Search Documents

By More-O&apos, R. C. Ferrall, J. W. Wilson

SYNOPSIS The theory of elasticity has been shown to provide a means of determining the stresses and displacements induced by mining in deep level hard rock mines. This theory has been incorporated into an electrical resistance analogue on which the plane of a reef or ore-body can be modelled to enable the rapid determination of stresses and displacements at points in the plane of the reef. This electrical analogue has been used to determine energy release rates caused by scattered mining, which, to some extent, is a measure of the degree of hangingwall fracture. A correlation between predicted energy release rates and actual underground conditions in stopes in the O.F.S. goldfields has been encouraging enough to define parameters on which future stoping layouts can be based. The use of the elastic theory through the analogue has been extended to the assessment of the influence of stoping operations on off-reef excavations. Underground conditions at damaged and undamaged areas have been compared with predicted elastic stresses at the positions under review, resulting in the derivation of design parameters for use in siting off-reef excavations in the prevailing geological conditions in the O.F.S. and Klerksdorp goldfields. The analogue has also been used to assess the vulnerability of certain un mined dykes to bursting. Correlations between stresses induced on dykes by stoping and dyke behaviour underground has enabled critical stress levels to be determined for several persistent dykes occurring in the O.F.S. and Klerksdorp goldfields. A number of long and short term planning projects at mines operating in the Anglo American Corporation and General Mining and Finance Groups are described, where the data derived from the electrical resistance analogue is processed by computer programmes and assessed on the strength of the design factors derived from the correlation of field work and the elastic theory.

Jan 1, 1970

By More-O&apos, R. C. Ferrall, J. W. Wilson

Discussion: M. D. G. Salamon* (Fellow): The theoretical principles behind the techniques of calculation used by the authors was formulated and published during the period 1962- 65. These principles, together with their practical implications, were summarized in a review paper in 1966.1 Now, in February, 1970, we have this long and comprehensive paper discussing the practical application of the theory. I think this is good progress. The large number of practical examples treated in the paper clearly demonstrates not only the skill and knowledge of the authors, but also the versatility of the techniques of analysis. I feel that the techniques described by the authors, and their improved versions, will revolutionize mine planning. I suggest that no shaft system or stoping layout should be planned in future without an adequate rock mechanics analysis. It seems that it will be progressively more difficult to white wash mistakes in rock mechanics and attribute their costly outcome to normal mining risk. We should not, however, become complacent. There is still a lot to learn and do in the future. I do not want to discuss tonight the question of further research but instead, I will raise two other problems which may hinder the future progress of practical rock mechanics. To carry out work similar to that described in the paper, mine managements require men who are capable of doing the work and who have the most efficient techniques of analysis at their disposal. As a research engineer I have been associated with the development of techniques of analysis. I can assure you that these have undergone an amazingly rapid development during the last six years. We have seen the change from the use of the electrolytic tank analogue and manual integration to the method described by the authors, that is, to the employment of the automatic network analogue and computer integration. But this is not the end. In a recent paper Prof R. P. Plewman2 and his co-authors described a completely digital technique. Here the process of calculating on- and off-reef quantities is integrated into one computer run. But these sophisticated methods of computation are useless without men to make intelligent use of them. During the last few years a new breed of mining engineers has appeared on the scene - the Rock Mechanics Engineer. I feel it is timely to call the attention of the senior members of this Institute to the fact that this new breed will succeed in carrying out its duties in a valuable manner only if we manage to attract to its ranks young engineers of the right quality. The requirements are high. The top rock mechanics engineers have to be good mine planners and they have to understand the essence of sophisticated theories. Without these attributes they will not succeed in the long term and the industry will not gain the benefit of available knowledge. To attract this quality of engineers the industry will have to ensure that rock mechanics is accepted by all concerned as a career which could lead to the top echelons of our profession. Finally, I would like to make one or two remarks concerning Part I of the paper. In Sections 3.1 and 3.2 the authors describe methods of determining the normal stress on the reef plane and the convergence distribution in the excavations. The description as given applies only to a horizontal reef. When the reef is inclined the situation is more complex since a shear component of stress on the intact reef and a ride component in the excavations must then also be determined. These can be calculated by methods similar to that described in the paper.3 The practical application of the method of calculating the released energy (Section 3.4) is in the comparison of various stoping layouts to establish an order of preference in terms of decreasing rates of energy release. To carry out these comparisons effectively, the calculations must be carried out in a manner by which the values of energy per unit area obtained are comparable. I would like to note in this respect that the method of calculation given in the paper is valid without reservation only if there is no elastic contact between the hanging and foot walls in the mined-out area. If there is contact then the calculated energy values are correct only if the mined out area is increased in small steps during the analysis. My second point in this regard is concerned with the practical method of calculation as described in Sections 3.4 (ii)-(iii). Firstly, I would like to suggest that the energy calculation should be carried out, as far as possible, by using always the same scale on the analogue. Secondly, the reading of current on a pin should be followed by the removal of that pin to obtain the corresponding reading of potential. The product of these two values will be proportional to the energy released during the mining of the small area corresponding to that pin. The method suggested by the authors tends to mask possible danger points in the layouts, since they obtain an average value for a time period, say, for six months.

Publications on hard rock tunnel support design in the South African mining industry have originated primarily from the goldmines during the past 50 years. Little has been published to date on the platinum and chrome mines of the Bushveld Complex. This paper covers the search for a suitable design methodology for off-reef tunnels at Impala Platinum Mine, situated on the Western Lobe of the Bushveld Complex. The fall of ground accident statistics for off-reef excavations of the mine are presented and the available rock mass quality evaluation systems are reviewed. The Q-Tunnelling Quality Index (or Q-Index) is selected because it assesses the important driving factors behind falls of ground at Impala. Two off-reef excavations are evaluated using the Q-Index, and it is shown that minor modifications are required for implementation at Impala. It will take some time before support design throughout the mine is based on the outcome of proper geotechnical investigations based on the Q-Index. Widespread implementation of such support designs should help to solve the fall of ground problem in off-reef excavations while at the same time reducing support costs.

Jan 1, 2002

By I. Hague

Support liners for underground applications include steel and timber sets, meshing and lacing, screen/mesh, shotcrete and thin support liners (superskins). Over the past few years, major advances have been made in the design and application of liners; especially shotcrete and thin support liners. For shotcrete in mines these advances include the common use of slick-lines to solve logistics problems, the design of alkali free accelerators, the use of synthetic fibres and the new generation application equipment. The field of thin support liners is a new one but advances have been dramatic. This paper discusses the progress made and the need for standardization in definitions and testing for thin support liners. It concludes that the newer technologies have a huge potential positive impact on the industries, from both safety and cost points of view. Le chemisage de soutènement pour extraction souterraine comprend des cadres d’acier ou de boisage, mailles et chapeau, cribles/mailles, béton projeté et des chemisages minces de soutènement (super-peaux). Dans les dernières années, des progrès considérables ont été fait dans la conception et application des chemisages, en particulier les chemisages de soutènement en béton projeté et les chemisages minces. Pour le béton projeté dans les mines, ces progrès comprennent l’utilisation courante de lignes de minerais broyés fin pour résoudre des problèmes de logistique, la création d’accélérateurs sans alcali, l’usage de fibres synthétiques et d’une nouvelle génération d’outillage. Le domaine des chemisages minces de soutènement est très récent mais les progrès ont été rapides. Cette étude présente les progrès accomplis et discute du besoin de standardisation dans les définitions et les tests pour chemisages minces de soutènement. La conclusion est que les technologies nouvelles présentent un énorme impact potentiel positif sur les industries, du point de vue à la fois de la sécurité et de la rentabilité. Unterstützungsverkleidungen für Untertaganwendungen inkludieren Flecht und Seilwerk, Gitter/Geflecht, Spritzbeton und dünne Unterstützungsverkleidungen (superskins). Während der letzten Jahre wurden grosse Fortschritte im Design und in der Anwendung der Verkleidungen gemacht; besonders bei Spritzbeton und dünnen Unterstützungsverkleidungen. In Bezug auf Spritzbeton in den Gruben schließen diese Fortschritte den allgemeinen Gebrauch von Rutschbahnen ein um Logistikprobleme zu lösen, das Design von alkalifreien Akzeleratoren, den Gebrauch von synthetischen Fasern und die neue Generation von Anwendungsausrüstung. Der Bereich der dünnen Unterstützungsverkleidungen ist neu, aber die Fortschritte sind drastisch gewesen. Diese Arbeit behandelt den erzielten Fortschritt, die Notwendigkeit der Normierung in den Definitionen und in der Prüfung dünner Unterstützungsverkleidungen. Sie kommt zum Schluß, daß die neueren Technologien, sowohl vom Gesichtspunkt der Sicherheit als auch der Kosten, eine sehr große potentielle positive Auswirkung auf die Industrien haben.

Jan 1, 2003

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

By G. Dellas, R. Mangera, A. Voigt

"X-ray transmission (XRT) sorting has become the preferred recovery technology option in several parts of the diamond-winning flow sheet. In the De Beers Group, applications of XRT are found across kimberlite, alluvial, and marine operations. This is the result of intensive R&D conducted over the years to arrive at a suite of machine embodiments capable of sorting and auditing diamonds across all size ranges.The first applications in the marine environment used the technology in an auditing mode, and served as a useful early predictor of diamond content weeks ahead of sorthouse returns. The same machines are now available with ejection capability to produce high final product grades. The next application was tests on coarse alluvial gravels as an alternative to dense medium separation. The results were very encouraging, and tests are planned for both green- and brownfield kimberlite environments, as well as to explore an alternative to conventional techniques in final diamond recovery. At the Jwaneng mine Large Diamond Pilot Plant (LDPP), the objective is to recover diamonds in the size fraction –45 +25 mm.The technical challenge remains in the finer sizes, for high-capacitymachines as direct alternatives to conventional diamond recovery technologies. This is an area of ongoing R&D and it is only a matter of time before the breakthrough emerges. X-ray transmission fundementalsXRT makes use of X-ray imaging techniques to analyse objects and materials, and has a wide range of applications from baggage scanning for security purposes (Martz et al., 2016), to recycling of waste material (Owada, 2014). During the last decade XRT has been applied to an increasing extent in the minerals processing industry (von Ketelhodt and Bergmann, 2010; Sasman, Deetlefs, and van der Westhuyzen, 2018). Dual-energy XRT (DE-XRT), in which images of the target material are obtained at both high and low Xray energies, allows for elemental analysis and therefore can be used to discriminate between various minerals.A DE-XRT system makes use of a dualenergy X-ray line scan sensor to generate images of transmitted X-rays (Figure 1). Dualenergy refers to the camera, which contains two sensors, one responding to low-energy Xrays and one to high-energy X-rays. Feed material can be imaged either while on the belt, or while in flight."

Feb 1, 2019

By S. K. Murphy, K. B. Le Bron, A. K. Ward, S. Hayes, T. Rangasamy

A process for evaluating different options for extraction of mining blocks is presented. The process is described and an example of the application of the process to a case study is presented. Un procédé pour évaluer différentes options pour l’extraction de blocs d’exploitation est présenté. Le procédé est décrit et un exemple de l’application du procédé à un cas particulier est présenté. Ein Prozeß für das Auswerten der unterschiedlichen Optionen für die Extraktion von Abbaublöcken wird dargestellt. Der Prozeß wird beschrieben und ein Beispiel der Anwendung des Prozesses zu einer Fallstudie wird dargestellt.

Jan 1, 2003

By Bosman

Medium suspensions play an integral part in the successful application of dense medium separation for both static and dynamic separators. Although models exist to predict particle movement as a function of medium density and viscosity, these models have been derived on the assumption of Newtonian rheology. Viscosity measurements of medium suspensions have shown that they are non-Newtonian, with a yield stress, and as such cannot be used in the existing models. As a result, medium selection remains an art based upon practical experience and indirect measurements of viscosity such as stability and cyclone differentials.

Jan 1, 2014

By C. Atilla Öztürk

Determining the cutability and mechanical properties of rocks is vital for the feasibility studies of a mine or tunnel projects. Many scientists have investigated the correlation between these parameters in order to predict specific energy (SE) and other important rock cutability properties for many years. On the other hand, textural properties of rocks have been quantified in detail by Howarth and Rowlands (1987). Hence, it was possible to correlate mechanical and textural properties of rocks by using a parameter known as the texture coefficient (TC). The main objective of this study was to use the test results taken from a research project carried out by Bilgin and Shahrair1tocorrelate the mechanical and cutability properties of rocks with textural properties of rocks. For this purpose, uniaxial compressive strength (UCS), uniaxial tensile strength (UTS), cone indent or (CI),point load index (PLI), unit volume weight (?), porosity, SE, and normal and cutting force values, were correlated with textural properties of rocks. Hence it was possible to make illuminating interpretations about the relationships between the mechanical and cutability with the textural properties of rocks. Keywords: Cutting properties, mechanical properties, specific energy, texture coefficient.

Jan 1, 2004

By A. Kijko, C. W. Funk

Methods for the analysis of seismic hazards in mines are reviewed as illustrations of the techniques that are being used in some South African mines. The classical parameters that describe a hazard are the seismic activity rate, ?, the Gutenberg-Richter value, b, and, occasionally, the maximum regional magnitude, mmax The activity rate is calculated readily owing to the inherent simplicity of its definition. The evaluation method presented for the Gutenberg-Richter b value takes into account the presence of mmax Three statistical procedures are described for the assessment of mmax which the maximum observed magnitude, Xmax a crucial role. Often, the configuration of mine seismic networks is changed, or the networks are improved, which inevitably gives rise to changes in the completeness of the seismic catalogues. The routine analysis of seismic hazards must account for these time dependent changes. A method for the evaluation of hazards is reviewed that accommodates varying levels of quality in the catalogues. Finally, the concept of the volume of ground motion (VGM) is presented. This is a technique that allows for most aspects of seismic hazards in mines. The advantage of the VGM is that a hazard can be described by one physically significant value: the volume of rock (cumulated over a time period) in which the ground motion exceeds some critical particle velocity. Data from the gold mining region in South Africa known as the Far West Rand is used in a demonstration of the discussed methods of hazard analysis.

Jan 1, 1994

By J. H. van Dalen, P. J. Brandt, F. W. Wessels

A maximum of ten process streams (Merrill barren solutions) can be monitored sequentially with this on-line analyser, and gold concentrations as Iow as 0,005 mg/I can be determined. The design is a further development of the Tell-tale analyser constructed by the Corner House Laboratories during the period 1965-69. The barren solution is preconcentrated automatically by solvent extraction, the solvent being a solution of I per cent Aliquat 336 in di-isobutyl ketone. An aqueous-to-solvent ratio of 40: I is maintained. The extracted gold in the organic phase is determined by flame atomic absorption, each analysis taking approximately II minutes. The long-term reproducibility of the absorbance readings over a 24-hour period of repetitive sampling of four simulated process streams varied from 6,9 to 4,1 per cent relative standard deviation for gold concentrations of 0,0 I to 0,05 mg/I.

Jan 1, 1980

By A. Mitchell

On 25 August 2011, Andrew Mitchell, Lucas Moalusi, and Matthew van der Want of Bell Dewar hosted a presentation on Mining and Communities in Mooinooi, in the North-West Province. The conference was attended by traditional leaders in the North-West Province, officials from the Department of Local Government and Traditional Affairs, and executives from the mining industry. The presentation concerned traditional governance in mining, communities? rights in terms of applicable legislation, and the corporatization of community affairs.

Jan 1, 2012

By Org de Wet

This paper summarises the strategy for selection between a two module coal plant incorporating large, but less equipment, and a three module coal plant with more but smaller equipment. The two options were evaluated in terms of three main categories: ? Size ? size of the equipment and the effect on the process efficiency as well as the difference in physical dimensions of the plant to accommodate the larger equipment; ? Cost ? capital savings between a two and a three module plant, processing the same ROM (run-of-mine) tons per hour (t/hr); and ? Practicality ? in terms of constructability of the plant, safety of using larger equipment and maintainability of the equipment. Decisions that were taken to reduce the risk associated with size, cost and practicality on the chosen option of a two module plant will be highlighted.

Jan 1, 2006

By A. A. Bradley, K. H. Stanton, P. J. D. Lloyd

A theory for the dynamic balancing of centrifugal mills is presented that takes account of the mass and shape of the charge in a gyrated grinding tube and the way in which the charge lags behind the centrifugal force vector. predicts that a corresponding lag in the angular position of the counterweight centres of mass is necessary, and that the fractional filling should be increased if the ratio of gyration diameter to tube diameter is decreased. A worked example is given for a I MW centrifugal mill that was balanced adequately by the methods described.

Jan 1, 1983

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived ?resource converted to reserve? area, (which is based on the business plan from CADSMine?), versus the ?resource available for mining?, (which is derived from Datamine?), underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2012

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically, the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived 'resource converted to reserve' area (which is based on the business plan from CADSMine?) versus the 'resource available for mining' (which is derived from Datamine?) underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2013

By L. S. Belyayeva, A. S. Chumak, N. N. Boyko, A. V. Bondarenko

Analysis of results of many years concerned study of the fire hazard parameters of the material of the mine conveyor belts come in for use at the mines of the Ukraine in 1984-2002 that was carried out in the laboratories of the Scientific-Research Institute of Mine-Rescue Work is adduced in the paper. The basic tendencies on raising the fire safety of the conveyor belts that are retraced in their world production are shown.

Jan 1, 2003

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015