Search Documents

By D. G. Millenbruch

An account is given of a four-phase system for the appraisal of a mineral project while it is still in the exploration stage, and for continual consideration of a favourable appraisal until the production stage is reached. There are ten stages from the idea of a likely project to the production stage, and all the staff that are eventually to be concerned with the development of the project are involved at an early stage.

Jan 1, 1979

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

The following papers were presented at the colloquium* on `Mining methods and economics for improved coal extraction, and coal processing and preparation', which was held in Witbank on 3rd and 4th October, 1979. Review of Mining Methods for Improved Extraction of Coal, by P. King, of Gold Fields of South Africa, for¬merly of the Chamber of Mines of South Africa. The Application of Continuous Miners in South African Coal Mines, by J. D. Inch, Bosjesspruit Colliery, I. Brumby, South Witbank Coal Mine Ltd, J. D. Stone, Matla Coal Ltd, and C. J. Beukes, Usutu Colliers Ltd. Longwall Mining Experience at Coalbrook Collieries, by P. G. Henderson, General Mining and Finance Corporation Limited (with a contribution by C. J. Cloete, Sigma Colliery, Sasol I). Pillar Design in Coal Mines, by Dr H. Wagner, Chamber of Mines Research Laboratories. Open-cast Coal Mining at Kriel Colliery, by I. Buchan, L. F. Baars, and C. S. Northcote, Anglo Power Colliery, Kriel Division (with a contribution by M. F. Pleming, General Mining Coal Division). Richards Bay Coal Terminal, by B. Dunne, Richards Bay Coal Terminal. Coal Preparation in South Africa - a General Review,

Jan 1, 1979

By J. E. Furze

World-wide hikes in the oil price and the prospect of future scar cities of liquid and gaseous fuels have given enhanced status to the South African coal industry. It is thus understandable that the colloquium held at Wit bank on 3rd and 4th October, 1979, and organized jointly by the South African Institute of Mining and Metallurgy and the South African Coal Processing Society should have attracted more than 400 delegates.

Jan 1, 1979

By J. Levin, I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20fLm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over SO per cent, of high-grade pyrite. were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical test work required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed.

Jan 1, 1979

By D. G. Krige

The scope and salient features of a general risk-analysis model for the main types of new mining ventures are covered in brief outline. The following special features and their effects on the investment criteria are discussed: - various criteria for viability, - the maximum shortfall of funds, - correlations between the grades of up to five ore constituents and between the corresponding product prices. differential inflation and escalation rates for costs and prices, - the estimation, if relevant, of a pay limit based either on the major product only, or on the two major products jointly, - the likely recovery grades of all the products to be obtained when the ore-body is mined to any such pay limit. - an option to take account of the effect on the pay limit of any negative taxation on marginal ore, - investment analyses in current and real terms for individual groups of investors subscribing for equity and any loan capital on differential terms.

Jan 1, 1979

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

In August 1978, the National Productivity Institute invited entries for productivity awards, which it intended making as a recognition of firms and individuals who were contributing to the prosperity of South Africa by effecting outstanding improvements in productivity.

Jan 1, 1979

By H. M. Friede

A short survey is given of the Iron Age smelting sites and smelting furnaces that have been found in South Africa. An attempt is made to classify South African smelting furnaces by the inclusion of functional characteristics such as the numbers and positions of tuyeres. An affinity is suggested between the Venda (eastern Transvaal) type of furnace and an East African type. The principles of the smelting process in South African Iron Age furnaces and the characteristics of the smelting products are discussed. Results of metallographic and chemical analyses of 19 iron specimens found at South African sites are given and compared with those from sites in Zimbabwe-Rhodesia, Mocambique, and Nigeria. The carburization and steeling of iron during primitive smelting and forging are discussed.

Jan 1, 1979

By D. D. Howat, J. van der Colf

Slags of the system CaO-MgO-AI2O3-TiO2-SiO2at had been reduced in graphite crucibles for selected time Intervals were fully re-oxidized so that an assessment could be made of the rate and extent to which the titanium oxide had been reduced. The derived kinetic parameters were studied as functions of slag composition and temperature. The extent of reduction after selected Intervals of treatment could be correlated with the physical behaviour of the melt (in terms of viscosity and electrical resistivity).

Jan 1, 1979

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By U. C. Galimidi, J. M. Stewart, A. J. Van Rensburg

The effect of body movement on convective heat transfer from a man performing a block-stepping task was investigated experimentally by direct measurements of convective heat transfer. A series of experiments was conducted in which a nude man was required to stand at rest or to block step at 12 and 24 steps per minute. Wind speed, which was kept constant during each experiment, spanned the range 0,5 to 3,5 m/so Air temperature was kept constant at 43 °C in all the experiments. The results showed conclusively that the convective heat-transfer coefficient depends on the stepping rate. The effect of body motion can be regarded as being equivalent to an increase in the velocity of the free stream. The equivalent increase in air speed was found to be 0,36 and 0,77 m/s for 12 and 24 steps per minute respectively. Data from various sources, including the present study, indicate that wind speed should be increased by about 0,30,0,55, and 0,80 m/s to account for low, moderate, and vigorous body movements respectively. These findings are of direct relevance to the practical assessment of heat stress.

Jan 1, 1979

United Kingdom mineral statistics 1977. Home, D., Squirrell, H. C., and Venkatesan, J. (compilers). London, Her Majesty&apos;s Stationery Office, 1978. 156 pp. £10,25. Copper mining and management. Navin, Thomas R. University of Arizona Press, Box 3398, Tucson, Arizona 85722. ISBN 0-8165-0586-1. 426 pp. Illustrated. Price Metal statistics 1967-1977. 65th edition. 1978. Metallgesellschaft AG, Reuterweg 14, D 6000 Frankfurt am Main, Fed. Rep. of Germany. 382 pp. Illustrated. Coal mine ground control. Peng, Syd S. John Wiley & Sons. ISBN 0-471-04121-1. 450 pp. Illustrated. £19.75 clothbound. Associate Professor and Chairman of the Uranium supply and demand: Proceedings International Symposium, London, July 1978. Spriggs, Michael J. and Casteel, Kyran D. (editors). Mining Journal Gemorfologiesewoordelys/Geomorpho logical vocabulary. Van der Merwe, J. S., en De Villiers, A. B. (samestellers).

Jan 1, 1979

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon&apos;s &apos;face element principle&apos; to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By L. N. Stewart, H. L. Bovey

Since 1955 extensive pressure-leaching testwork has been conducted by Anglo American Research Laboratories (AARL) in laboratory-scale batch autoclaves. In 1958asmall continuous pilot-plantof45 kgofsolids per hourwas operated by AARL. In 1974, when high uranium prices were anticipated, Anglo American, encouraged by successful commercial- scale autoclave operations as practised by Outokumpu, Sherritt Gordon, and Impala Platinum, decided to install a continuous pilot plant at Western Deep Levels. At that time the proposed pilot plant was considered to be of prototype size. The project was funded by members of the Nuclear Fuels Corporation (Nufcor). Since its commissioning in February 1977, the pilot plant at Western Deep Levels, which can treat between 10 and 20 tons of dry solids per hour, has been used to test ores from four different mines. The paper compares the uranium extractions and pyrite oxidation obtained in laboratory batch autoclaves with those obtained in the continuous pilot plant. In general, differences in uranium extraction are not great and can be explained; the differences in pyrite oxidation are less well understood. The effect on plant design of the evolution of carbon dioxide during leaching is discussed. Evaluation of the equipment and materials of construction would have been almost impossible in a small-scale batch autoclave. It is doubtful whether such results would have generated the necessary confidence to permit decisions to install a commercial-size plant. The development and performance of the multistage pumps, instrumentation, shaft seals, and shaft-seal water treatment are discussed. It is concluded that the operation of a largescale continuous pressure-leaching pilot plant to supplement laboratory batch autoclave tests has been a necessary part of the development of this process.

Jan 1, 1979

Discussion of the above paper by G. J. van JAARSVELDt Mr Ortlepp&apos;s paper is important, and deals with a subject towards which much controversy and insufficient basic scientific logic, in my opinion, have been directed. He attempts to remedy some of our unscientific popular misconceptions, and for this we thank him. However, I regret to say that experience has shown that some of his statements cannot be allowed to pass unchallenged. Author&apos;s reply Mr Van Jaarsveld&apos;s contribution is welcome because it provides an opportunity for me to clarify certain points that were perhaps not adequately explained in the paper.

Jan 1, 1979

By S. L. Crouch

A. C. Dieringt The procedure described by Professor Crouch for the modelling of mining in faulted ground allows the elastic and inelastic deformation to occur simultaneously, that is, fault slip occurs while an element is being mined. The energy release rates (ERR) shown in Crouch&apos;s Fig. 10 are apparently calculated from his equation 9 using the i total deformation Din (see the upper load line of Fig. I) Refractories The institute of &apos;Gesteinsh iittenkunde&apos; of the technical university at Aachen, the Refractories Research Institute at Bonn, and the Verein Deutscher Eisenshiittenleute (VDEh) at Diisseldorf are to hold the XXII International Refractory Colloquium on 27th and 28th September, 1979, at Aachen.

Jan 1, 1979

Four engineering products and three consumer products have received awards in the 1978 Shell Design Awards competition organized by the Design Institute of the South African Bureau of Standards. Norman Hanson Visiting Fellowship The Norman Hanson Visiting Fellowship, supported jointly by the National Development Fund for the Building Industry (inaugurated by the Building Industries Federation (8.A.)), the Institute of S.A. Architects, the Association of S.A. Quantity Surveyors, and the National Building Research Institute of the CSIR exists to finance fully or wholly visits by eminent authorities from overseas to South Africa for the purposes of seminars, informed discussions, consultation, and possible active participation in scientific, technological, and development projects of importance to the building industry.

Jan 1, 1979

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By H. Skretting, J. Gundeesen

The paper compares operational parameters for the electric reduction smelting of pig iron and ferroalloys in pilot and industrial furnaces. Data from two pilot furnaces of approximately 200 and 500 kW operating-load capacity, as well as from several production furnaces, are included. Examples are given for the smelting of pig iron, ferronickel, ferromanganese, ferrochromium, and ferrosilicon. In most instances, the results from the pilot furnaces, such as the values for consumption and product analyses, corresponded fairly well with comparable data from the industrial furnaces. For ferrosilicon, the power consumption in the pilot furnace was higher than that in the industrial furnace.

Jan 1, 1979