Search Documents

By N. J. Alderman, D. J. Clowes, N. I. Heywood

The effects were studied of the presence of comminuted flint on the rheological characteristics of chalk slurry pumped through a 92-km long pipeline from Kensworth Quarry to Rugby Cement Works in the UK, and their impact on the pipe flow conditions. Flow curves were measured for 63different chalk slurry samples; these were described by the Bingham plastic model. In addition to observing trends in the yield stress parameter and plastic viscosity in the model with variations in both flint concentration and dispersant additive, use was also made of slurry viscosity values at a reference shear rate of 60 s-1for the pipe flow. It was found that chalk slurry viscosity decreases with increasing flint content up to 10% by weight for a given additive concentration, and increases with increasing additive concentration from 0.7 to 1.0%, for a given flint content. The pipeline flow regimes were identified using the critical value of the Bingham Reynolds number for laminar flow breakdown. For Bench 11 (quarry bottom) chalk slurries, it was observed that all sections of the pipeline operate in the turbulent flow regime for the nine different formulations and for the three pipe diameters used along the pipeline. However, this was not always the case for Bench 1(quarry top) slurries. It was therefore recommended that chalk slurries prepared from Bench 1 should not be used because of the strong likelihood that laminar flow conditions will occur owing to the presence of higher clay concentrations within this bench. This, in turn, will lead to an unsafe operation of the pipeline because of the potential for coarse particle settling. Likewise, blending of chalk from Bench 1 with the lower benches such as Bench 11 could be problematic and this requires further experimentation.

Jan 1, 2007

By S. Banisi, S. Zare, M. Mahmoudi, M. Maleki-Moghaddam, M. Yahyaei

As the orebodies become more complex and lower grade, there is an increasing demand from crushing circuits for a finer product. When the product from a crushing circuit does not satisfy the requirements of the downstream processes, the cost of production increases. Thus, enhancing the performance of cone crushers through optimisation of their operating factors becomes important. One of the key factors affecting performance of cone crushers is the filling of the crushing chamber during the operation. The effect of varying the filling of the crushing chamber of a cone crusher was investigated. To assess the crusher performance, parameters such as crusher capacity, power utilisation, and reduction ratio were used. Extensive plant trials were conducted to obtain samples and operational data when the crusher chamber was 50% full (half-full) and 100% full, which is 300 mm above the top of the crusher chamber (super-choked condition). The results indicated a 62% difference in the crushing capacity when the crusher was operated in a super-choked condition compared to the half-full chamber level. In the super-choked condition, the size-specific energy at 12.7 mm was 20 % lower than that of the half-full condition. The Bond ball mill work index (BBWI) of crusher product indicated that the BBWI of the product of the super choked condition is 5.6% less than that of the product of half-full condition. This can be attributed to the generation of micro cracks in particles due to increase in the interparticle breakage when the crusher was operated in the super-choked mode. Keywords: Cone crushers, crushing efficiency, crushing chamber filling

Jan 1, 2020

By S. Mohanta, I. D. Behera, B. Sahoo

"Run-of-mine coal contains particles of different sizes with different specific gravities, and when this coal is crushed, the amount of material present in a particular density class changes. This alters the washability characteristics of the coal, which affects the quantity, quality, and separation efficiency of the gravity-based coal washing process. The degree of difficulty in washing a typical coal at a particular specific gravity depends mostly on the amount of material occurring within ±0.1 specific gravity range, which is known as ‘near-gravity material’ at that particular specific gravity of separation. In this paper, two numerical indices, namely ‘near-gravity material index’ and ‘index of washability’, are used to quantify the distribution of near-gravity material in different density classes and to evaluate the degree of difficulty involved in the washing process. The results of this preliminary investigation indicate the uniform distribution of near-gravity material in all density classes for finer size fractions, whereas for coarser size fractions more near-gravity material is present in the lower density classes, making the washing process more difficult at a lower specific gravity of separation. IntroductionThe prime objective of coal beneficiation is to remove physical impurities as effectively and economically as possible. The beneficiation process includes various operations on the asmined coal to make it more suitable for enduse application without destroying the physical identity of the coal. There are several coal beneficiation processes, but gravity-based separators remain the most efficient unit operation for removing the undesirable gangue material from run-of-mine coal. These separators exploit the difference in density between coal particles and gangue particles to effect a separation. The feed is introduced into an aqueous suspension of ultrafine magnetite with a particular density. The feed particles with a relative density less than that of the suspension (clean coal) float to the top surface of the suspension, whereas particles denser than the suspension density (gangue material) sink to the bottom. When the difference in density between the particle and the aqueous suspension is large, the separation is easy, but when this difference is less the separation becomes much more difficult since the settling velocity of the particles is very low. This lower settling velocity increases the probability that particles that should report to floats report to sinks, and vice versa, hence increasing the amount of misplaced material. Therefore, the degree of difficulty in beneficiating a typical coal at a particular specific gravity depends on the amount of material occurring within ±0.1 specific gravity range. This is known as ‘neargravity’ material, also termed ‘near-dense’ material, at that particular specific gravity of separation."

Jan 1, 2016

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

By H. A. Bilgin, A. Özgenog?lu, G. Kaçar

In this study, the influences of rock mass properties on the blasting performance in open cast mines are investigated. To this end, discontinuity spacings and discontinuity orientations are measured and full scale blasts with various designs are observed in open cast mines of Aegean Lignite (ELI) and Bursa Lignite (BLI) Establishments belonging to Turkish Coal Enterprises (TKI). For each blast, blasting cost is calculated, and particle size distribution representing the fragmentation of muckpile is determined by means of Split-Desktop software using image processing. 50%(K50), 80%(K80) passing sizes and topsize values are used in the determination of blasting performance according to rock mass properties. The relationships between orientation angle, which is the acute angle between the strikes of slope face and major discontinuity, and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of major discontinuity orientation on fragmentation and blasting cost. Furthermore, the relationships between discontinuity modal spacing (or block size index) and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of discontinuity spacing on fragmentation and blasting cost. In this paper, the trends observed in these relationships are discussed and the importance of it in mining is commented. Dans ce travail, Il a été traite les influences des qualites des rocheux massif sur les performances des abattages de l’excavation a ciel ouvert. Dans ce cas, les excavations a ciel ouvert dans les Entreprises Lignite d’Aegean et de Bursa qui appartient a La Societe Charbon de la Turquie; Il a été mesuré le trou du discontinuite et l’orientation du discontinuite et aussi, Il a été observé les abattages qui sont pareilles aux critaires exactes. Pour chaque abattages, Il a été fait le control des expences et la distribution du particle au dimension du pile qui a été deja abatté, a été trouve en utilisant le Software du Split-Desktop. Pour determiner les influences des qualites des rocheux massif sur les performances des abattages, Il a été utilisé K50, K80, et le plus grand valeurs des dimensions. Aussi pour determiner l’influence sur l’orientation du discontinuite majeur de la fragmentation et les expences de l’abattage, Il a été observé les relations entre l’angle de l’orientation ( C’est l’acutage entre la direction du banquette front et la direction du discontinuite majeur ) et les plus grand valeurs des dimensions et les expences de l’abattage. Plus, pour determiner des influences du trou du discontinuite sur l’abattage et la fragmentation; Il a été observé la relation entre l’index de la dimension du block et K50, K80 et les plus grand valeurs des dimensions et aussi les expences de l’abattage. Pour conclure; on peut dire que dans cette presentation, apres la discusssion des sujets consideres ces relations, Il a été souligné l’importances de ces relations dans la domain de la Minéralogie. In dieser Studie wurden die Einflüsse von Gesteinsmasse Eigenschaften auf die Sprengleistung in Tagebau Bergwerken untersucht. Zu diesem Zweck wurden Diskontinuität Abstände und Diskontinuität Orientierungen gemessen und Sprengungen im Originalmaßstab mit verschiedenen Anordnungen in Tagebau Bergwerken der Ägäischen Braunkohle (ELI) und Bursa Braunkohle (BLI) Betrieben, die zu der Türkischen Kohlegesellschaft (TKI) zugehörig sind, beobachtet. Für jede Sprengung wurden die Sprengkosten berechnet und die Teilchengrößenverteilung zur Darstellung der Aufteilung von Haufwerk ist durch Mittel von Teilbelegungssoftware, das Bildverarbeitung verwendet, bestimmt worden. 50% (K50), 80% (K80) durchlaufende Größen und Spitzengröße Werte wurden zur Bestimmung von Sprengleistung geordnet nach Gesteinsmasse Eigenschaften benutzt. Die Beziehungen zwischen Orientierungswinkel, welches der scharfe Winkel zwischen den Streichen der Hangfläche und Hauptdiskontinuität ist, und 50% (K50) und 80% (K80) durchlaufende Größen und Spitzengröße Werte sowie Sprengkosten wurden untersucht, um die Einflüsse von Hauptdiskontinuität Orientierung auf Aufteilung und Sprengkosten zu analysieren. Außerdem, wurden die Beziehungen zwischen Diskontinuität modal

Jan 1, 2003

By M. Nduna

Surface properties of metal sulphides have a great significance in various areas of engineering and science, such as acid mine drainage, contaminant sorption, and metal separation. In various attempts at producing metal sulphide particles from synthetic solutions, prodigious quantities of nuclei that grow only to colloidal dimensions have been frequently reported. This copious nucleation is promoted by the high levels of supersaturation that characterize most precipitation reactions. Colloidal particle formation in precipi¬tation-based separation processes results in sub-optimal solid-liquid separation, which is alleviated by the production of more highly crystalline particles or agglomerates. The current work approaches this challenge from an electrochemistry perspective, by measuring surface charge potential of precipitant particles during metal sulphide precipitation with respect to the concentration of metal sulphide lattice ions in solution. Electrophoresis was used to measure the metal sulphide particle zeta potential and the settling properties were obtained by performing settleability measurements using an Imhoff settling cone. A suspension of copper sulphide particles was precipitated from synthetic solutions of copper and sulphide ions at equimolar concentrations. Immediately after precipitation the copper sulphide particles had a zeta potential of -50 mV and a settleability of about 7 ml.l-1. With the addition of copper ions the settleability increased by a factor of nearly three times and the zeta potential also increased to a maximum of -40 mV. A decrease in zeta potential to a minimum of -60 mV was observed after the addition of sulphide ions and this was associated with a settleability of 0 ml.l-1.

Jan 1, 2013

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

Blaine number has long been used to evaluate the pelletising ability of iron concentrate in the industry. Much information and practical data are available about the effect of Blaine number on pelletising efficiency of different concentrate types. But not many researchers have focused on the effect of Blaine increasing method on pelletising behaviour of coarse concentrates. In this paper the effect of two different grinding methods (i.e. HPGR and Ball Mill) on physicochemical properties of coarse magnetic concentrate green and fired pellets were investigated. Microstructural studies by Field Emission Scanning Electron Microscope (FESEM) showed that the concentrate for which the Blaine number had been increased through HPGR grinding, has flake-like morphology. In contrast, increasing the Blaine number through ball mill grinding results in more granular particles. Two samples were prepared using HPGR and ball mill. The Blaine number of the HPGR product and ball mill product were 900 cm2.gr-1 and 1200 cm2.gr-1 respectively. The results revealed that pellet properties of this HPGR product are comparable to that of the ball mill product; this is due to the fact that the flake-like morphology leads to enhanced pelletising performance of coarse magnetite concentrates. Keywords: Iron pelletising, Blaine number, HPGR, ball mill, coarse particles

Jan 1, 2020

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023

By S. M. Bradshaw

In order to assess the requirements for online matching when using a transverse electric field (E-field) applicator to treat mineral ores continuously, the effect of varying load properties on matching has been investigated by simulation. The effective permittivity of the ore to be treated is expected to show variation on both short (< 1 s ) and long (minutes) time scales. By modelling the ore as a series of slices with alternating effective permittivity values, it was shown that permittivity variations on the scale of the expected particle size are attenuated significantly and matching is not required. For variations in permittivity on the length scale of the free-space wavelength, variations in reflected power are at most within ±10% of the mean. This is not considered operationally significant, as extreme permittivity variation over this length scale is unlikely, given the expected distribution of ore particle sizes to be treated. At typical ore transport speeds through the applicator, these variations occur on a time scale an order of magnitude shorter than the response time of typical industrial online matching equipment. This implies that online matching is neither required nor possible for short time scale variation. Long-term variations in dielectric properties can be adequately compensated for by current matching technologies. It is concluded that the transverse E-field applicator is robust to changes in the dielectric properties of crushed ores within the expected range of their variation.

Jan 1, 2012

By P. G. Toledo, R. I. Jeldres, G. R. Quezada

Chile is the main producer of copper in the world and lately the mining industry has suffered challenges due to the lack of water in the north of the country, along with the new policies of not using fresh water for the industry. This has prompted the use of seawater as an alternative source for mining. Several studies have been driven due to this new scenario, which have shown that seawater can be beneficial, if certain ions are removed from the process. This is the Mg that generates precipitates at high pH, that have been shown to make mining operations difficult. In particular, thickening operations are impaired by the presence of Mg ions, where aggregate formation and sedimentation decreases substantially. Our studies suggest the competence of the precipitates in adhering to the polyacrylamide (HPAM) flocculant and not towards the surface of the quartz minerals. This motivates the present work to use molecular dynamics to study the adsorption of a HPAM molecule on quartz surfaces and the surfaces formed by Mg precipitates. The surfaces are immersed in a saline solution or seawater that includes the HPAM molecule. Results are obtained by measure the adsorption frequency and duration. We obtained that the HPAM molecules are preferably absorbed on the surfaces of magnesium hydroxide. This gives us a good agreement with what is observed experimentally and strengthens the premise of the competition of hydroxide with the flocculant. Keywords: Molecular dynamics, adsorption, tailing flocculation, magnesium removal

Jan 1, 2020

By C. M. Sellars, W. E. Stumpf

SYNOPSIS The effects of concurrent recovery, prior creep deformation and concurrent high temperature fatigue on the coarsening of some carbides in steels have been studied. It was found that concurrent recovery enhances the coarsening rate by orders of magnitude and prior creep deformation causes an enhancement of about two times. Finally, concurrent fatigue causes an initial greatly enhanced coarsening rate but after prolonged cycling dissolution of the carbides occurs.

By R. Boom, J. Halder, B. Snoeijer, B. Deo, A. Overbosch

Operational data of BOF and the slag samples for different starting conditions of phosphorus(0.06–0.26 per cent P) and silicon content (0.3–1.2 per cent Si) of hot metal have been analysed. The contribution of parameters that are well known to affect phosphorus distribution at tap, like basicity, temperature, FeO content of slag, slag mass etc., is investigated through the models of ionic theory of slag, optical basicity, regular solution approach and molecular theory of slag. The best overall results are obtained by the model based on molecular theory of slag in which several operational parameters are also incorporated. The investigations of different slag samples, based on optical, SEM, EPMA and X-ray studies, reveal the effect of MgO and Al2O3on slag morphology and phosphorus distribution in different phases. It is important to consider phosphorus distribution ratio in the solid and liquid part of slag. The solid part of slag, which is mostly dicalciumsilicate, can contain up to 5 per cent phosphorus. The phosphorus content of the liquid part of slag may depend upon the phosphorus content of hot metal or phosphorus load of slag. It is found that incorporation of effect of dicalciumsilicate in the model improves the accuracy of prediction. For better process control, the addition of iron ore towards the end of blow must be avoided while treating high phosphorus hot metal or during the production of ultra low phosphorus steels. Keywords: steelmaking, BOF, phosphorus distribution, slag morphology, MgO, Al2O3,dicalciumsilicate, process control, models

Jan 1, 2004