Search Documents

By Yi Luo, FENGLIANG WU

Mine gob has long been a safety concern in the coal industry due to the air flowing through the gob area. Therefore, knowledge of the airflow distribution and locations of hazard zones in longwall gob is important to prevent and control these hazards. Due to the inaccessibility of mine gob, many numerical studies have been performed to simulate gob air leakage using computational fluid dynamics (CFD) programs, but most of the studies isolated the gob from the mine ventilation network (MVN) with only predefined pressure boundary conditions. The MVN is, in fact, not static in a dynamic longwall mining process, and it consequently changes the boundary conditions and the gob flow field (GFF). Therefore, the MVN should be incorporated in the CFD model to prescribe the transient boundaries. However, it is very challenging to couple the 1D MVN and the 2D/3D GFF to make the mine ventilation simulation realistic. This research uses a proposed novel finite tube method (FTM) to couple the MVN and GFF. In the FTM, the GFF is discretized into a finite number of flow tubes, each of which is formed by two adjacent streamlines. These tubes connect the MVN into a new coupling network. Based on the FTM, a model for gas migration in gob is established for delineating the hazard zones of explosive methane concentration and spontaneous combustion.

By Rafael C. Castro, John Overton, Gregg Sherry, David A. Sutter

This paper presents an innovative ground support solution developed to construct a tunnel cross-passage for the MUNI Metro Turnback (MMT) Project. A “soft center” jet grouting approach was designed to provide solid ground support while maintaining a soft center to allow for hand-mining of a 2.44 m (8 ft.) wide, 3.66 m (12 ft.) tall and 4.6 m (15 ft.) long cross-passage through soft Bay Mud. Prohibitive costs and schedule impacts associated with mining under compressed air (at the time being used for main tunnel construction) were the catalysts to search for alternative methods for cross-passage construction. Limited surface disruption, relatively low costs, ease of subsequent excavation, nominal schedule impacts and proven local success of jet grouting were key factors in selecting and designing this method of ground support.

Jan 1, 1997

By R. C. Gilmore

Computational fluid dynamics (CFD) has been used to model gas compositions in underground longwall coal mine gobs to study oxygen ingress and the development of potentially explosive methane-air mixtures that may form in the gob. The scenarios studied involve various headgate and tailgate ventilation and inertization schemes and controls. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at Colorado School of Mines have used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of bleeder and bleederless mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob. The back return was successful in maintaining sufficient oxygen concentrations in the tailgate corner of the longwall face.

Feb 23, 2014

By Mohammad Hossein Sadaghiani

"Construction of underground structures in urban areas is a very challenging work. There are generally two methods of construction, an open cut-and-cover and underground method. To eliminate the subsurface and surface disturbance and street traffic problems, underground method is preferred. The stress redistribution caused by underground excavation induces movements and deformation in the earth mass and ultimately at the ground surface. This is more pronounced in large space excavations. Generally pre-supporting system is used to control ground deformation and thus enhance its stability. In this paper an innovative pre-supporting system is presented. Concrete Arch Pre-supporting System (CAPS) is introduced in Tehran Metro in 2002. This method has roots in construction method of an Old Iranian small water tunnels, called Quanat. CAPS is an efficient method for stabilizing large span underground spaces constructed in shallow and soft ground. In this technique underground reinforced concrete elements are constructed around the proposed underground space prior to main excavation. This method is used successfully in over 50 large span underground structures in Tehran Metro stations and road tunnel intersections. CAPS has potential to be used to pre-support the large span underground spaces at any weak ground condition in an urban area.1. INTRODUCTION Underground subway stations can be constructed either by open cut-and-cover or underground construction. Due to the presence of subsurface utilities and street traffics in urban areas, underground construction is preferred to eliminate relocation of the subsurface utilities, and other urban disturbance. Underground construction in an urban area is a very challenging effort. The complexity of the work is more pronounced in a weak and shallow ground. The stress redistribution caused by underground excavation induces deformations in the earth mass and ultimately at the ground surface causing damage to adjacent structures. The need to control ground surface settlements in urban area is widely recognized and new construction methods are continuously developed. Settlements induced by underground excavation may cause serious damages to nearby structures and subsurface underground utilities, (Sekimoto et. al. 2001). In order to improve stability of underground excavation and reduce settlements, various ground treatment techniques are presented, Johnson, et.al., (1983), Carrieri, et.al. (2002), and Ocak (2008)."

Jan 1, 2016

By D. Tao

More than 80 million metric tons of fly ash is produced annually in the U.S. as coal combustion by-product. Fly ash can be converted to value-added products if unburned carbon is reduced to less than 2.5%. However, most of fly ash is currently landfilled as waste due to lack of efficient purification technologies to separate unburned carbon from fly ash. A rotary triboelectrostatic separator has been developed and patented recently at the University of Kentucky with unique features. Several fly ash samples have been used to understand the effects of major process parameters on the separation performance. The results show that compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator has significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range. Key words: Coal, Combustion Waste; Fly Ash; Particle charging; Separation.

Jan 1, 2008

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By Amin Mousavi, Soroush Khazaei, Yashar Pourrhimian

As a factory-like method, sublevel caving consists of development activities, stockpiling and production activities that are carried out on different levels independently. Therefore, considering the operation from the development phase to the plant will lead to more reliable production scheduling. This paper presents a mixed integer linear programming framework for the long-term production scheduling of sublevel caving that maximizes the net present value while satisfying development activities, mining, and processing capacities, continuous mining, the allowable number of active mining units, grade blending, and vertical and horizontal sequencing. The model is coded in Jupyter Notebook and is solved using the CPLEX solver.

Jun 25, 2023

By Y. Luo

Based on the concept of slope stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain has been proposed. The slope geometry and soil physical and mechanical properties of the surface natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach in studying ground movement in hilly regions.

Jan 1, 1998

By Michael J. Rinker, P. A. Tibble, M. Wiseman, R. V. Nicholson

Tailings, from an active copper-zinc operation, containing about 10% sulphur were investigated to assess the onset of acid production and potential lime requirements for treatment of drainage. Oxygen consumption rates were measured over two years to verify spatial and seasonal variations in sulphide oxidation rates. Shallow cores were collected to assess the quality of tailings porewater and to characterize solids that had been subjected to oxidation and depletion of neutralization potential (NP) for several years. Oxygen consumption data were used to quantify rates of NP depletion and onset of acid drainage from the near- surface tailings. Based on measured oxygen consumption rates and identification of NP remaining in the tailings, future lime use in the treatment plant was expected to rise significantly without mitigation. Geochemical modeling calculations were calibrated with observed oxygen consumption rates and the model results agreed well with actual lime use in the waste water treatment plant during operations. The modeling also demonstrated the benefits of lower lime demands and treatment costs after closure as a result of construction a soil cover on the acid generating tailings.

Jan 1, 2000

By Darrell M. Hladun, Linda M. Dufour

The benefits of computer simulation in the design of a refracto­ry gold autoclave facility is discussed. Three computer simula­tion programs used for autoclave design are briefly described in this paper. 1) METS IM® - A Process Simulation Software Package Developed by Proware: Mass and energy balances are conducted around the auto­clave and its ancillary processes. Results from the process simulation define process equipment requirements and are used for establishing operating costs. The p_rocess model integrates various unit operations including grinding, acidu­lation, pressure oxidation, counter-current-decantation, neutralization, cyanide leaching, and carbon-in-pulp or car­bon-in-leach. 2) ALGOR® - Finite Element Analysis (FEA): A computer software program is used in the design and analysis of brick lined pressure vessels, such as autoclave, heater, and flash vessels. This software creates a steady state thermal model, and accurately predicts temperature distribution throughout the entire vessel, including nozzles, which represent regions of high thermal intensity. 3) Compress©: A software package developed by Codeware used for the sizing of pressure vessel components, includ­ing shells, heads and nozzles, according to ASME Boiler and Pressure Vessel Code, Section VIII, Division 1.

Jan 1, 1996

By K. Hartman

Certain external forces affect the manner in which business is conducted. and in recent years changes in the business environment have altered how some of these external forces affect the management of a business. These changes must be understood and considered in definition of the strategy of the business. Implementation of the strategy must assure commitment from all departments within a company, and this commitment sometimes involves compromises to assure that a department's goals mesh with the overall business objective such compromises must be externally motivated. i.e. for benefit of the customer. Complete implementation transcends internal departments to all aspects of managing the efforts in the marketplace.

Jan 1, 1989

By R. L. Grayson

An integrated approach to mine management is presented. A model for achieving the level of control of operations critical to surviving in the current market is outlined. The integrated Production and Cost Management System (PRaCaST) is designed to provide mine managers with a reliable, quantitative, decision-assisting system that can be used in formulating timely responses to complex fluctuations in operations. PRacaST consists of a productivity forecast model, sectional bills of materials containing current resources consumption factors, a linear programming scheduling model, and operations analyses that focus on production and cost performances. The system is applied to an underground coal mine.

Jan 1, 1988

By Leslie Thompson, Randy Hiebert, Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology is capable of detoxifying cyanide and nitrate and immobilizing metals in wastewater from agitation cyanide leaching as well as heap leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to detoxify cyanide and immobilize several metals from a mine process wastestream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-01-0. MSE Technology Applications, Inc. (MSE) located in Butte, Montana, was the contractor responsible for conducting the project, and Pintail Systems Inc. of Aurora, Colorado, was the technology provider. The pilot-scale unit was field tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was con­sidered to be very successful in detoxifying cyanide from the mine process water. The process was also determined to be very effective in removing metals. The pH was consistently neutral­ized and nitrates were successfully removed in the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to offer an innovative, cost­effective alternative for the treatment of mining wastewaters.

Jan 1, 1998

By R. Hiebert, M. Foote, S. Nordwick, M. Canty

An innovative biological treatment system designed to detoxify cyanide and nitrate and immobilize metals from cyanide leach operations is described. A pilot-plant demonstration was conducted to detoxify cyanide and immobilize several metals from a process stream at the McCoy/Cove Mine. Testing was performed under the EPA’s Mine Waste Technology and Superfund Innovative Technology Evaluation Demonstration Programs. This technology was successful in detoxifying cyanide and effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed. Results show that biological treatment can offer an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1999

By M. Canty

An innovative biological treatment system designed to detoxify cyanide and nitrate and immobilize metals from cyanide leach operations is described. A pilot-plant demonstration was conducted to detoxify cyanide and immobilize several metals from a process stream at the McCoy/Cove Mine. Testing was performed under the EPA's Mine Waste Technology and Superfund Innovative Technology Evaluation Demonstration Programs. This technology was successful in detoxifying cyanide and effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed. Results show that biological treatment can offer an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1999

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

A thorough improvement in mine safety is contingent on many factors that require scientific decision-making for selection and prioritizing of important factors for safety improvement. Their analysis using an established scientific method can improve mines’ safety conditions and assist the administration for informed decision-making. This research establishes a mine safety evaluation index and proposes an integrative model based on the entropy weight and grey clustering methods. In the evaluation index, 27 significant factors of safety are identified and categorized into 7 criteria. The proposed evaluation system analyzes all indicators according to Pakistan’s current mine safety situation and their significance for potential safety improvement in the future. Results reveal that current safety practices are outdated due to a lack of mechanization in the mining industry and minimal capability of the management to achieve the desired safety targets. Appropriate safety policies and safety education are missing in the daily working environment. The lack of overseeing the execution of safety operations and the lack of ambition and strong work ethic workers contribute to the paucity of mines’ safety conditions. The prevention and control systems to manage risks and hazard are not in place, and the working environment in mines remain difficult. Therefore, to have enhanced mine safety, important factors can be addressed in chronological order, as presented in this paper. The proposed methodological approach can be applied to other prioritization applications to analyze the indicators and determine the appropriate management strategies.

Jun 14, 2021

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

The analysis of mine safety indicators using a scientific method can improve mine safety and assist management in making informed decisions. This research establishes a mine safety evaluation index and proposes an integrative evaluation model based on the entropy weight and grey clustering methods. The index consists of 27 indicators classified into seven criteria: working environment (A), miners’ attributes (B), safety policies and education (E), prevention and control (F), and monitoring and supervision system (G). Using Pakistan’s mine safety situation as a case study, the proposed model categorized the indicators into five safety levels (very low, low, medium, high, very high) for the present situation and for their relevance in terms of future safety improvement. The results show all of the criteria falling into the very low level for the current mine safety situation. Three of the criteria — C, E and G — are identified as having very high levels of significance for future safety improvements.

By Akira Usui

Ferromanganese crusts on topographic highs in the western Pacific Ocean are believed to be potential resources of cobalt, nickel and platinum. Earlier shipboard geological and geophysical studies by Japanese organizations have focused on mapping of distribution of thickness and metal contents of the deposits when estimating the total reserves. This paper summarizes our attempt to obtain more feasible data of distribution patterns and configuration of the deposits which are important parameters for resource evaluation at some seamounts in the South Pacific Ocean. Morphology of the seamounts and micro-topography of the sea floors are described using shipboard acoustic remote sensing, deep-tow sonar images, and TV/camera. [ ]

Jan 1, 2008