase the demand and thus improve economic conditions in the region. One possibility is the use of anthracite to replace part of the coke for smelting iron ore in blast furnaces. The tests in this report were made to determine whether this use of anthracite would be feasible.

Jan 1, 1955

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Seth T. Reese

THE INJURY DATA and experience at coke ovens in the United States for 1952 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, frequency rates, and accident agencies involved in causing injuries. Data are given for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data in the coking industry covering 5- and 10-year periods on the number of injuries, accident agencies, and severity of injuries. (C) Historic injury experience: Tables 16 to 19: Contain data on the number of injuries, frequency rates, and employment at coke ovens from the earliest records through 1952, Operating statistics from 1929 through 1952 are given in table 19.

Jan 1, 1955

By M. J. Spendlove

A progress report is presented on a research program in which an attempt was made to develop a practical sulfide-volatilization process for recovering tin from low-grade Bolivian ores. Shaft-furnace designs and operating techniques were studied in a series of experiments in which the objective was to sulfidize cassiterite to stannous sulfide, remove the stannous sulfide by volatilization, reconvert the stannous sulfide to stannous oxide, and collect the resulting fume. A shaft furnace was developed and operated in a final test in which many of the previous difficulties were surmounted. Since the supporting funds were exhausted at this point, the project was discontinued; recommendations for further improvements in furnace design and operation were made on the basis of interpretation of experimental results obtained in shaft-furnace experiments and other related studies.

Jan 1, 1955

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By Lloyd Williams

1. The investigation shows that the Pewee, Big Mary, and Windrock are the most important beds in Anderson County. About 73 percent of the known recoverable reserves of coal in the county are in these beds, and from them comes 94 percent of the production. The remaining reserves tabulated in this report are in the Joyner, Jellico, Coal Creek, and Poplar Creek beds, and 6 percent of the county production comes from these beds. No production is being reported at present from the Jellico bed, although it was mined years ago. 2. Known measured and indicated reserves in all beds, bared on a minimum thickness of 1/4 inches and on 1,800 short tons put acre-foot of coal in place, are estimated to be 170 million torts as of January 1, 1953 Of this total, 155 million tons is in beds 2S inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to they total estimated reserves.

Jan 1, 1955

By William J. Campbell

The columbite-tantalite mineral series was studied by various instrumental techniques to establish the relationship of density to composition. The samples used were carefully selected to obtain a mineralogical purity of at least 98 percent. Impurities were determined by optical microscopy, X-ray diffraction, and optical and X-ray spectroscopy. Each sample was analyzed by fluorescent X-ray spectroscopy for iron, manganese, columbium (niobium), and tantalum. The existence of a unique relationship in this isomorphous series permits a simple correlation of the intensity of a spectral line with the concentration of the analytical element.

Jan 1, 1955

By J. E. Shelton

This presentation covers the results of laboratory studies conducted by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg., on alluvial sands from Dismal Swamp, Bear Valley, and Cascade, Idaho. The search for radioactive minerals has led to the reexamination of alluvial deposits; in the process of this reappraisal the frequent presence of minerals bearing columbium and/or tantalum was toted. Because of increased demand for these metals by the defense industries and because these industries depend upon foreign sources for their supply the domestic alluvial black sands are being considered, as a possible domestic source. However, utilization of these alluvial deposits depends upon development of methods of concentrating these valuable minerals. The primary objective of the test work was the study of the effect of attrition scrubbing, sizing, magnetic, electrostatic, and gravity separa¬tion as methods for concentrating and recovering the columbium and tantalum-bearing minerals, samarskite, euxenite, ilmenorutile, and columbite.

Jan 1, 1955