Search Documents

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increased usage for acid mine drainage mitigation and abatement as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulphurization byproducts from Virginia Electric?s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1999

Despite the media's use of the mining industry as a whipping boy over its perceived attitude towards the environment, the facts remain that the only legislated requirement in the SA Statute Books for any form of environmental impact-assessment prior to development is to be found in the Minerals Act in the form of an EMPR. Not only is our industry complying with this requirement, but moves are afoot to set up environmental management systems for existing operations in preparation for seeking accreditation under ISO 14001 when published towards the end of this year. On how broad a front are we advancing? ? Is the industry equipped to handle these challenges? ? Does it have the determination to overcome its problems? ? Do we realise that failure may mean the loss of markets overseas to competitors who can meet the international standards? ? Where are the shortcomings and when must our efforts be focussed?

Jan 1, 1996

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

The current global economic climate has adversely affected the resources industry in general. For the gold mining industry, even though the gold price has been stable as compared to other resources, there is still a need to cut costs even further in order to be profitable and sustainable. Of all the costs that are associated with mining, comminution of ore accounts for the majority. Comminution costs constitute mainly electricity, grinding balls and liners. Of these three components, grinding balls form the major portion of the consumable costs, and can be as high as 40%?45% of the total. As a result, proper grinding ball selection is a key consideration towards reducing mining costs. This paper discusses quality control procedures that can be conducted in order to select the best grinding balls for a particular application. Keywords: grinding balls, forged, semi steel, hardness, chemical, metallography, wear testing, impact test

Jan 1, 2009

By T. H. Yang, Q. K. Wang, T. Song, J. W. Zhou

The grinding circuit can be one of the most important mineral processing circuits in plants. Along with the application of large-scale milling machines, the design and optimisation of the operation strategy for grinding circuits is more complicated. An in-house grinding process simulation tool was developed to mass balance, model fit and simulate crushing, grinding and classification circuits. An industrial grinding and classification circuit in a copper mine was modelled, and the modelling parameters were verified by a particular group of plant survey data. To justify the prediction ability of the fitted models, the model predictions under different operation conditions were compared with another group of plant survey data. Then the model predicted the effects on the circuit of changing operating conditions. Circuit analysis of the comminution process for water feed to a SAG mill, water feed to sump, the rolling speed of a SAG mill and the percentage of ball filling in a SAG mill was put into practise, based on the simulation results. The simulation results can be used to help plant operators understand the features of the comminution process and may help to build a knowledge library for process control. Keywords: Process modelling, grinding, comminution, circuit analysis

Jan 1, 2020

By V. V. Nazimko, A. I. Hohotva, S. N. Alexandrov, V. P. Sazhnev, V. S. Zaharov

Ground behaviour in the vicinity of a roadway has been investigated using a physical model and in situ tests during a roof fall. It was discovered that behaviour of the ground is governed by irreversible displacements of adjacent rock clusters. The cluster is a short-living sector of a rock mass that moves as a solid body. For the lack of degree of freedom, the rock mass must be divided into clusters that are forced to move one after another in space and in time. These clusters permanently rearrange and reform during irreversible (inelastic) ground deformation. The crowded clusters have to yield to each other and alter their velocity and direction of movement to accommodate their motion into the excavation. Such behaviour involves uneven and irregular vertical deflection and the movement of adjacent rock blocks in the roof, sides and floor of an opening. Such movement destroys the symmetry of horizontal displacements with respect to the centre line of the opening. A set of indicators that a roof fall is imminent has been identified. Horizontal displacements and dilation must be controlled in order to maintain the stability of an underground opening. Such a state retains the self-supporting effect of the roof and contributes to rock bolts bearing capacity.

Jan 1, 2003

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By J Cahill, M Lee

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Groundprobe?s Slope Stability Radar has enabled the Harmony Open Pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Ground probe?s slope stability radar has enabled the Harmony open pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By N. K. Singh

The calculation of resource volumes for large mineral sands deposits is the process of systematically compiling all known data in order to define the volume of ore contained and its intrinsic economic value. Traditionally, this process has been highly speculative in nature, as the variability of the layer thickness, even between closely spaced, boreholes can be highly variable. The issue of horizon continuity is of critical importance in mine modelling and resource definition. Accurate volume estimates are difficult to derive from drilling data alone, as the borehole spacing of an economically viable drilling programme is often greater than the spatial frequency of the variations in profile thickness. The limitations associated with this inferential approach to resource estimation can be mitigated through the use of newly developed ground penetrating radar (GPR) methods, thereby maximizing orebody optimization by reducing contamination and orebody loss. The use of GPR in the mining industry has historically been limited to shallow, high-resolution applications, such as the location of voids in limestone or the mapping of paleo channels for alluvial gold and diamonds (Francke and Yelf, 2003). These limitations have not been technology based, but rather market based, as the vast majority of GPR systems were originally designed for civil engineering applications. A new generation of GPR technology, designed specifically for maximum penetration in sand environments, is now being developed. This technology has been trialled extensively at the Richards Bay Minerals heavy mineral sand deposit in South Africa with optimistic results. The clay base of the mineral sands has been imaged to some 120 metres. Further equipment refinements are expected to yield even deeper profiling and higher resolution. The resolution offered by this technology is unique, allowing individual depositional sequences to be imaged and modelled in three dimensions. This paper will discuss the advances in GPR technology relevant to the mineral sands industry, as well as methods to optimize and integrate GPR data into existing mine models. Also addressed will be approaches to three-dimensional modelling of high-resolution GPR data and subsequent volume estimations.

Jan 1, 2007

By J. Hadjigeorgiou, Y. Potvin

In a benchmarking paper published in the SAIMM Journal, Potvin and Hadjigeorgiou (2008) reviewed ground control strategies to manage large deformations in underground hard rock mines. Significant differences were identified in the design and acceptable tolerance between civil and mining engineering practice for squeezing ground conditions. Variations were also noted in ground support strategies between Australian and Canadian mines. In this paper we review progress in design methodology and ground support practice since 2008, including the availability of more effective deformation monitoring, new design tools, greater access to yielding ground support elements, and better installation practices. An improved understanding of technical and practical issues associated with squeezing conditions has led to the development of ground support guidelines for a range of squeezing ground conditions in hard rock mines.

Jul 5, 2023

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008

By J. C. van Dyk, F. B. Waanders, J. Brand, C. A. Strydom

"Underground coal gasification (UCG) is a fast-emerging, in situ mining technology that provides access to low-cost energy through the utilization of coal reserves that are currently not technically or economically exploitable by conventional mining methods.Groundwater monitoring for conventional coal mining in South Africa is well established, with SANS, ASTM, and ISO standards for the specific environment, location, and purposes. South Africa’s groundwater is a critical resource that provides environmental benefits and contributes to the well-being of the citizens and economic growth. Groundwater supplies the drinking water needs of large portions of the population, and in some rural areas it represents the only source of water for domestic use. Implementation of, and adherence to, groundwater monitoring standards are thus non-negotiable.The groundwater quality management mission, according to the Department of Water and Sanitation in South Africa, is set in the context of the water resources mission and reads as follows:‘To manage groundwater quality in an integrated and sustainable manner within the context of the NationalWater Resource Strategy and thereby to provide anadequate level of protection to groundwater resources and secure the supply of water of acceptable quality.’ (SABS, 2016).In this paper we propose fit-for-purpose groundwater monitoring standards for a commercial UCG operation. It is important to proactively prevent or minimize potential impacts on groundwater through long-term protection and monitoring plans. Scope of study / standard proposal The purpose of this paper is to set out a National Standard Proposal to emphasize groundwater monitoring as one of the five strategies of the ‘Policy and Strategy for Groundwater Quality Management in South Africa’ (Department of Water Affairs and Forestry, 2000) and to align it with the National Water Act, Act no. 36 of 1998 (Republic of South Africa, 1998).The focus of this standard is directed solely towards groundwater monitoring during underground coal gasification (UCG). Groundwater in this context refers to water as sampled from dedicated monitoring wells around the targeted site, which will include the shallow aquifer referred to as groundwater, and water flow at the level of the underground gasifier, referred to as ‘coal water’."

Oct 1, 2018

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By W. F. Lorch

Growing use of deionised water in surface coating techniques by w. F. LORCH Production engineers in the metal plating, paint, plastics-coating and printed circuit industries are increasingly aware of the cost of sub-standard or blemished items which have been poorly processed. An area where quality control can quickly produce higher efficiencies is in the choice of suitably purified water for making up solutions, for rinse baths and 'drag-out' baths, for cleansing lines and electrophoresis tasks, for maintaining electrolyte density and hence consistency, and for facilitating the recovery of valuable minerals. The author of this article examines the general problems of using nonpurified water, and shows how purified water has become accepted by the principal surface coating industries to improve processes and effect economies.

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By Bjørn Nilsen, Werner Stefanussen

The construction of the Guaigui Multipurpose Project includes a 74 metre high concrete face rock fill dam, a 350 metre long diversion tunnel and a 350 metre long spillway tunnel. The topography in the project area is very steep, and the rock masses are characterized as soft rocks. The stability of the 80 to 100 metre high dam abutments and the excavation of the tunnels in soft rock conditions have caused various challenges and problems to be solved. Limited pre-investigations have called to a great extent for estimation of parameters for the stability calculations based on experience. The preliminary calculation of the stability of the planned rock slope above the spillway intake platform has been carried out by conventional partial factor methods and by use of a computed based Slide Program. The two methods of calculation give different results , and that rock support is necessary to obtain an acceptable factor of safety for a slope inclination of 52o. The input parameters for the rock mass characteristics need to be verified for the permanent calculations.

Jan 1, 2006

By T. Mapeta, S. M. Rupprecht

Discussions on reasonable prospects for eventual economic extraction (RPEEE) include the CRIRSCO 2019 reporting template, JORC 2012, SAMREC 2016, CIM 2019 Guideline, and Regulation SK-1300. These reporting codes all conform to the principles of reasonable prospects for eventual economic extraction. To demonstrate that all mineral resources align with the RPEEE principles, the Competent Person is responsible for endorsing the mineral resource estimate. Moreover, establishing mineral resources and RPEEE requires technical input from numerous technical specialists, such as mining and geotechnical engineers, metallurgical engineers, social and environmental specialists, financial and governmental practitioners, and more. The aim is to improve the transparency of the disclosure of mineral resources and guarantee the investor or potential investor that the reporting of mineral resources is based on reliable technical, economic, environmental, social, and other relevant factors. This paper discusses the important protocols and definitions in some international reporting codes for the purposes of developing a guide memoire that will assist the Competent Person to interpret, establish and apply RPEEE appropriately and easily.

Jun 27, 2025