Search Documents

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By T. Kretschmer, F. Villwock

Conveyor systems are an essential part of many material movements in all conceivable areas of application. They are used to transport goods in raw materials extraction, agriculture, and even articles for daily use. In the process, not only distances of several kilometers but also differences in altitude of several hundred meters are bridged. The layout of the conveyor usually follows the topography at the respective installation site. Particularly in the case of large height differences, safety devices must be provided to prevent uncontrolled movement. Backstops can take over this task in predominantly ascending overland conveyors and are used either as a primary or as a secondary safety system in conjunction with a service brake. They are always used when the system comes to an unplanned standstill, whether due to a power failure, an emergency stop or a defect. When designing backstops, it must be ensured in any case that all conceivable circumstances are taken into account so that failure is ruled out without the product being unnecessarily large in size. Various safety factors are applied, some of which are even prescribed by authorities. One example is the Australian standard on machine safety for bulk material belt conveyors (AS/NZS 4024). This stipulates a redundant acceleration safety device that can absorb at least 150% of the maximum load. ALTRA Industrial Motion with its sister companies Marland and Stieber manufacture backstops for a wide range of applications. With more than 85 years of business activity in freewheeling and backstop applications, they are among the most known and experienced companies and provide a great know-how.

Mar 2, 2022

By E. Steiakakis

This paper presents in detail the procedures followed and the results obtained in order to determine the stiffness parameters of the calcareous marls found in the lignite mines in Ptolemais, Northern Greece. Triaxial tests were performed on representative samples of the inner burden marl and the marl which underlies the lignite bearing series of the region. The tests were conducted under drained conditions, with controlled loading (including an unloading-reloading loop), while the axial strain was measured externally as well as with displacement transducers mounted directly on the specimen (Hall Effect sensors). The geotechnical parameters obtained (i.e., cohesion, angle of friction, stiffness modulus, stress-strain relationship), were subsequently used for simulating the triaxial testing with the Plaxis finite element software. Simulation results are in good agreement with the experimental results. The resulting material model can then be applied to modeling the mobility that is expressed during the excavation of the open pit mines.

Jan 1, 2005

By Gregg J. Hodges

The Stillwater Mining Co. is a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corp. The Stillwater Mine, located near Nye, MT, is the Western Hemisphere’s only primary platinum-palladium deposit. The mine began production of flotation concentrates in March 1987. In the fall of 1987, an integrated pilot plant testing campaign of electric furnace smelting and oxygen-blown converting confirmed the feasibility of further upgrading to semi-refined matte, or “white metal.” In the summer of 1990, the production smelter was brought on line. The record of the discovery and development of the Stillwater deposit, mine and concentrator has been summarized in several articles (White, 1987; Kennedy, 1987; and Hodges and Clifford, 1988). Similarly, the pilot campaign to test the feasibility of treating the flotation concentrates in an integrated smelting plant has been described (Hodges and Clifford, 1988; Matousek, et al., 1989; and Matousek and Whellock, 1990).

Jan 1, 1991

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By Gregg J. Hodges

The Stillwater pt-pd mine and flotation mill are located about 130 km (80 miles) southwest of Billings in Stillwater county, M6ntana~ The pt-pd ore zone stretches about 43 km (27 miles), but varies in thickness from 0 to 6 meters (0 to 20 feet, but generally 3-6 feet) and dips 55-90,degrees from horizontal. The ore is hosted in basic, layered igneous rocks containing about 1% sulfide minerals which include chalcopyrite, pentlandite, pyrrhotite, and minor pyrite. The pt-Pd minerals are intimately associated with these sulfide minerals and are found as precious metal sulfides, tellurides, bismuthnides, and arsenides as well as native Pt metal. Approximately 90 different precious metal minerals have been found, but about 80% of the pd is in solid solution in the pentlandite. The ore assays about 0.1% Cu, 0.1% Ni, 6.2 g Pt/tonne (0.18 Troy ounce Pt/short ton (opt)), 21.3 g Pd/tonne (0.62 opt Pd), 0.21 g Au/tonne (0.006 opt Au), and 0.21 g Rh/tonne (0.006 opt Rh). The ratio of pd to Pt in the Stillwater ore and concentrates is about 3.5.

Jan 1, 1988

By Harold G. Arthur

INTRODUCTION Stillwater Tunnel construction is scheduled to start in the spring of 1973. The tunnel will be the site of an extensive program in rapid excavation research. This paper presents a progress report regarding our plans and relates the tentative decisions which have been made on how to carry out the research effort. The details are subject to revision as more input is obtained from other Government agencies interested in tunnel construction and from experts in industry and educational institutions. The objective of the research program is to bring about faster, less costly tunnel construction. This objective will be pursued through the development, improvement, and evaluation of various construction systems and investigative techniques. The need for this kind of program was recognized by the National Research Council, in its authoritative report "Rapid Excavation - Significance, Needs, Opportunities." (1) The Council advocated a federally funded $200 million, 10-year program to help meet the $69 billion market it expects in underground excavation between 1970 and 1990. The significance of tunnel construction to Reclamation is made clear by statistics of its tunneling experience and outlook. Reclamation has constructed 174 water conveyance tunnels totaling over 190 miles, Six tunnels are presently under construction which have a combined length of about 27 miles. There are on the books nine authorized, but unfunded tunnel projects totaling another 70 miles in length. Many more miles of tunnels are included in programs in various stages of investigation.

Jan 1, 1997

Stillwater Mining Company (SMC) has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The most recent TBM used is for the Blitz Project, where a 5.5m (18ft) diameter main beam unit, commissioned in Q3 2012, is being utilized to drive a 6,975m (22,500 ft) ventilation and haulage level East of the Stillwater Mine for the Blitz expansion project. The assembly/commissioning of the TBM, institution of the planned diamond drilling program, application of ground control systems, and the current tunneling metrics will be covered.

Feb 23, 2014

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By J. Partyka

Fumes produced during blasting operations in underground mines are defined in this paper by an equivalent contaminant source. The primary goal is to establish a method which would allow all those parameters not measured directly to be determined reliably from field data. The parameters to be identified are the diffusion coefficient , and the position and size of an equivalent source. The diffusion-value is computed from the peak concentrations taken by two monitors located in the drift. The first monitor is placed close to where blasting pollutants join the main stream, while a second monitors is moved downstream a some distance from the first point. The position and size of the dust source and the total amount of dust produced during blasting are determined from the data recorded by only one monitor.

Jan 1, 1991

By K. Kim

A site characterization strategy formulated for the probabilistic design of underground structures is presented, which takes into account the variability of rock properties and the stochastic nature of the rock failure process. It entails determining probability distributions of rock properties by utilizing the theory of extremes and Monte Carlo simulation. Laboratory and field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass properties can be estimated using empirical relationships currently available. This results of analyses can be incorporated into the design of underground structures, and then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1995

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By Tuncel M. Yegulalp

This article summarizes some of the results of the continuing research activity at the Henry Krumb School of Mines, Columbia University, directed towards a better understanding of the stochastic behavior of slurry flows in underground coal-slurry pipeline systems. The slurry system under consideration here replaces all conventional haulage systems between the coal face and the coal preparation plant on the surface. At the beginning of the pipeline system, flow rate and frequency of coal slurry is very closely related to the activities of production equipment at the coal face. Due to several scheduled and unscheduled interruptions in continuous miner's coal mining activity, resulting slurry flows possess stochastic characteristics. Proper understanding of these characteristics is believed to lead to a more realissic and economic design of slurry handling equipment. Fundamental ideas supported by field observations are presented and a Semi-Markov model of the slurry flows is developed. As a result of this formulation, behavior of combined slurry flows from N independent coal faces can be expressed in analytical form. The contents of a slurry surge tank receiving slurry flows with certain stochastic characteristics is investigated as a function of discharge pump characteristics and time.

Jan 1, 1981

By Juan J. Monsalve, Mario Karfakis, AMAN SONI, Nino Ripepi, Jim Hazzard

Pillar collapses are events that due to their severe consequences can be classified as high risk. The design of pillars in underground room-and-pillar operations should migrate to risk-based design approaches. The authors of this work proposed a risk-based pillar design methodology that integrates stochastic discrete element modeling for pillar strength estimation, and stochastic finite volume modeling (FVM) for stress estimation. This paper focuses on the stochastic FVM component for stress estimation. The mining and geomechanical aspects of a case study mine (CSM) are described and pillar stresses are estimated by using three approaches: (1) analytical solutions, (2) 2D finite element modeling, and (3) 3D finite volume modeling. This operation extracts a 30° dipping deposit, which makes current underground stone mine design guidelines inapplicable for this CSM. This work compares results from each stress estimation approach and discusses uses the point estimate method as a simplified stochastic approach to evaluate the effect of rock mass elastic properties variability on pillar stress distribution. Results from this work show that the three estimation approaches lead to different estimations, possibly, due to the wide range of assumptions each estimation approach considers. It was also determined that the horizontal to vertical stress ratio has a significant impact on pillar stress magnitude. Therefore, it is recommended to perform in situ stress measurements, or assume worst-case-scenario values to account and reduce uncertainty due to this parameter. The stochastic stress estimation approach used in this paper provides results that can integrate a risk-based pillar design framework.

Sep 24, 2022

By Nasser Madani, SULTAN ABULKHAIR

The geological and geostatistical modeling of mineral deposits requires densely sampled drillholes that provide accurate and reliable hard data. Furthermore, quantifying orebody uncertainty through geostatistical simulation can allow mining engineers to assess long-term risk in mine planning. Nevertheless, ore deposits can sometimes lack dense drillhole information, reliable hard data with proper quality assurance/quality control (QA/QC), or sometimes both. This study is based on a coal mine located in the Republic of Kazakhstan, where an iron dataset is based on data from three newly drilled drillholes, and geological information comes from a massive collection of legacy drillhole data with no evidence of proper QA/QC. For this reason, a workflow was introduced to construct a representative training image from legacy data and stochastically model geological domains within these three drillholes using a multiple-point geostatistics technique. Once the geological model was obtained, a two-point geostatistics algorithm was applied to model the iron inside each geological domain. The direct sampling algorithm was chosen for modeling geological domains, and sequential Gaussian simulation for iron grade calculation. Both methods were extensively evaluated using different statistical tools and analyses.

Aug 1, 2022

By Nasser Madani, SULTAN ABULKHAIR

The abstract of the paper discusses the challenge of quantifying iron content in a coal deposit in Kazakhstan. The iron dataset is limited, coming from only three drill holes and some stope samples, while a large amount of geological information is available from legacy drill hole data. The paper proposes a workflow using multiple-point geostatistics to model geological domains and two-point geostatistics to model iron content within these domains. The results show that the direct sampling (DeeSse) algorithm effectively reproduces the complex seam layers, and sequential Gaussian simulation models the iron within each domain.

Mar 30, 2022

By R. W. Chappell, M. W. Hills, R. L. Olsen

A stochastic approach was developed and applied to the Butte, Montana Hillside abandoned mining site for modeling stormwater runoff and subsequent receiving stream loadings. This approach enabled capture and quantification of the uncertainty associated with stormwater quality data and allowed the prediction of copper and zinc concentrations in the receiving stream caused by runoff from the Butte Hillside during storm events. Runoff flows and stormwater concentrations were input to the model as probability distribution functions. Monte Carlo simulation allowed prediction of expected instream concentrations in the form of cumulative distributions functions. The modeling results allowed evaluation of current best management practices (BMPs), targeting of future BMPs, and identification of key data gaps to fill during future sampling activities. This modeling approach is considered extendable to other active and inactive mining sites. Output from a model of this type is easily understood and can be used to communicate effective stormwater management to site regulators. Furthermore, application of this modeling approach will facilitate the development and implementation of a site-specific stormwater management plan and will optimize efforts to achieve standards for compliance with stormwater discharge permits.

Jan 1, 2002

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005