Search Documents

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

By K. Gharibi, A. Dehghani, S. Farrokhpay, M. Aghajanloo, M. Ostadrahimi

The effect of flotation operational parameters on froth stability and froth recovery was studied. Froth stability was measured using a special column. To determine the froth recovery, the froth height change model and froth height exponential model were used. It was found that since the interactions between the pulp and froth zones affect the time of froth formation, the exponential model is more suitable than the froth height change method for determining the froth recovery. The results showed that superficial air velocity and collector dosage have, respectively, the highest and lowest effect on the froth recovery, while froth recovery decreases sharply with increasing froth height.

Jan 1, 2021

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By R. L. Setsepu, S. O. Bada, J. Abdulsalam

The utilization of biomass as a solid fuel for co-firing has received great attention from boiler manufacturers as a clean coal technology (CCT) option. This research aimed to produce biocoal pellets, as a clean energy fuel, using hydrochar from trees planted to rehabilitate acid mine drainage (AMD) water and fine coal discards. The hydrochar was synthesized by hydrothermal carbonization of Searsia lancea harvested from AMD-contaminated land at a temperature of 280°C and a residence time of 90 minutes. It was blended with discard coal (–1 mm) at ratios of 25% and 50% hydrochar to produce different forms of solid pelletized biocoal (BC). The physicochemical and mechanical properties of each of the biocoal pellet blends were determined. The 100% hydrochar had the highest calorific value of 29.99 MJ/kg, while the raw discard coal had a calorific value of 16.73 MJ/kg. The ash content decreased from 42% in the discard coal to 25% in the blend of 50% coal and 50% hydrochar biocoal pellets. Biocoal pellets comprising 25% hydrochar and 75% discard coal (BC25 HC/75 COAL) displayed the best mechanical properties (compressive strength 3.06 MPa) of all the fuels, but the physicochemical properties were inferior to the BC50 HC/50 COAL pellets. This research has demonstrated that hydrochar synthesized from a tree species planted for hydraulic control of AMD has the capability to act as a binder for improving the mechanical properties and energy characteristics of fine discard coal.

Dec 1, 2021

By D. Xie

An in situ gravimetric technique based on wetting and capillary action principles has been used to investigate the wetting and penetration of synthesized alumina samples and commercial magnesia spinel refractories by CaO-SiO2-Al2O3-Fe2O3slags. Synthetic slags of 40CaO-40SiO2-20Al2O3 (in weight per cent) with 0 to 9 weight per cent Fe2O3were used and the experiments were conducted at temperatures 1370 to 1470ºC under argon. The contact time between the sample and the slag was 30 minutes. The results show that the wetting and penetration are enhanced by the iron oxide addition in the slags. Addition of Fe2O3from 0 to 9 weight per cent resulted in a significant increase in the slag penetration into the magnesia spinel refractory by a factor of about 7 and a moderate increase in the synthesized alumina by about 60 per cent. The addition of Fe2O3enhanced the wetting (??cos?, where ? is the surface tension of the slag and the contact angle between the slag and the refractory) by 5 to 18 per cent. An increase in temperature from 1370ºC to 1470ºC resulted in a significant increase in the penetration of a 6 weight per cent Fe2O3slag in the alumina and magnesia samples by a factor of4 to 5 and a decrease in wetting by approximately 30 per cent. Keywords: refractories, slag penetration, wetting.

Jan 1, 2004

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By X. B. Zhao, J. G. Cai

When stress wave propagates through fractured rock masses, the wave will be slowed and attenuated due to the presence of these fractures. If the amplitude of stress wave is large enough to mobilize nonlinear deformation of these fractures, they will present different effects on one-dimensional P-wave propagation compared with those of linear deformational fractures. The static BB model is adopted to describe the nonlinear deformational behavior. Method of characteristics combined with displacement discontinuity theory is used to build analytical solutions of wave particle velocities and wave stresses. These equations are numerically solved with sufficient accuracy.

Jan 1, 2003

By M. Tang, X. Tong

"SynopsisSlime coating is one of the most common ways for serpentines to contaminate metallic mineral concentrates during traditional flotation of coarse sulphide particles. This could pose quite a complicated and challenging problem in the case of some types of low-grade and finely disseminated Cu-Ni ores bearing high serpentine contents. This is the case for the copper and nickel sulphides from the Yunnan Mine, China. Previous batch flotation tests of this ore resulted in satisfactory recoveries of 86.92% Cu, 54.92% Ni, and 74.73% Pt+Pd, and concentrate grades of 4.02% Cu, 3.24% Ni, and 76.61 g/t Pt+Pd. However, the MgO content in these concentrates was more than 19%. In the current study, microflotation tests and settling rate tests were introduced to investigate the effects of a combination of strong collectors (a 2:1 weight ratio of butyl xanthate and butyl ammonium dithophosphate) on entrainment of serpentines in metallic mineral concentrate, as well as visual observations of the concentrates in suspension using still photography. All test results indicated the presence of serpentines entrapped in the hydrophobic flocs that resulted from these collectors, even with the use of effective gangue depressants. These strong collectors are used to flocculate the ultra-fine sulphides by forming loose and ‘fluffy’ hydrophobic flocs. However, these hydrophobic flocs may also be able to load or entrap some serpentine slimes into the concentrate, and this entrained serpentine could be harder to remove by using depressants or intensified conditioning than serpentine slime coating on the particle surfaces.IntroductionSerpentine minerals, which have the generalized composition (Mg,Fe)3Si2O5(OH)4, can be easy to crush and grind due to their convoluted and bent layered structures. These serpentines can hinder the enrichment of some metallic minerals and dilute their concentrates by entrainment during flotation. The resulting high pulp viscosities, slime coatings, and high content of dissolved ions adversely affect the flotation recoveries of copper and nickel sulphides, and high levels of MgO entrained in the concentrates lead to heavy penalties from smelters. Since the quality of nickel flotation concentrate depends heavily on its MgO content (generally less than 6–7% for No.1 or 2 grade nickel concentrate according to the standard requirement from National Nonferrous Industry), reducing the entrainment of serpentine during flotation is becoming more and more pressing. Previous research has focused on the collectors and depressants that are commonly used in copper-nickel flotation, as well as their interaction mechanisms."

Jan 1, 2015

By J. van der Merwe, C. Phetolo, V. Matjeke

The mechanical properties and microstructure of AlSi10Mg alloy samples that were printed by selective laser melting (SLM) were studied to determine the effect of processing parameters and building orientation. After printing, the alloy was stress relieved at 250°C for 2 hours. The microstructures were analysed by optical microscopy and scanning electron microscopy (SEM) to determine the alloy phases and distribution. Phase transformation characteristics of the material were evaluated using differential scanning calorimetry (DSC). Mechanical properties were determined by subjecting the XY- and Z-built samples to tensile and nano-indentation testing. The samples from the tensile tests were then used to perform fractographic analysis by SEM. The microstructural properties in each orientation revealed a non-homogeneous microstructure which was characterized by a semi-elliptical tract and fine silicon precipitates, which were found to be softer along the fusion zone. The DSC thermograms revealed that the material underwent two phase transformations during the first heating cycle. The mechanical properties revealed a higher UTS, higher yield strength, and a lower percentage elongation in the Z orientation than in the XY orientation. Fractographic analysis showed that crack initiation in both orientations started from the surface in a brittle manner due to surface flows, and then propagated via microvoid coalescence.

Jul 1, 2021

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By M. Asghari, R. Amiri, A. Haratian, M. Noue Parast, S. Haji

Today the roller screen has a wide range of applications in the steel-making industry. It is used for screening of green pellets before using the kiln. Since the appropriate size of a green pellet is -16+9 mm, there are different gaps between rollers that make green pellets classified in three categories: -9 mm (undersize), -16+9 mm (onsize) and +16mm (oversize). The efficiency of a roller screen is specified according to the weight percent of undersize in onsize as a fine material, and weight percent of onsize in oversize (loss). This efficiency is influenced by different operational parameters such as roller diameter, roller speed, and roller gap, material type of rollers and inclination of roller screen. This study investigates the effect of different material types of rollers in efficiency of Ardakan roller screens, located in the Yazd province of Iran. The rollers of the existing roller screens in this pelletising plant are made of polyurethane which according to this investigation, has a maximum lifetime of about six months. Operating the polyurethane rollers beyond its lifetime generates serious problems such as high wear of rollers, and consequently, material buildup on the roller surface which then significantly decreases the roller screen efficiency. So, after examining different roller materials, stainless steel 304 with higher surface roughness to help pellets move properly on the roller screen surface was selected as a solution to this problem. The new roller screen was constructed by Fakoor Meghnatis Spadana (FMS) and replaced the previous one. In this way, the maximum capacity of the roller screen was increased about 17% and the roller screen efficiency was increased about 15%. Keywords: Roller screen, green pellets, efficiency, onsize, operational parameters

Jan 1, 2020

By M. Gao

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By A. Mabentsela

A furnace freeze lining is necessary for safety and economic reasons in several smelting operations. The integrity of the freeze lining is put at risk by furnace power imbalances. Although numerous models have been derived to model the growth and depletion of the freeze lining due to power imbalances, no model exists for thermomechanical damage to the freeze lining. This study provides an initial pathway for modelling thermomechanical damage to the freeze lining in an ilmenite smelting furnace using information from the literature and experimental work. A methodology under the framework of continuum damage mechanics is proposed to model mechanical damage to the freeze lining due to phase changes, thermophysical changes, and constrained thermal expansion. Drill cores of solidified slag ingots were used to represent the freeze lining. The modified power law proved to be the best predictor of the softening response of the drill cores. Damage driving parameters were extracted from the raw data, and governing equations of the parameters with respect to temperature were derived for use in a finite element method (FEM) code.

Jan 26, 2023

By A. Golshani, M. Oda, K. Suzuki, T. Takemura

Anisotropic behaviours of OhshimaOshima granite were investigated by carrying out uniaxial compression tests, together with observations of microcracks under an optical microscope. The elastic modulus tensor of Oshima granite at 10 per cent strength,E10, were calculated using theoretically formulation of elastic modulus tensor in terms of the second-rank crack tensor for pre-existing open microcracks. Furthermore, with the assumption of orthorhombic elasticity, the nine moduli of Oshima granite E10were determined by uniaxial compression test. Twenty-onemoduli of samples, calculated without assuming any symmetry, also showed orthorhombic features. Direction of the symmetry axes agreed well with the orientation of preexisting cracks. Comparison of crack tensor-based formulation results with the experimentally determined one show that the anisotropy of elasticity of Oshima granite is caused by pre-existing open microcracks, not by pre-existing healed microcracks and also crack tensor formulation can be used, as a first-order approximation at least, to describe the anisotropy of Oshima granite induced by pre-existing open microcracks. ZUSAMMENFASSUNG: Das anisotrope Verhalten des Oshima-Granits wurde mit Hilfe voneinachsigen Kompressionstests und durch die Betrachtung von Mikrorissen unter einem optischenLichtmikroskop untersucht. Das Elastizitätsmodul von Oshima-Granit bei 10 Prozent Kraft E10wurde berechnet, indem man die Formulierung des Elastizitätsmodultensors, ausgedrückt alsRisstensor zweiter Ordnung theoretisch auf bereits existierende Mikrorisse angewandt hat.Außerdem wurden die neun Module des Oshima-Granits unter der Annahme orthorhombischerElastizität E10mit einem einachsigen Kompressionstest bestimmt. Einundzwanzig Stichproben,die ohne die Annahme irgendeiner Symmetrie genommen wurden, zeigten ebenfallsorthorhombische Merkmale. Die Richtung der Symmetrieachsen stimmte mit der Orientierungbereits vorhandener Risse überein. Der Vergleich der Ergebnisse der auf dem Risstensorbasierenden Formulierung mit der experimentell bestimmten Formulierung zeigt, dass dieAnisotropie der Elastizität von Oshima-Granit von bereits vorhandenen offenen Mikrorissenverursacht wird, und nicht von vorhandenen vernarbten Mikrorissen, und dass dieRisstensorformulierung auch zumindest für eine Annäherung erster Ordnung benutzt werdenkann, um die durch vorhandene offene Mikrorisse induzierte Anisotropie des Oshima-Granits zubeschreiben. RESUME: Les comportements anisotropes du granit d’Oshima ont été étudiés en réalisant destests de compression simple, et en observant les microfissures au microscope optique. Le tenseurdu module d’élasticité du granit d’Oshima sous une résistance de 10 pourcents, E10, a été calculéen se servant de la formule théorique du tenseur de module d’élasticité basé sur le tenseur defissures de second ordre des microfissures ouvertes préexistantes. En outre, sur base del’hypothèse de l’élasticité orthorhombique, les neuf modules du granit d’Oshima ont étédéterminés par des tests de compression simple. Vingt et un modules d’échantillons, calculés endehors de toute hypothèse de symétrie, ont aussi montré des caractéristiques orthorhombiques. Ladirection des axes de symétrie correspondait bien à l’orientation des fissures préexistantes. Lacomparaison des résultats de la formule basée sur le tenseur de fissures avec les résultatsdéterminés expérimentalement montrent que l’anisotropie de l’élasticité du granit d’Oshimaprovient des microfissures ouvertes préexistantes, et non de microfissures préexistantes referméeset que la formule du tenseur de fissures peut servir, au moins comme première approximation, àdécrire l’anisotropie du granit d’Oshima marqué par des microfissures ouvertes préexistantes.

Jan 1, 2003

By J. A. Bakken, T. Magnusson, G. Sævarsdottir

This paper describes measurements of current and voltage done on submerged arc furnaces. The aim is to focus on and attempt to separate from one another the electric arc current and the current bypassing the arc through the charge. Toward this goal two measurement campaigns on AC-arcs burning on coke beds are ac-counted for. The first was done on a 150 kVA pilot furnace at SINTEF in Trondheim Norway, and the second one was done on a 48 MVA industrial furnace run by Icelandic Alloys in Iceland. The measurements were compared to simulations employing an advanced MFD arc model. The main results are that a coke bed does not necessarily behave as a linear conductor. However the warmer chemically transformed part of an operating Si-metal or FeSi furnace probably exhibits linear behaviour and passes a considerable fraction of the phase current, perhaps on some operating conditions, as much as 50%.

Jan 1, 2007

By P. J. Petit

The strategic mission of the South African mining industry is to extract the mineral assets in an energy efficient, economical and safe manner. Drilling has received particular attention in the last few years. As the operations move away from the power source, conventional and old drilling technology result in poor penetration rates, increased drilling shift lengths, slow face advances and limited stope efficiencies. The need for an alternate mining method, performed by a skilled workforce, to increase productivity, has led to the development of the electric rock drilling system for in-stope mining operations. The focus of this paper is a systematic evaluation of the electric rock drilling system as a function of production and technical parameters, in the platinum orebody. The particular electrical reticulation system is illustrated. Power usage, problems experienced, and solutions are described. The safe use of the recently developed drill is elaborated upon by describing protection devices. The testing and certification process, for approval by the recognized authorities, are documented. The testing and certification process, for approval by the recognized authorities, are documented. The human factor is also considered. Known detrimental factors of high noise exposure, vibrations levels and oil emissions are reviewed. In conclusion, recommendations on future strategies for the implementation of electric drilling technology within the mining and construction industries, is included.

Jan 1, 2006