Search Documents

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By Sidney Katell

The present report, a continuation of the series of Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, is concerned with articles published from January 1958 through December 1958. The periods covered in previous reports are as follows: January 1930 - August 1948 I. C. 7516 September 1948 - June 1952 I. C. 7705 July 1952 - June 1954 1. C. 7751 July 1954 - December 1956 I. C. 7847 January 1957 - December 1957 I. C. The following sources were used to obtain the references to and the abstracts of the published articles included in this report: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Coal Age. 6. Coal Utilization. 7. Cost Engineering. 8. Industrial and Engineering Chemistry. 9. Nucleonics. 10. Oil and Gas Journal. 11. Petroleum Engineering. 12. Petroleum Refiner. 13. World Oil.

Jan 1, 1959

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By Quintin A. Aune

This report presents the results of a field and laboratory study by the Federal Bureau of Mines, in cooperation with the California Division of Mines, of the swelling-type bentonite deposits in the Vallecitos area in San Benito County, Calif. The purpose of the study was to learn if these large deposits contain bentonite of sufficient quality and quantity to be of economic value as an oil-well drilling mud additive. Large amounts of bentonitic clays are used by the petroleum industry as well as the steel industry in California. Additional amounts may be required in the near future as a concrete or earth-fill admixture in constructing dams and canals in the California Central Valley. Depletion of some local clay deposits and loss of others to military installation areas have given new emphasis to the need for developing new bentonite deposits in California.

Jan 1, 1959

By W. L. Dare

This information circular is one of a series, published by the Federal Bureau of Mines, on methods and costs of mining uranium ore on the Colorado Plateau. This report describes the relatively small-scale operations of the Salt Wash miner: The mining method followed, the equipment used, and the production costs. It describes 10 lease-operated mines of Union Carbide: Nuclear Co. that are typical of Salt Wash operations on the plateau. These mines lie within the Uravan mineral belt3/ and arc in the Gateway, Bull Canyon, and Uravan mining districts. (See fig. 1.) Generally the ore bodies occur as irregular, discontinuous layers of ore minerals within sandstone beds in the Salt Wash member of the Jurassic Morrison formation. The ore bodies sometimes occur as rolls, pod associat with carbonaceous trash, or tabular masses. Their size and erratic distribution preclude the use of a prearranged and uniform stoping system. The mining method is simply to follow the ore and leave open scopes behind.

Jan 1, 1959

By Earl R. Maize

Epoxy and polyester-type resins were injected into coal-mine roof strata of the thick Freeport coal seam in Allegheny County, Pa., at test sites in roof that had been exposed several weeks, in newly exposed roof, and in strata over solid coal. Test results indicate that the method of strengthening bituminous-coal-mine roof by injecting a bonding material into the roof strata can be developed into a safe, efficient support system. If roof bonding will become a standardized method of roof support and reinforcement or if it can be effective when used with other types of roof support can be determined only by extensive experimentation in various coal beds. Observations and conclusions are shown at the end of this report.

Jan 1, 1959

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

By T. R. Jolley

This publication describes the control of fires in inactive coal deposits in the Western United States, including Alaska by the Bureau of Mines. Material presented should contribute to a better understanding of the purpose, process, and benefits of the program. Forty fires were extinguished or controlled in the Western United States and Alaska from 1948 to 1958 under a national program directed by the Bureau's Health and Safety activity. Thirty-five fires were controlled by smothering; three were controlled by the isolation method; and two were extinguished by removing the burning coal, smothering it with incombustible material, and backfilling the fire zone. The fire-control projects were distributed as follows: Alaska 2, Arizona 1, Colorado 9, Montana 9, New Mexico 4, Utah 2, and Wyoming 13. The total cost of the 40 fires extinguished or controlled was $1,203,957. Of this cost, 12.8 percent was engineering and administrative and 87.2 percent was contractual services.

Jan 1, 1959

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By Kenneth M. Earl

The purpose of this investigation was to obtain subsurface information on the John Burdette barite-fluorite deposit, Garrard County, Ky. The deposit was intersected in each of five inclined diamond-drill hales aggregating 1,163 feet. All holes were drilled from the hanging wall of the deposit; the inclinations varied from minus 41° to minus 75°. Disseminated metallic sulfides were noted in the drill cores from holes 1, 2, 4, and 5. The deepest drilling was hole 5, which intersected the deposit at approximately 490 feet down dip. Visual inspection of the cores did not indicate mineralization of economic importance; therefore, no chemical analyses were conducted. Condensed logs of diamond-drill cores are included in this report. All drill cores were shipped to the Bureau of Mines core library in Minneapolis, Minn., for future reference,

Jan 1, 1959

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959

By J. G. Walters

In a survey of the coking properties of United States coals, the Bureau of Mines has accumulated data on more than 500 coals and blends tested by the Bureau of Mines-American Gas Association (BM-AGA) method.4/ The importance of these tests depends upon the fact that a greater number of different coals has been tested in this apparatus than in any other of similar scale, thus permitting comparison of the carbonizing properties of many coals. Evaluation of BM-AGA results with respect to industrial data supplied by member firms of the American Gas Association was one of the first objectives in developing this test apparatus and procedure. Early data showed that, de-pendent upon BM-AGA carbonizing temperature, BM-AGA and commercial results agree closely.5/ Because of limited data, statistical relationships were not established at that time.

Jan 1, 1959

By Joseph A. DeCarlo

This publication presents statistical data on oven-and beehive-coke plants in the United States. Information on the carbonizing capacity of the coke industry is important because of the close relationship between the coke industry and most of the other basic industries of our country. Coke is an essential-raw material in pig-iron production; also, coal-chemical materials are used to make fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals, dyes, and many other useful products necessary to sustain and improve the high standards of living in our country. Oven-coke plants in the United States on December 31, 1958, are tabulated in table 1. This tabular presentation shows the location, classification, number and type of ovens, annual coke capacity, coal chemicals produced, and name and address of parent company for each individual coke plant. About 86 percent of the capacity of slot-type coke ovens in the United States is owned by iron and steel companies. In most of these plants the coke ovens are integrated with the blast furnaces to facilitate transportation of raw materials for steel making. This has resulted in large coke plants, and the average annual coke capacity of "furnace" plants in 1958 was 1.3 million tons. Nonfurnace or "merchant" plants include coke plants associated with chemical operations, gas utilities, as well as coke plants that produce metallurgical, industrial) and residential-heating grades of coke and coal-chemical materials for sale on the open market. These plants ordinarily are not as large as furnace plant~ and annual coke capacity of merchant plants in 1958 averaged only 500 thousand tons. At the end of 1958 there were 55 furnace plants and 22 merchant plants.

Jan 1, 1959

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By George C. Branner

This study was planned to present salient facts of the California and Nevada sulfur industries and to indicate existing opportunities for increased economic utilization of California and Nevada sulfur resources. Numerous publications on sulfur have been issued by the Federal Bureau of Mines, including Information Circular 6329, Sulfur, by Robert H. Ridgway (1930); annual Minerals Yearbook chapters on Sulfur and Pyrites, by various authors; and a chapter on Sulfur by G. W. Josephson in Bureau of Mines Bulletin 556, Mineral Pacts and Problems (1956). This literature, however, deals primarily with the national and international sulfur situation and does not attempt to analyze the possibilities for increased economic development of sulfur resources by individual States. The present study attempts to analyze these possibilities in California and Nevada and to (1) evaluate factors that have influenced production and consumption in California and Nevada and (2) indicate apparent trends in production, consumption, and prices in these States.

Jan 1, 1959

By D. E. Wolfson

This report describes the carbonizing properties of the principal coal beds of Allegheny County, Pa., which rank low in the high-volatile A bituminous classification. Seven coal samples from 3 coal beds were selected for study, as follows: 2 each from the Redstone and Pittsburgh beds and 3 from the Upper Freeport bed. Selection was based on estimated reserves. The samples of Upper Freeport and Pittsburgh coals were satisfactory chemically for producing metallurgical coke. The ash contents of the samples of Redstone coal were moderately high. One of the samples of Redstone coal was high in sulfur content, and it would be difficult to upgrade to meet present metallurgical standards.

Jan 1, 1959

By J. H. Field

Capital and operating costs have been estimated for removing sulfur dioxide from flue gases of a powerplant of 12,000-kw. capacity by liquid-purification processes, using limestone, ammonia, or sodium sulfite as the reactant. The annnonia and sodium sulfite processes yield end products that may be marketable. Coals containing about 1.5 and 5.0 percent sulfure have been considered. The sulfur dioxide content of the gases to be treated is 0.083 and 0.30 percent, respectively. Estimates have been made for 90-percent removal of the sulfur dioxide from both gases. A third instance has been considered in which 70 percent of the sulfur dioxide is removed from the flue gas of 0.30-percent concentration. The scrubbed gas would contain 0.09 percent sulfur dioxide, which might be within the permissible limit for discharge to the atmosphere in most areas. Although it is unlikely that flue gases with sulfur dioxide concentrations of less than 0.10 percent would require purification, a cost estimate for such a gas is included because an estimate is available for a British plant employing the limestone process at these conditions. Capital investment and operating costs, with no credit for products, are lowest for the limestone process for gases of both concentrations. Crediting the ammonium sulfate and sulfur produced in the ammonia process at their market prices at the end of 1956 of $32 and $28 per ton, respectively, the operating costs of the ammonia process become the lowest for purification of the gas containing 0.30 percent sulfur dioxide. The operating costs of the sodium sulfite process for purifying gas of high sulfur dioxide content approach those of the limestone process when the byproduct sulfur dioxide is credited at $14 per ton. Even if credit for products is allowed for the ammonia and sodium sulfite processes, the operating costs are higher than those of the limestone process for the gas of low sulfur dioxide content. Because of the large quantity of materials that would be produced by removing sulfur dioxide from a relatively small number of plants, credit for products should be allowed with extreme caution.

Jan 1, 1959

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959