Search Documents

By Robert Stefanko

Longwall mining appears very attractive from an engineering standpoint because of its simplicity. The use of one long, continuous face can simplify power distribution, ventilation, and supervision, and minimizes or prevents lost time associated with the tramming of equipment in room-and-pillar systems. Since the longwall system is more amenable to automation, it is inherently safer than room and pillar. Remote control of all face equipment from gate roads will obviate the exposure of men in the face area. Considering what has been said, it seems a paradox that more longwall installations are not found in the United States. However, with favorable mining conditions in relatively level seams of adequate height under shallow cover, it has been possible to develop highly productive, mechanized, room-and-pillar systems. Thus there has been no real incentive to employ longwall in the United States. In Europe, mining companies usually have very little choice between the two systems. Pitching seams of low height located at great depth dictate the use of longwall methods. With depletion of its readily accessible reserves, mining conditions will be similar to those now prevailing in Europe, and an increase in the use of longwall in the United States can be anticipated.

Jan 1, 1963

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

Horizontal stress is an important factor that contributes to roof failure during a long wall entry development, especially when the immediate roof is weak. In this study, the effects of the three factors, the stress angle between the maximum horizontal stress and entry development, the stress ratio of the maximum to the minimum horizontal stresses, and the sequence of entry development, on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method, when the horizontal stress is fixed. The results have confirmed that the stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the angle is about 60°_75°. The stress ratio has little effect on the roof stresses. In addition, the sequence of entry development has also little effect on the roof stress for the specific case analyzed.

Jan 1, 1999

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The overburden responses in gently inclined orebody mining are different from those in horizontal orebody affected by the orebody dip angle. In particular, the mining-induced stress presents asymmetrical distribution characteristics spatially, resulting in stress concentration and large-scale pressure relief phenomenon in the surrounding rock. As a result, frequent ground pressure disasters such as roof collapse and barrier splitting occur frequently. Moreover, the ground pressure evolution law and the interaction between stopes in multistope mining are complex. The effective ground pressure control measures cannot be taken due to unclear understanding of the evolution of stress and displacement fields, justifying the investigation of the distribution and evolution of underground pressure for safe and efficient mining.

Jun 1, 2023

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By M. Cai

Transformation of the measured borehole deformations induced by stress relief relies on the traditional assumption that the rock is continuous and homogeneous. Systematic and quantitative tests were carried out to check the performance of devices commonly used for measuring borehole deformations within different types of discontinuous rock conditions. Test results provide a reliable basis for considering the influence of discontinuities on in situ stress measurement and for choosing the best measuring device for a given rock type and condition.

Jan 1, 1998

By C. F. Lee, Bezalel C. Haimson

A 300 m deep test hole at Ontario Hydro's Darlington nuclear plant site, 65 km east of Toronto, was used to determine the state of stress in the Paleozoic limestones (O-22O m depth) and the Precambrian granitic gneiss (220-300 m). The results of the hydrofracturing measurements indicated a state of high horizontal stress along the depth of boring and a consistent orientation of principal stresses in each geologic unit. These results were confirmed by a borehole TV camera survey, and by overcoring tests. The magnitudes and orientations of the measured in situ stresses were used in a feasibility study of siting an underground nuclear plant, and in particular in the geotechnical design of proposed reactor caverns in Precambrian rocks. Their implications on cavern stability under operational and accident conditions were analytically studied, taking into consideration the potential superposition of thermomechanical stresses under loss-of-coolant condition, and the possibility of thermal spalling in the host rock.

Jan 1, 1979

By Douglas E. Hansen

A current trend in blasting of large volumes of rock is to use increasingly larger diameter shot holes. The use of large diameter holes meant; correspondingly large explosive charges will be loaded and detonated, and, if special efforts are not made, will result in more damage and vibration beyond the intended blast area. With the rising awareness of environmental factors, vibration control becomes increasingly important. Equally important is the preservation of intended lines and grades, and in some cases by blasting with care, slopes can be safely steepended. In the past, vibration control was established to prevent damage to man-made structures. The quarry or open pit itself can be regarded as a structure composed of rock. Far too little attention has been given to the effects of blasting on rock walls. The primary purpose of blasting is to break rock. If the integrity of the rock has been destroyed beyond intended lines and grades, the excavation will be more costly than originally anticipated. The increased cost will not only be from in¬creased excavation due to overbreak, but also increased maintenance due to blast induced wall instabilities

Jan 1, 1976

By Rudrajit Mitra, Wesley B. Johnson, Erik C. Westman

The ability to understand stress redistribution within a mine allows greater extraction efficiency with reduced safety concerns. Stress redistribution has been examined at the laboratory scale using ultrasonic tomography and numerical modeling using PFC3D. A data acquisition system was built to obtain tomograms as samples are loaded in uniaxial compression. Limestone samples were loaded to failure. Three-dimensional tomograms of the samples correlate to various stress distributions. The tomograms are compared to analytical and PFC3D results.

Jan 1, 2005

By ERIK C. WESTMAN, JESSICA M. WEMPEN, DALLAN J. COONS, WILLIAM G. PARISEAU, MICHAEL K. MCCARTER

Safe, efficient underground mining is dependent upon proper pillar sizing. Pillar sizing is typically based on a combination of observation of prior behavior, point measurements, theory and numerical modeling. The actual stress redistribution within a pillar, while assumed for many years, has rarely been imaged. Such imaging can help confirm whether or not theoretical and numerical modeling methods agree with actual conditions within a pillar. This research presents a case study from a longwall mine in the western United States. A two-entry, gate-road yield pillar in the headgate of the mine was instrumented with seismometers and convergence monitoring stations, and was monitored over a period of about six months as the longwall face approached the pillar. In this paper, the stress distribution imaged using seismic tomography is compared to the stress distribution expected from theoretical models, geotechnical measurements and numerical models. The tomography results generally agree with those proposed by theory, convergence measurements and numerical modeling results. The agreement of the methods provides validation for the theorized stress redistribution, and this study provides further evidence that tomography can indicate the redistribution of induced stress within a mined rockmass and is another tool available to ensure that mining is conducted safely and efficiently.

Aug 1, 2022

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By K. Y. Haramy

Deep coal mines with strong roof and floor rock frequently encounter face and rib bursts. The burst problem is becoming more severe as mining depth increases, prompting efforts to relieve high stress areas ahead of mining. Successful stress relief reduces the occurrence of uncontrolled coal bursts. This report by the Bureau of Mines, U.S. Department of the Interior, presents a review of the most widely used methods to detect and destress high stress zones along coal faces. Stress-related burst problems and destressing efforts at a cooperating mine were investigated. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three- dimensional, multiple-seam computer modeling program, "MULSIM?, was used to evaluate the effectiveness of stress relief methods. Modeling results and guidelines for destressing are presented. Results indicate that dangerously high stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1987

By H. Maleki

The U.S. Bureau of Mines pioneered the use of borehole deformation gauges and overcoring techniques to measure in situ stress. These measurements provide input to structural mine design and support selection for specific geologic conditions. This paper presents recent stress measurements in a western U.S. coal mine where the orientation of the stress field remained relatively unchanged over distances of several kilometers. The horizontal stress magnitude increased with depth of cover and in relation to major geologic structures. Local variations in roof stress profiles were used to develop generic models relating stress arching to strata stiffness and the inelastic behavior of mine roof.

Jan 1, 1994

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By J. C. Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult because a slope will transverse through many different types of strata. Over the past three years, Keystone Mining Services, LLC, an affiliate company of Jennmar Corporation, has developed a new methodology designated the ?Stress, Geologic, and Support Design System (SGSsm)?. This patent pending method analyzes the stress, geology, and support design for a mine slope. It has been successfully applied in various new slopes across the United States. This paper will detail the main concepts of the methodology including: (1) Analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) Primary and supplemental support design; (3) Long term support design in the form of steel square sets or arches, and (4) Validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By B. H. Gardner, S. Serata, D. Dickie

Since 1958, the Sifto Salt Division of Domtar, Inc., has operated the Goderich (Ontario) salt mine in Michigan basin bedded halite, with shafts located on Lake Huron's eastern bank. Initial mining utilized a conventional room and pi1lar pattern. However, roof deterioration developed. Incidence of progressive upward failure of saltback and over1yings ha1ey-do1omite layers intensified with entry aging. Studies were therefore initiated on new mining patterns utilizing the Serata Stress Control Method. Pursuant thereto, three test areas, indicated in the mine plan of Fig. 1, were designed and excavated. Full conversion to Stress Control mining was effected in January, 1983. This paper focusses on the instrumentation work in the third test area. Test Area 3 was designed to validate the excavation geometry of the new stress-controlled main entry system. The testing of that design was accomplished, in part, by comprehensive in situ stress, property, and deformation measurements on the performance of the model main entry section of Test Area 3. The paper describes: (1) the theoretical background of the SPDR/Stress Control Method; (2) specific problems and objectives addressed by the 1983 program of in situ measurements, (3) measurement results; and (4) conclusions drawn therefrom.

Jan 1, 1986

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

By Feng Cai

"As a new method to support gate roadways, rock bolting has been widely used in the big coal enterprises for its superiority. The disturbed stress field of surrounding rock and anchor pre-stress field were divided into 3 areas in consideration of s1, s3. The surrounding rock failure form and characteristic were analyzed in combination with parameter f, the failure mechanism was explained using the slip line theory, furthermore, the rock bolting mechanism and its arrangement were studied. After roadway excavation, the tensile stress area appeared at the surface of the surrounding rock. The failure type changes from shallow tension-shear form into deep compression-shear form and the failure shape is an “incense burner”, surrounding by high risk failure area in butterfly shape. The maximum principle stress in roof appears discontinuous distribution because of layers separation. The failure type of surrounding rock is intensity-stress environment-weak plane control model. The internal reason of roadway macroscopic failure is the displacement between the surface plastic area and the deep elastic region along the tangential direction of slip line. In condition of rock bolt support, there is one-way tensile stress area in small range at the surface of surrounding rock, inside is the bidirectional compressive zone in uniform distribution form, stress environment is improved by the superposition of anchor pre-stress and disturbed stress field, anchor rock bolt arrangement and pre-tightening force distribution is decided according to the distribution of f parameter. Finally, supporting method and parameter reasonability was proved by the roadway deformation monitoring, damage depth drilling peep test in the 8101 transportation roadway in a mine.Introduction The stability of roadway support is very important to the safety and sustainable development of coal mine. In recent years, the focus of China's coal mining industry began to move to West China, the thick-extra thick coal seam is developed in the West. The latest technology and equipment have been put in to service, the occurrence condition of thick coal seam and the increasing of productivity lead to the cross section of the roadway increasing continually, hence, it is more difficult to control the surrounding rock. At present, the most common way to support the roadway is rock bolt (cable) support (Wang 2007); Scholars have been deeply studied on the mechanism of rock bolt. It is reported (Wang et al 2012, Gao 2007, Zhang and Yuan 2006) that the influence of rock bolt on physical and mechanical parameters of coal and rock mass in the anchorage zone, It is believed that the rock bolt can improve the peak strength of surrounding rock, especially the post peak strength, and the failure mode of rock mass under the rock bolt support is analyzed. It is reported (Wang et al 2014, Xiao et al 2013, Li et al 2007, Yan et al 2012), according to different geological conditions, the failure mechanism of surrounding rock and supporting technology of the whole coal roadway were studied. Focus on the failure mechanism of roadway surrounding rock, different forms of high strength support methods were proposed, which achieved good results. It is reported (Wang et al 2012a, Zhang et al 2011, Wang et al 2012b, Kang et al 2010, Zhang et al 2010, Kang et al 2007) that the supporting mechanism of pre-stressed anchor was analyzed from the point of the distribution of the maximum principal stress in the pre-stressed anchor field, and the influence of the rock bolt support parameters and surrounding rock characteristics on the supporting effects were studied. Based on the latest research results, this paper analyzed the failure mechanism of surrounding rock of coal roadway, proposed the high strength anchor net cable combined supporting technology based on the feature of stress zoning distribution of surrounding rock, to provide reference for the coal roadway rock bolt (cable) support technology."

Jan 1, 2017

By John Bailey

Stressmap is a program whereby the earth's stress field is charted in detail and utilized for design of mines and mine exploitation. This program is implemented by mapping the attitude (location, direction, dip, and extent) of induced rock ruptures during the process of hydrafracturing drill holes contiguous to mine interest. The program includes utilization of ancillary naturally occurring stress relief signals, They are precipitated because the earth is indeed dynamic and the strata of the crust are continually adjusting to load and/or strain differentials resulting in rock deformation and fracturing. These fracturing adjustments occur as small to tiny earthquakes comparable to Richter magnitudes of one, zero, minus one, and smaller events termed microearthquakes. Obviously, the earth's stress field changes due to continued differential loading and crustal movements; therefore it becomes conspicuously evident that resolving today's stress field as opposed to paleostresses is most important for efficient, economical, and safe mining operations.

Jan 1, 1974