Search Documents

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

The relationships between backfill-transportation parameters (solids concentration, velocity, and pipe diameter) and the wear rate of backfill-transportation pipelines is well understood. However, the degree of wear experienced by a pipeline depends not only on the transportation parameters, but also on the characteristics of the solids making up the backfill, i.e. the particle-size distribution, hardness, shape, and sharpness of the particles. Therefore, unless data corresponding to the specific wear rate of the solids are available, the determination of the wear rate for pipes transporting an uncharacterized backfill is largely guesswork. This paper describes an evaluation of particle characteristics with special reference to particle sharpness so that pipe wear rates can be correlated with solids of different size distributions and sharpnesses.

Jan 1, 1993

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By N. Mangesana

The effect of high solids concentration and coarse particle sizes (d50 ranges 90?300 µm) on the viscosity of a suspension of water and silica sand was investigated. The experiments were designed to include conditions that have been tested by other authors and those encountered in the operation of tumbling mills. The rheological data was measured using a tube rheometer with operating pseudo shear rates of up to 1500 s-1. The rheograms obtained depicted dilatant behaviour. The Otswald-de Waele, Bingham, Herschel-Buckley and Casson models were fitted to the experimental data. The Herschel-Buckely model, which approximates the yield point and gives an indication of the shear thinning or shear thickening behaviour of the suspension, was found to provide the best description of the flow curves for all slurries. The Herschel-Buckely model was then used to determine the apparent viscosity of all the tests. The apparent viscosity and yield stress increased with solids concentration and particle size at the different pseudo shear rates. The increase in slurry viscosity with solids concentration was attributed to increased frequency of particle-particle interactions. The increase in slurry viscosity with particle size was attributed to increased inertial effects. At low shear rates the sand slurry exhibited shear thinning behaviour for all solids concentrations. At higher shear rates above 1000 s-1the high solids concentration suspensions exhibited a transition from shear thinning to a shear thickening behaviour.

Jan 1, 2008

By N. Wagner, P. den Hoed, J. D. Steenkamp, S. Soqinase

In pyrometallurgical processes, metal oxides are reduced from molten slag through carbothermic reduction. It is of interest to evaluate the reactivity of the carbonaceous materials towards substances such as slag. Characterization techniques such as coal petrography can provide insight into the influence of feed coal properties and how they potentially dictate reductant performance. This study aimed to compare the petrographically determined organic composition of coal to reductant reactivity. Two South African medium-rank C bituminous coals and one anthracite sample were investigated together with high-carbon ferromanganese industrial slag. The reductant reactivity tests were conducted at 1500°C in a muffle furnace to assess the potential of carbonaceous reductant in reacting with the main slag components. SEM-EDS was applied to understand the extent of MnO (and to a lesser extent, SiO2) reduction from the slag. Coal 2, consisting of a greater proportion of vitrinite (59.5 vol% on a mineral matter-free basis and 54.7 vol% including mineral matter) was the most reactive reductant. The anthracite sample, with the highest inert maceral proportions (71.8 vol% including mineral matter and 76.8 vol% on a mineral matter-free basis), was the least reactive reductant.

Feb 6, 2023

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By J. A. Wates

Stope backfilling in South African gold mines uses the coarser cyclone fraction of the gold tailings. The disposal of the overflow from the cyclones, which is finer and of higher moisture content than normal gold tailings, presents some problems. This paper describes an investigation undertaken to define the parameters that are required for a quantitative and qualitative assessment of the operation and stability of slimes dams built of such material. However, seeing the investigation was conducted on the slimes from only one mine, it is recommended that, until a wider range of data becomes available, tests should be conducted for each individual mine.

Jan 1, 1988

By B. Z. Weiss, N. R. Comins, F. Blum

Some aspects of the mechanical behaviour of chromium-containing dual-phase 3CR12 steel were investigated as a function of the temperature and strain rate. The yield stress was found to depend on both the temperature and the strain rate, with no substantial differences between the longitudinal and the transverse directions. The strain-rate sensitivity decreased with increasing temperature. The yield stress could be presented as a function of a temperature-strain-rate parameter. Impact test results showed substantial differences between the energy absorption of the transverse and longitudinal specimens above the ductile-brittle transition temperature. Changes in energy absorption with temperature were gradual for specimens in both orientations, and the transition from ductile to brittle behaviour occurred between 373 and 173 K. Strain rates ahead of the tip of notches with different geometries were calculated and measured experimentally.

Jan 1, 1990

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By G. A. Slabbert

The paper describes work undertaken to identify the influence of the matrix structure on the metal dusting rate of stainless steel alloys. Specifically, the difference in metal dusting rate between austenitic and ferritic stainless steels of similar chromium contents was investigated. The alloys were exposed to metal dusting conditions and their performance compared by weight loss, optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and Raman spectroscopy. The specific gas mixture used for all the tests were 18.9% CO-79.1% H2-2% H2O at 650°C. For austenitic stainless steels, Types 304, 321, 316, and 316Ti were compared to two ferritic grades, namely Types 430 and 441. The resistance of the ferritic grades was found to be significantly better than that of the austenitic grades. This was attributed to greater permeability of chromium through the matrix structure to maintain the protective oxide scale. The results will be used in the development of novel alloys to combat metal dusting.

Jan 1, 2013

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By P. R. Jochens, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace by A. A. HEJJA,D. D. HOWAT, andP.R.jOCHENS Published in the Journal March 1973. DISCUSSION R. E. Leyman* The authors discuss in detail the effects of transport and storage at the steel plant on the reactivity of lime as measured by the DIN Reactivity Test. They attribute the deterioration in reactivity to the absorption of water vapour and carbon dioxide, but make no mention of the possible role of atmospheric sulphur dioxide in this respect. The significance of the mineralogical and surface characteristics of gold grains in the recovery process by C. E FEATHER and G. M. KOEN Published in the Journal February 1973. AUTHORS&apos; REPLY TO DISCUSSION (Published in the Journal July 1973) H. P. Carlisle Mr Carlisle&apos;s questions and observations will be dealt with in the same order as they were raised. 1. How were the mass percentages of the grains determined from the sizes measured in polished section?

Jan 3, 1973

By M. Le Roux

The dewatering of coal, and particularly fine coal, continues to challenge coal prepatration engineers to find a cost-effective solution. With known world oil reserves being depleted daily, it is envisaged that the future price of coal may justify the use of thermal drying to achieve lower coal product moisture levels. The effect of exposure of the coal to elevated toemperatures on the mechanical strength of the coal was investigated. It was found that temperature does not play a major role in determining the volume breakage of a particle and that other variables such as orientation during impact has a much greater influence. A double breakage mechanism was reported during the grindability tests. Surface, as well as volume breakage, occurs for the first 4 minutes while only surface breakage takes place thereafter. Due to this double breakage action, it was found that exposure to temperature does play a role in the amount of breakage and breakage rates during grindability tests. It was also concluded that a particle will break to an optimum size due to impact, after which only its surface will grind away as it is subjected to breakage forces.

Jan 1, 2008