Search Documents

By G. J. van Tonder

The use of Molecular Recognition Technology (MRT), a highly selective separation technology using specifically designed ligands (such as macrocycles), has been demonstrated to be an effective treatment process for removal of several ions that are commonly found in many hydrometallurgical circuits as well as in environ-mental treatment operations. Ions removed by MRT include base, heavy and transition metals, precious metals, halides, and alkali/alkaline earths. A MRT pilot plant run was conducted at Zincor to demonstrate the cobalt/nickel purification of zinc electrolyte, and to recover saleable pure cobalt/nickel sulphate solution. The MRT process holds various advantages, which include the elimination of a catalyst such as arsenic trioxide, conventionally used in cobalt and nickel cementation. SuperLig® 138 can be used to remove cobalt and nickel from120?170 g/l Zn-solutions at pH 1?2. The Zincor MRT application demonstrated its capability of concentrating large volumes o copper barren impure solution at low cobalt and nickel concentration levels in the feed, to small solution volumes at high cobalt and nickel concentrations. Around 99.5% of the cobalt was removed from solution with cobalt impurity levels in feed varying between 10 mg/l and 26 mg/l.

Jan 1, 2002

By Patrick J. Foster

This paper summarises a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialled at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By L. Sahu, S. Bhattacharya, S. Dey

"An ideal procedure to determine the limits of flotation-based separation, as is the case with washability analysis for density separation, does not exist. Therefore, a procedure called release analysis, considered to be the counterpart of the washability process in density separation, was developed to evaluate the flotation characteristics of coal fines. Since flotation is a complex process it is necessary to know the maximum recoverable yield that could be achieved at a target ash level and what could be obtained by release analysis. Due to a number of limitations in the initial procedures, modifications were recommended by various researchers to generate an optimum separation curve. This paper presents a review of, and a discussion on, the chronological evolution of release analysis methodology over the decades. Notwithstanding the availability of a standardized release analysis procedure, such as BS 7530, the paper highlights the critical parameters involved in the procedures, such as coal type, feed characteristics, choice of reagents and dosage, operator bias, and design features of the flotation cell IntroductionCoal is a heterogeneous substance consisting of various combustible constituents (macerals) and associated mineral matter. The kind and abundance of the various macerals present in the coal, such as vitrinite, semivitrinite, exinite, and inertinite, determine the type of coal. As macerals are formed by biological degradation of different parts of the plant material, they have different properties based on their original composition. Coal cleaning processes are dependent on the differences in physical properties between the coal components (the macerals) and also between the macerals and the mineral matter. Thus the cleaning characteristics of the coal might vary from one type to the next. The cleaning processes influence the distribution and the concentration of macerals in the various size and density fractions of the cleaned product."

Jun 1, 2019

By P. K. Van Manen

Anglo Platinum's Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex. Approximately 60% of the total concentrate received is from UG2 Reef, and 40% is from Merensky Reef. The concentrate is dried in two flash dryers, and smelted in a single 168 MVA furnace. A PGM-rich nickel-copper matte is cast, crushed and transported to Rustenburg for converting. The plant was commissioned in March 2003. The wet concentrate, containing 12-18% moisture, is weighed, sampled by one of two auger samplers, and off-loaded into a concentrate shed, either directly through a grizzly into a hopper, or onto the floor. From the shed the concentrate is conveyed to 12 concrete silos. Each of the two identical flash dryers can be fed from six silos. From the flash dryers concentrate is transported pneumatically to a 3 000-ton dry concentrate storage silo. The flash dryers are rated at a nominal 66 tph of dry concentrate at 14% moisture, while the furnace can smelt 90 tph of dry concentrate. Therefore both flash dryers are required to operate when the furnace runs at design throughput. Each flash dryer consists of a hot gas generator (HGG), a disintegrator and drying column, and a section for gas/solids separation. In the HGG, gas heated up to 700° C is produced from the combustion of coal peas in a fluidized sand bed. The hot gas and wet concentrate are introduced to the disintegrator at the bottom of the drying column. The disintegrator breaks up any lumps of concentrate, and throws the concentrate up into the drying column, where it travels co-currently with the hot gas. A fan draws the hot gas from the drying column and through the gas/solids separation section, which consists of three primary cyclones, a multiclone and a high-temperature bag house. The dry concentrate reports to a 450-ton dry concentrate storage bin. A portion of dry concentrate is recycled to the wet concentrate feed in a paddle mixer, so that concentrate that is too wet does not enter the disintegrator. The drying column outlet temperature is controlled at 120° C. Coal is received by road, screened for oversize and conveyed to a 400-ton concrete silo. From here it is pneumatically conveyed to a small feed bin at each of the HGG' s. The optimization work consists of process control improvements relating to the HGG outlet temperature, to control the drying column temperature during the ramp-up of the HGG outlet temperature and bag filters. Furthermore a heat balance is used to evaluate options to increase the instantaneous drying capacity of the existing equipment. The coal consumption derived from the heat balance is compared with the actual coal consumption. The purpose of the optimization work is to achieve an operating schedule for the flash dryers such that they operate simultaneously for as short time as possible. Most of the time one flash dryer should operate, allowing maintenance to be done on the other flash dryer, while drawing down the dry concentrate stock. Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals (PGM), base metals, flash drying, fluidized bed.

Jan 1, 2006

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

Council for 2002/2003 President S.J. Ramokgopa President-elect T.R. Stacey Vice-presidents Senior F.M.G. Egerton Junior W.H. van Niekerk Immediate Past-president A.A.B. Douglas Honorary Treasurer J.A. Cruise

Jan 1, 2003

By V. Léveillé

As new legislation drives metallurgical plants to lower SO2 emissions, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost-effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an a mine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 by-product stream, which can then be directed to the front end of a sulphuric acid plant for conversion to sulphuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulphuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature, SO2 emissions in the treated gas can be controlled to as low as 55mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System, as well as which features and cost advantages for the treatment of smelter gases were important in the technology choice.

Jan 1, 2009

By S. Ganguly

Slag samples taken from adjacent to the furnace wall of a submerged arc ferromanganese smelting furnace have been found to contain high concentrations of K2O. To characterize the phase equilibria relevant to these slags experimental studies have been carried out to determine pseudo-ternary sections of the form ?MnO?-CaO-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.65 and 6.0 wt% K2O for temperatures in the range 1523-1673 K. In the pseudo-ternary section investigated the primary phase fields are found to be mullite, 3Al2O3?2SiO2; corundum, Al2O3; spinel, MnO?Al2O3; manganosite solid solution, (Mn,Ca)O; dicalcium silicate,2CaO?SiO2; gehlenite 2CaO?Al2O3?SiO2; anorthite CaO?Al2O3?2SiO2; kalsilite KAlSiO4 and leuciteKAlSi2O6. It was found that the presence of K2O in the slag decreases liquidus temperature in the anorthite and gehlenite primary phase fields. The manganosite primary phase field is expanded in the direction of increased (Al2O3+SiO2) and the liquidus temperatures in the manganosite primary phase field are increased significantly with the presence of K2O in the slag.

Jan 1, 2007

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

Poorly designed sampling protocols generally result in high project risk by artificially increasing grade variability (ie the nugget effect). Sample collection, preparation and assay protocols that suit the ore type, together with QA/QC systems, will reduce this risk. All reporting codes (eg JORC, 2004) require the Competent Person to consider the quality and implication of sampling and assaying programs. High sampling errors beget higher project uncertainty; despite this fact, sampling does not receive the attention it deserves. The case studies presented show that many sampling issues frequently go unrecognised or unaddressed, resulting in poor project decisions during exploration through to feasibility and production. The overall conclusion is that correct sampling is critical to mining project success and that there is often a need for its optimisation.

Jan 1, 2007

Minutes of meeting held at the Moth Hall, Witbank on 13th November, 1969. There were present eleven members: Mr J. Meintjes (in the chair); Messrs I. E. van Aswegen, O. T. Wright, A. W. L. Brereton, A. Bain, J. Brook, P. J. Beukes, C. H. Coxon, B. F. v.d. Merwe, A. C. Hofmeyer, G. E. Carlyon. Six Associate Members: Messrs E. J. Jackson, J. N. H. Pritchard, R. E. Powell, W. Weber, R. Smith, B. T. Hosking. One Student Member Mr M. J. de Beer. Seven visitors. The Chairman reminded members of the intended visit to Barberton. Dr Stander, Director of the National Institute for Water Research, gave an interesting talk, illustrated with slides and a short film, on the conservation and reclamation of water in South Africa. After question time, Mr Hector, Witbank Town Engineer (visitor) thanked Dr Stander. The meeting closed at 7.10 p.m.

The mathematical models of semivariograms can be classified according to whether or not they correspond to situations where the second order stationarity conditions are satisfied (§ 3.3.4). If second order stationarity exists, the a priori variance s2 of x (z) also exists and is finite. For large distances h such that x (z) and x (z + h) are not correlated, the semi- variogram ? (h) will reach a value equal to s2 [this is a consequence of (3.27) above]. This limiting value is called the sill C of the semivariogram, and the distance at which ? (h) reaches the sill is called the range. The range of the semi- variogram obtained from a given type of sample corresponds to the distance of influence of these samples. If only the intrinsic hypothesis is satisfied, the sample variance is an increasing function of the size of the area or volume in which the samples are located, and the semivariogram ? (h) will be a continuously increasing function of h. Remark: It will be shown in Chapter 7 that the variance s2 of x (z) in the ore body O is equal to the average value of ? (h) in O. If ? (h) is a non-decreasing function with sill C, the average value of ? (h) in O will be less than C. s2 and C will be equal only if for some values of h in O, ? (h) exceeds C. In practice, if the range of the semivariogram is small with respect to the dimensions of the ore body, the difference between C and s2 will be negligible.

Jan 1, 1978

By N. Mulaudzi, S. Archer

"Direct cobalt electrowinning was developed to produce unrefined cobalt metal as an alternative to producing a mixed hydroxide product (MHP), which is the common cobalt intermediate product in African Copperbelt operations. MHP is preferred due to the high cost of producing high-grade cobalt cathode. Direct cobalt electrowinning test work results have shown that the purity of the unrefined cobalt metal produced from a low-grade copper solvent-extraction raffinate stream was ~97% (w/w), which is significantly higher than the MHP purity (up to 45% (w/w) Co). The current study investigates whether direct cobalt electrowinning would increase the profitability of African Copperbelt copper–cobalt oxide operations, when compared with the MHP flowsheet. An order-of-magnitude economic evaluation was conducted using dynamic differential discounted cash flow models on a “bare-bones” basis, using a 10% discount rate. Three variables were evaluated, namely; reagent utilisation extents, precipitation extents and filter-press wash efficiency. Multivariable risk analysis was also conducted using the Monte Carlo simulation technique to understand the impact of key project drivers. The financial study results indicated that a direct cobalt electrowinning flowsheet could potentially result in a higher mean net present value (NPV) compared with the MHP flowsheet. Cobalt recovery was found to have the most significant impact on the NPV. In addition to increased profitability of African Copperbelt operations, direct cobalt electrowinning has the potential to reduce the environmental footprint of operations as well as addressing the Democratic Republic of Congo government’s drive towards export of higher value metal products instead of low-grade intermediates."

Jan 1, 2015

By W. E. Stumpf

"SynopsisSouth Africa recently announced a resurgence in its commercial nuclear power programme. The implications for the development of the necessary high-level manpower within South Africa’s tertiary educational system and its national research and development (R&D) capacity in materials science and engineering, as well as in other engineering disciplines, are placed into perspective. An organized national process of developing this manpower by moving away from the previously high-risk and costly ’large programmes’ to rather a selection of ‘small and better’ research projects and a redefinition of what constitutes ‘nuclear materials’ are proposed as parts of this strategy.IntroductionSince 2008, and more particularly in 2014/2015, South Africa has woken up to the fact that significant steps need to be taken to ensure sufficient electricity generating capacity for the future, even beyond the coal-fired stations at Medupi and Kusile currently under construction. It is, therefore, encouraging to see some active large-scale wind farms in the Eastern Cape near Jeffrey’s Bay, in the Couga area, and others in the Western Cape already in operation. In addition, many solar energy projects are also progressing from the small localized scale to larger programmes in the Northern Cape, which may contribute some capacity on a national basis. South Africa needs to tap into its renewable resources of wind and solar much more, but will these projects solve the country’s long-term industrial needs? Unfortunately not. One cannot run mines and trains on solar cells. Industry needs reliable baseload capacity, and with very limited easily accessible hydrocapacity this leaves really only coal, possibly natural gas, and nuclear power as options. South Africa’s current over-reliance of about 90% on coal–fired power, however, places it in an internationally vulnerable position, and diversification into a more equitable energy mix should be a national priority for the medium to long term. South Africa cannot significant climate change confronting the human race, as the IPCC cautioned in 2013, and will have to adjust its future energy reliance to a more balanced combination of sources."

Jan 1, 2015

By J. N. Van der Merwe

The data base of failed coal pillars in South Africa was analysed with regard to the time of failure in an effort to develop a method to predict how long after their formation coal pillars will fail. It was found that meaningful results could only be obtained by splitting the data base up into groups that displayed similar behaviour. It was postulated, based on observation and experience, that coal pillars fail by a process of progressive weakening progressing into the pillar from the edges. Minimum pillar dimensions to ensure failure were calculated?these were the dimensions that corresponded to a minimum ?real? factor of safety. From the scaling distance required to reach the minimum safety factor, rates of scaling for the failed pillars were calculated based on the observed real lives of the pillars. It was found that the rates of scaling were unique for different mining areas and that they correlated directly with mining height and inversely with time. Using the derived scaling rates, the predicted pillar lives were back calculated for the pillars in the data base of failed pillars. In two of the three groups, the predicted lives correlated well with the observed lives on a one-to-one comparison. In all cases, the predicted lives were in the same time range as the observed lives. Overall, the frequency of predicted lives closely replicated the observed frequency of observed lives of the pillars in the data base of failed pillars. The method was successful in distinguishing between the data base of failed and a representative sample of intact pillars. While the predictions matched the observed lives of failed pillars, the predictions of expected lives for intact (hitherto unfailed) pillars were orders of magnitude greater. It is now possible to estimate the frequencies of future pillar failures for the purposes of mine closure and undermining of surface structures within broad bands.

Jan 1, 2003

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, P.D. Box 1183, Johannesburg.

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2(Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ?phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By C. Musingwini

The South African platinum mining industry is using a number of different mining methods, including variations of the same method, to extract the narrow reef tabular platinum deposits of the Bushveld Complex. These mining methods fall into three broad categories, namely conventional, mechanised and hybrid mining. A question sometimes asked in the industry is whether mechanized mining methods are more efficient than conventional mining methods. An objective answer requires the methods to be evaluated against multiple criteria simultaneously, whereby each criterion has a relative degree of importance in the overall decision. The most efficient method is the one that scores highest on each criterion. However, some of the criteria can be conflicting, such as by increasing dilution the shaft head grade decreases. The analytic hierarchy process (AHP) methodology was selected for the study because it is used to solve problems of this nature. A survey was carried out to determine the relative importance of each efficiency criterion by drawing on the knowledge and experience of mine technical services and project management practitioners in the industry. Efficiency data for four different mining methods drawn from the Egerton (2004) study were used as a case study. The conventional mining method ranked as the most efficient mining method from the four methods considered. The exercise indicates potential for the AHP to be used in the South African platinum mining industry as a tool for selecting optimal layout designs, conduct regular evaluation of the performance of production shafts, or objectively evaluate line managers for promotion. The work described in this paper is part of the methodology used in a current PhD research study at the University of the Witwatersrand. Keywords: Analytic hierarchy process (AHP); multiple criteria decision analysis (MCDA); decision-making; conventional mining, hybrid mining, mechanized mining.

Jan 1, 2008

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988