Search Documents

By T. M. Garland

This report presents a Bureau of Mines assessment of crude oil and associated gas production and reserves that would result from different drilling efforts in the lower or contiguous 48 States during the 1972-85 period. The drilling effort was based upon five growth rate assumptions from the 1971 level. Additions to crude oil reserves were computed for nine cases resulting from the use of three equations for findings per foot drilled and three constant revision factors. The results indicate that the United States will not become self-sufficient in crude oil production by 1985 and also illustrate the lead time required to reverse the decline in oil production. Discussion is limited to three of the nine cases to provide high, intermediate, and low results. More emphasis is on the intermediate case because it is indicative of the most probable trends. The methodology and statistical data are included in the appendices.

Jan 1, 1974

By K. J. Miller

Electrophoretic mobility measurements of coal and pyrite particles in distilled water revealed a difference between the migration speeds of the two materials toward the anode in a dc electric field. This information led to the development of a laboratory electrophoresis column for separating fine pyrite from coal by utilizing the electrokinetic and the specific gravity differences between coal and pyrite. The study demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis using a stage separation technique. In a cost analysis, electrical power for electrophoresis was extrapolated to about $1 per ton of clean coal product. But, since the only successful tests ever made were in the laboratory with prewashed samples of minus 100-plus 325-mesh coal in distilled water, the cost figure derived is not representative of conditions prevalent in commercial coal cleaning operations. True conditions would reflect costs many times as great. In the course of the work, several scale-up techniques were considered but their feasibility became academic in view of the physical and economic problems associated with electrophoretic separation of pyrite from coal. Although the process and apparatus were finally deemed impractical for commercial coal preparation, the electrophoresis column may have some application as a laboratory device.

Jan 1, 1974

By R. V. Ramani, P. M. T. White, D. Sutton

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. The project personnel express their thanks to Dr. Jay Politzer, The Pennsylvania State University Computer Center for providing the subroutine POLITZ and function IFIND, to Dr. Ray Masters, Department of Architectural Engineering, for permission for the use of the GRID program and to Dr. Lother Weyher of Bethlehem Steel Corporation for providing coal data.

Jan 1, 1974

To improve the efficiency and speed of under-ground post-disaster rescue operations. The Approach: Develop a battery-powered mine-rescue vehicle designed to carry rescue crews, rescued miners, and their support equipment. How It Works: The experimental vehicle, shown below, was designed and constructed by the Mine Safety Appliances Company under contract to the Bureau of Mines. ATV Manufacturing Company and Delco Electronics were subcontractors. A rechargeable, silver-zinc battery provides power to a 3-horsepower permissible motor, the speed of which is regulated by a solid-state controller. Three wheels on each side are independently driven by a chain and mechanical trans-mission.

Jan 1, 1974

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By Arnold F. Stalder

The measurement of various gas concentrations in the atmosphere at a particular location has become a problem of considerable importance. Levels that need to be monitored vary from the range of percent for constituents such as oxygen to parts per million levels for gases like nitrogen dioxide. In particular, mine air can become contaminated with noxious or toxic gases from several sources: fires within the mine, diesel-powered equipment, and explosive sources. The contaminants that result are carbon monoxide (CO), carbon dioxide (CO2), and oxides of nitrogen (NO and NO2). Additionally, oxygen (O2) may be depleted. Thus, the workman can be exposed to potentially toxic or asphyxiating atmospheres. A device was needed that will continuously monitor the mine air in working areas and provide warning of hazardous atmospheres. The Mine Air Monitor was conceived as being a portable, rugged instrument capable of measuring the concentration of the various atmospheric constituents in the mine environment. The unit was to provide both warning signals and quantitative measurements when hazardous contaminants existed at too high a level, or when the oxygen was being depleted. The initial concept involved optical sensors for all of the contaminating gases to be measured, namely CO, CO2, CH4, and NO2, and an electrochemical cell to monitor O2. When the explosion proof requirements of Schedule 2-G made the concept appear to be unfeasible from the standpoint of weight and portability, the program was redirected and a three channel monitor employing electrochemical sensors was adopted. In this case the gases to be monitored were O2, CO and NO2. The remainder of the program was oriented towards obtaining good, commercially available lectrochemical sensors for the above gases, testing them, reducing deficiencies noted during these tests, and making the necessary modifications to integrate the three sensors into a Mine Air Monitor suitable for the mine environment.

Jan 1, 1974

Over and above the technical support arid consulting work described in the preceding Parts of this Volume, ADL staff also provided a wide range of additional technical assistance to the Bureau on an ad hoc basis over the course of the contract, and particularly in 1973. Some of these assignments were on tasks that temporarily assumed a high priority at PMSRC, requiring a fast response, while others were more suited to conventional schedules but on communication and location topics less directly related to those in the preceding Parts. Chapter I briefly describes some of the diverse short-term assignments while Chapters I1through V treat assignments on the other topics. I SHORT-TEXM ASSIGNMENTS A sampling of short-term, fast-response assignments undertaken on mine communications and miner location for PMSRC during 1973 are given below. These assignments included technical reviews, discussions and recommendations related to the theory, experimental data, designs, and hardware implementation of experimental CW and pulse miner location EM transmitters; preparation of technical performance specifications for a miniaturized preproduction prototype CW electromagnetic location transmitter; review of specifications for a seismic signal detection experimental study; participation in technical discussions and experiments with PMSRC and equipment suppliers regarding the UHF radio/radiax-cable communications installation in the Bruceton mine; participation in an informal conference to discuss mine communication and monitoring needs and preferences with representatives of the Bureau, mine operators, and equipment manufacturers; participation in technical discussions with representatives of a U.S. mine operator and CERCHAR* concerning the characterization of faults on trolley lines and means of improving their rapid detection;** recommendation of simple signal, noise, and ground fault measurements on mine phone lines; review of an inexpensive automatic telephone dialer; preliminary discussions regarding the feasibility of adapting and assembling a collection of available telephone industry carrier equipment for installation and test in an operating coal mine; evaluation of a proposed call alert mine paging system; review of hardware designs and future experiments for a mine communication sled; design critique of a proposed six-channel narrow-band FM voice modem for carrier communication on the mine phone line; preparation of technical performance

Jan 1, 1974

By I. A. Jacobson

In a closely controlled laboratory retorting system for oil shale, a relationship was developed by the Bureau of Mines between the temperature in the retort and the weight ratio of ethylene to ethane in the gases produced. Reciprocal temperature was shown to be directly proportional to the log ([ethylene]/[ethane]). From this relationship a number, called retorting index, was developed. The retorting index has the dimension of temperature, but its magnitude depends on both temperature and residence time for the reactants in the heated zone in the oil-shale retort. The slopes of the lines relating reciprocal temperature and the logarithm of the ethylene-ethane ratios are nearly constant for each of the retorting processes for which data have been presented. The retorting index should be a valuable tool to control the operation of oil-shale retorts, either aboveground or in situ. If an optimum operating condition can be established, the maintenance of the optimum or the departure from it should be easily monitored by use of the index.

Jan 1, 1974

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By W. K. Kleysteuber

This report covers the design and testing of a novel bulk materials conveying device by the Bureau of Mines. The transport concept of the device is to create a traveling wave with a steep front so that the bulk material slides and cascades down the front of the wave with some horizontal motion. Ideally, the front should act like a continuous chute. The concept of moving bulk materials along a belt without any forward movement of the belt itself was demonstrated. The conclusions reached were that the mechanism as designed could not overcome the inherent major disadvantages that would make the undulatory conveyor suitable for practical applications.

Jan 1, 1974

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By R. V. Ramani, P. M. T. White, D. Sutton

4.1 Introduction Using methods outlined in previous sections of this report, programs were written and/or obtained to: i) select best combinations of "a" and "k" for up to 8 different value parameters, ii) calculate available and unavailable ore tonnages and other statistics, and iii) produce contour maps of various parameter characteristics and available tonnages on a line printer. All the above programs are written in Fortran IV for execu¬tion on IBM 360/370 computers. 4.2 Calculation of Coal Reserves The Ore Reserve program suite consists of the following sections: (a) UNIT 1: This unit is a subroutine called by Unit 2 to determine values for "a" and "k" from the given data. (b) UNIT 2: These programs calculate ore reserves and are composed of a main program and several sub¬routines. In the following, their functions are abbreviated: i) MAIN - calls subroutines, reads run parameter variables, reads borehole data and interpolates grid node values for the area of investigation

Jan 1, 1974

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 20 or 30 ampere leak, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1974

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,540,700 for the 1.06-million-ton-per-year (MM tpy) mine to $44,720,500 for the 4.99 MM tpy mine. Total capital investment ranges from $21,850,700 to $75,693,500 for the same mines. Corresponding selling prices for the coal range from $8.76 to $7.53 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By M. L. Whisman

Three samples of waste lubricating oil were re-refined by processes developed by the Bureau of Mines and reformulated with additives to meet designated requirements for viscosity and service. Quality-defining bench-scale tests were used to compare and evaluate the quality of these three motor oils, eight commercially re-refined lubricating oils, and three new lubricating oils. Most of the re-refined oils studied could not be distinguished from new oils by the bench tests used to define quality. There was some evidence, however, that one and perhaps more of the re-refined products investigated might not meet all of the quality standards of new lubricating oil, suggesting the need for better quality controls by re-refiners.

Jan 1, 1974

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By E. C. Foster

The project objective of this contract is to design, develop, and demonstrate a dust collecting system for auger head miners, used in coal seams 40 inches or less in height, which will reduce respirable dust below the limits established by the Federal Coal Mine Health and Safety Act of 1969. This system was to be incorporated into 3 Wilcox Mark 20 continuous miner. In order to accomplish this, the objective was divided in three main areas. First: To develop a dust control system which would remove by isolation, respirable dust from the face area and areas where miners work. Second: To develop a dust scrubbing system to remove and collect float dust before the air reaches the return airway. Third: To reduce the overall noise levels to which the miners are exposed.

Jan 1, 1974

By Fun-Den Wang

Finite-element structural analyses were performed to determine the stress distribution and displacements around a single rectangular coal mine opening in a multilayered rock system. The effects of changes in mechanical properties of roof and coal layers, roof layer and mine opening geometry, horizontal-to-vertical load ratio, and structural geologic features on the stress distribution about the opening were studied. Variability in the stiffness and relative thickness of the immediate roof layers can produce a considerable difference in the stress distribution about the opening as compared with that of a homogeneous material. Changes in opening width and horizontal-to-vertical load ratio have different effects on the stress distribution about the opening depending on the composition of the roof layers. In general, where a stiff layer exists in the roof at the surface of the opening, the stresses are higher in the roof and ribs around the opening. Horizontal changes in facies in the roof layers produced by structural geologic features can also greatly alter the stress distribution about the opening compared with the simple layered cases.

Jan 1, 1974