Search Documents

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

By S. M. H. Haddad, M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

Sulfide impurities in iron ore concentrates play an important role in designing pelletising and steel making plants. Therefore attempts are made to keep the sulfur content of the final concentrate produced by the plants as low as possible. Generally, in the beneficiation process of iron ore concentrate, the removal of sulfur is performed through magnetic separation systems, followed by reverse flotation. The sulfide content of the iron ore concentrates originated from two main sources, including pyrite and pyrrhotite. In this research, in order to compare the floating capability of these two types of sulfide minerals, two iron ore concentrates with different sulfide constituents, pyrite or pyrrhotite, were selected. Reverse flotation tests were done separately on these samples under similar conditions. Process parameters considered for the tests included pH (2, 4, 6, 8 and 10), collector consumption (150, 200, 250, 300 and 350 g/t) and frother consumption (40, 50, 60, 70 and 80 g/t). Potassium Amyl Xanthate (PAX) and Methyl Isobutyl Carbinol (MIBC) were the collector and frother used in the tests, respectively. For modelling and optimising process parameters, the Central Composite Design (CCD) method was applied to the test results. Empirical coded equations were obtained for responses involving weight recovery, Fe recovery, Fe grade and S grade. Finally, comparison of test results revealed that the elimination recovery of pyrite sulfides was far greater than pyrrhotite sulfides, and it was possible to remove 84% sulfur content of the pyrite sample compared to minus 30% for the pyrrhotite sample. Keywords: Reverse flotation, pyrite and pyrrhotite, sulfur removal, iron ore concentrate, beneficiation plant

Jan 1, 2020

In order to test the applicability of elastodynamic codes in the modeling of mining related problems, comparisons are made between seismic data and numerical analyses. The dynamic finite difference program WA VE is used for the modeling of a horizontal stope in a deep mine. The slip along a vertical fault situated within the positive excess shear stress lobe of the stope initiates seismic waves. The stope-fault geometry is modeled in both two and three dimensions. The three dimensional non-slip weakening WAVE analyses correlate well with Brune's analytical model. For accurate modeling of the peak particle velocities predicted by McGarr's empirical relationship, it is recommended that a three-dimensional stope -fault model is used, with the amount of slip weakening dependent on the magnitude of the event.

Jan 1, 1995

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RlOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. A Student Member who is in fulltime study at a university may submit the dissertation or thesis he has to write in part fulfilment of his university degree, provided that it is presented in a manner and on a topic suitable for publication in the journal. Entries for 1976 should reach the Institute by 31st December, 1976.

Jan 10, 1976

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

By J. Glazewski

The mining industry in South Africa has developed its own environmental guidelines in the form of an Aide-Mémoire1,which is an extension of the previous rehabilitation provisions to include all aspects of the environment and all phases of a mining operation. This development, at the time, recognized an international trend towards the formalization of environmental management in mining practice, which resulted from the realization of the large environmental liabilities that mines could face, particularly on closure. Over the past decade the international environmental focus in the mining industry has moved from operational management, to the reduction of liability on mine closure. Mine closure guidelines are being developed internationally by nations (for example, SRK, 19982) and by large mining groups (for example, Rio Tinto, 19983). In South Africa the Department of Minerals and Energy (DME) is presently reviewing the Aide-Mémoire to bring it in line with international and local developments and a separate mine closure plan is being considered.

Jan 1, 2000

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

By L. W. Palmer

Compositing or regularization of drillhole data is common practice in mineral resource estimation and is deemed a necessary step in producing unbiased estimates of mineral resources and reserves. Commonly, data are collected over irregular distances due to the varying relative thicknesses of lithologies drilled or sampling/assaying strategies. This necessitates data transformation to regular lengths of equal size to ensure that all data have the same sample support. However, there have been few detailed publications on the effect of this process on the composited data that are subsequently taken forward for the estimation process. In this paper, three currently available compositing methods are reviewed and the effects of inappropriate compositing methodologies presented. It is shown through a case study that compositing samples to different lengths leads to changes in the average and variance of the grades in the drillcores in the dataset, which will impact the final estimated value. These differences are exacerbated by breaks or gaps in data where, for a variety of reasons, there has been no data collection or data have been lost. The importance of appropriately treating blank and zero data is also presented. Globally, these differences might be minimal, but locally may be substantial, affecting the efficiency of the estimation and subsequent use of the results in, for example, mine planning and reconciliation. Further detailed investigation of compositing practices is required if the full implications of compositing are to be understood and any induced bias effectively defined.

Jul 10, 2024

By A. Rahmanab, A. Torpy, M. I. Pownceby, M. N. Zaman, N. Haque, W. Bruckard, J. Tardio

Ilmenite is the principal feedstock for producing TiO2 - used in paints, plastics and paper and the production of Ti metal. The Brahmaputra River system in Bangladesh represents a potentially new source of ilmenite concentrated within sandbar placer deposits and the current study presents results from beneficiation and characterisation studies conducted on Brahmaputra River Fe-Ti oxides. Characteristic of fluvial systems, the ilmenite concentration is low (~0.5 wt-%), however extensive annual dredging for waterway navigation provides the economic impetus to recover saleable ilmenite. The Fe-Ti oxide suite derived from magnetic fractionation comprises homogeneous ilmenite, titanohematite and hematite, although many grains exhibit complex exsolution within the (Ilm-Hem)ss series. The textural variability results in difficulty generating a pure ilmenite feedstock with the bulk concentrate typically being low in TiO2, containing 31.0 wt-%TiO2 and 62.7 wt-% (Fe2O3). Results are interpreted via an analysis of the implications for producing a commercial-grade ilmenite concentrate suitable for TiO2 production. Keywords: Ilmenite, titanohematite, Fe-Ti oxide exsolution, TiO2 production

Jan 1, 2020

By P. J. F. Fourie

The purpose and frequency of comprehensive performance testing and the types of tests to be included are discussed. The results obtained from a series of such tests are reviewed.

Jan 1, 1980

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

By S. K. Lahiri, K. C. Ghanta

Design of industrial slurry pipelines is usually performed by applying semi-empirical procedures, requiring a significant experimental study for each project. The mechanisms of suspension flow are not yet completely understood and existing predictive models cover only some aspects of uniform or closely graded particle slurry flows. This paper presents a computational technique for prediction of the velocity and concentration profile in slurry pipelines based on computational fluid dynamics. This model gives numerical solutions for the concentration and velocity distributions in the pipeline cross-section. The model prediction and experimental concentration and velocity profiles were found to be in good agreement. Keywords: pressure drop; concentration profile; particle diffusivity; slurry flow.

Jan 1, 2007

By I. E. Lane

Conventional demand management techniques invariably fail to offer optimum control flexibility in an operationally complex gold mining environment. An improved control system for electrical demand management is proposed. The system is designed to provide more effective load scheduling and control strategies by means of a computer aided demand management system (CADMS). The objective of the CADMS is to provide a responsive computational aid and adaptive control system for effective demand management. The system consists of a short term load forecasting module, an interactive load scheduling module, an incentive based electricity cost allocation module and a power management information module.

Jan 1, 1987