Search Documents

By Qingxia Liu, Chen Tingzhong, Chen Jin, Yang Xiaosheng

It is common problem (Huan Xinsheng, etc.,l992)for most iron ore concentrators in China that the concentration of thickened tailings is lower than the need for economical transportation. To solve the problem, two methods of improving the properties of the existing thickeners and using separate thickening technique have been applied in three iron ore concentrators. However, in the case of the Daye iron concentrator a new technique of cyclone-flocculated sedimentation was developed by present authors and verified by experiments. The new technique employs efficient hydrocydone designed by authors in conjunction with a low cost flocculant named KLP.

Jan 1, 1995

By Gregory E. Tieman

Hydrologic impacts of longwall mining were studied in 1986 after mining had occurred at mine "Z" in northern West Virginia. This mine is 700 to 1,300 ft deep, with a surface topographic relief of 300 to 500 ft. Five springs and one dug well were reportedly dewatered by mining. All such supplies are above nearby streams in elevation, and at least 800 ft above the subsided mine. Three of these six supplies showed partial recovery within one year. Only supplies within 50 ft in elevation of a nearby stream showed apparent partial recovery. Measured perennial streams showed notable depletion in streamflow over mined longwall panels that were less than two years old. Normal stream discharge was measured over panels more than two years old. Most apparent hydrologic dewatering impacts appear to be temporary, and the most vulnerable areas for these impacts are hill sides.

Jan 1, 1986

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007

By D. R. Bomberger

An automatic microscope has been developed to .measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed.

Jan 1, 1963

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By Robin B. Steven

Rio Tinto's Kennecott Bingham Canyon Mine is one of the largest open pit copper mines in the world. In 1988 they completed a $400 million project using a conveying system to transfer the ore from an in-pit crusher to the concentrator. The longest conveyor, C-6, was 17,352ft long and ran in a tunnel through the mountain-side to the concentrator. The belt was removed after 14+ years after carrying 700 million tons of 10 minus ore. The paper discusses the original G6 belt's performance and new splicing methods used to achieve a 60% dynamic splice efficiency on the replacement belt.

Jan 1, 2004

By Violetta Pavlova

Knowledge of geometrical properties of blocks in a hard jointed rock among other things is of considerable importance for prediction of rock mass behavior and for its exploitation. This paper presents a new approach to obtain the information about percentage of blocks with desirable geometrical properties in a jointed rock mass extending through a large region of interest. A model of a rock mass separated by finite number of systems of parallel plane discontinuities which form discrete blocks is discussed. A computational procedure has been derived to analyze the volume and shape distribution of blocks in the rock mass.

Jan 1, 1992

By Robert W. Buechley, Charles R. Key, Jonathan M. Samet, Marion V. Morgan, Arnolfo A. Valdivia

INTRODUCTION The Uranium Epidemiology Study at the University of New Mexico was initiated in 1977 with the objective of assessing health effects of uranium mining in the Grants, New Mexico, area. The planned approach was a cohort study of mortality that would capitalize on the availability of health records at the Grants Clinic. During the first year, emphasis was placed on determining the feasibility of the proposed study: Were adequate records available? What was the quality of available information? Could a cohort be established? The first year's work confirmed the study's feasibility (Buechley, 1979). Subsequent efforts have focused on the health and exposure data base and comprehensive follow-up. A retrospective cohort study of early miners is in progress; a prospective cohort study of miners who began working under the current Federal standard is planned. This report will summarize the current status of the Uranium Epidemiology Study. A chronology of the study's activities follows (Table 1). TABLE 1. Uranium Epidemiology Study Timetable 12/77 Official start of study. 12/77-8/78 Abstracted Grants Clinic records of 21,780 persons examined for mining companies from 7/57 through 12/76. Checked company personnel records to establish who had worked underground 1 year or more through 12/76. 7/78- Obtained physical exam and mining history information on qualified miners from Grants Clinic and companies. 9/78- Obtained working level month information from companies and other sources. 12/78- Checked qualified miners list with New Mexico death tapes and New Mexico Tumor Registry files. 9/80- Submitted qualified miners list to Social Security Administration for search of its records. 12/80- Obtained copies or abstracts of early State Health Department and Mine Inspector's reports. 3/81-4/81 Conducted Pilot Respiratory Disease Survey. 3/81- Verified underground status of qualified miners via company personnel records. 3/81- Verified smoking and mining histories of qualified miners via Grants Clinic records. 3/81- Began establishing cohort with first underground experience after 1970. 4/81- Checked qualified miners list with Post Office, Voter Registration Office, Motor Vehicle Division, telephone directories, city directories, and other sources. BACKGROUND Uranium Mining in New Mexico The Grants, New Mexico, uranium belt measures some 110 by 25 miles in Cibola, McKinley, and Sandoval counties (Kelley, 1963). The three chief mining districts are, from east to west, Laguna, Grants, and Gallup. Average annual production was about 5,500 tons, or 45% of United States uranium, from 1966 through 1978. Despite a drop in this figure in 1979, to 40%, New Mexico still leads the nation in uranium reserves and production (Hatchell, 1981). In 1918 carnotite, a yellow uranium vanadate, was identified in the Shiprock area (Chenoweth and Learned, 1980; N.M. Energy and Minerals Department, 1981). It received little attention at the time because of its apparently limited volume. In 1950 an important uranium outcropping was discovered by chance in limestone at Haystack Butte, northwest of Grants. In 1951 deposits were discovered in sandstone at Poison Canyon, north of Grants, and at Jackpile, northeast of Laguna. In 1955 finding of radioactive cuttings at an abandoned oil test site near Ambrosia Lake led to drilling and discovery of the first underground deposits (Melancon, 1963). Ore bodies were also found near Church Rock in the 1950's (Rautman, 1977). A uranium rush followed. At various times during 1952-1962, 60 mines and 5 mills were in operation (Gay, 1963). In the early 1960's the price of uranium fell, and many miners left the area. Subsequent market fluctuations have produced shutdowns and consolidations, development and expansion. Many early uranium miners came to New Mexico with

Jan 1, 1981

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By Someswar Kesh, Gavin J. Faulkner

Introduction Powered supports in longwall mines essentially operate under two conditions: 1. Static (non-working) 2. Dynamic (working) There is a variety of static conditions which may exist in a mine. These may include a temporary stoppage of work for a few minutes or stoppage of work for days because of strikes or lack of demand for coal. Studies on pressure behavior were made during brief stoppages of work (few hours) as well as a long stoppage of work (two weeks). In dynamic conditions, the pressure variation on supports is expected to follow a certain pattern. However, in many cases that does not happen. Pressure-time characteristics of each leg of the supports were studied. This paper discusses the research findings of the studies made on powered support pressure behavior under both static and dynamic conditions. Studies on Pressure Variation in Static Conditions It has been noted (Brenner et a1.,1975) that the pressure distribution on mechanized longwall faces is random in nature and changes with time and position along the face. Figure 1 and Figure 2 show the distribution of support pressures for the front left leg of supports in two different mines. In both the cases it can be seen that the variation of the support pressures along the face is indeed absolutely random. However, the nature of randomness in both the cases is very different. The data in Figure 1 (Mine 1) is much more random than the data in Figure 2 (Mine 2). This can also be seen from the standard deviation of the data (81 26 Pa versus 4000 pa) . By comparing the results of ten other sets of data the same conclusions can be arrived at. Since it was found that in Mine 1, the pressure on support legs was extremely random, batches of ten supports each were taken and the mean pressure plotted. This mean pressure line is shown in Figure 1. It was expected that this would smooth out the variation due to individual props and reveal a better picture of the support pressure distribution. For the case cited, the standard deviation is lowered to 5043 Pa from 8126 Pa which indicates that, on an average, the supports tend to take loads more uniformly, however for individual support legs the load on the supports is very random. The significance of this is that, if the supports are selected on the basis of theoretical load calculations alone (based on the roof block concept or some other concept), only the mean value of the support load required will be known. In the case of a pressure distribution with a high standard deviation, some supports selected on the basis of mean value will fail, while others will be supporting low loads. Hence, for proper selection of support capacity, it is not only necessary to know the average load but also the expected nature of the distribution. The only reason why the supports are supporting the roof in Mine 1 well is the fact that the yield load is above the highest level of load attained. If Mine 2, which has a much higher average load, had the same sort of standard deviation, the loads on the individual legs could easily exceed the support load. For example, if the pressure distribution followed a normal curve and the mean pressure was 36,700 Pa with a standard deviation of 9000 Pa, it is possible that 67% of the supports will be within the pressure range of 36,700 plus or minus 9,000 Pa, or 22,700 and 45,700 Pa. Many of the supports could then exceed the yield load of 40,000 Pa. It is clear then that the mean load is an inadequate criterion for estimating support resistance. The nature of the problem is statistical and such an analysis should therefore be made as far as pressure data are concerned. Statistical Analysis of Pressure Data. In general, in longwall mining and other geo-mechanics studies, it is extremely difficult to specify the exact nature of the distribution of a variable. Under these circumstances, probability

Jan 1, 1986

By D. J. Frey

While costs of most commodities and services have increased markedly over the past 25 years, the cost of electricity has steadily declined. One of the reasons for this price decline is the improved efficiencies of generating plants which is shown in Fig. 1. 1,2 Another reason for this is the decline in coal production costs. Efficiencies for the best plant increased from about 32 percent in 1540 to about 40 percent in 1962 and then decreased slightly to 38 percent in 1965. The increase in efficiency for all plants (US average) has been even more notable, progressing from less than 15 percent in 1940 to about 32 percent in 1965. The chief reason for the improved efficiency is the change in operating steam temperatures. These increased about 12 F per year until 1200 F was reached in 1962. At this high temperature excessive corrosion of super-heater and reheater tubes was experienced and steam temperatures were dropped back to 1050 F and even 1000 F in some cases. To successfully compete against other energy sources for generating electricity, this corrosion problem must be solved so that operation at higher temperatures and thus, increased efficiencies will be possible.

Jan 1, 1967

By SAMUEL A. LOLON, ADITYA JUGANDA, JURGEN F. BRUNE, JR. GREGORY E. BOGIN

Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosive methane-air mixtures, herein referred to as explosive gas zones (EGZs) [1]. The risk of mine explosions can increase if these EGZs migrate out from the gob into the surrounding mine entries — a phenomenon known as gob breathing. A number of 3D computational fluid dynamics (CFD) simulations using various magnitudes and periods of barometric pressure variation have indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. Early-warning systems with real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

By Jürgen F. Brune, SAMUEL A. LOLON, ADITYA JUGANDA, Gregory E. Bogin Jr

Historically, there have been many occurrences ofmine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosivemethane–airmixtures, herein referred to as explosive gas zones (EGZs). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Fluctuating barometric pressure is the common cause for EGZs outflowing or outgassing from the gob. Numerical analysis using a 3D computational fluid dynamics method was developed to fully understand the outgassing phenomenon. A number of simulations using various magnitudes and periods of barometric pressure changes indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. An early warning system with a real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

Aug 24, 2020

By Wu Chao, Wang Pinglong, Meng Tingrang

This paper discusses the research results of sulphide ore properties with respects on self-heating and the assessment techniques on mine spontaneous combustion for several mines of sulphide ores in China. A group of experimental devices for testing the chemical behaviour of sulphide minerals, the geological structures, the rate of oxygen absorption, the initial self-heating temperature, and the ignition point of ore samples, etc. are also described in detail. These methods have been proved to be effective by several sulphide mines which all have the history of spontaneous combustion of sulphide ores. INTRODUCTION A fire disaster from the spontaneous combustion of sulphide ores in a mine can produce large quantities of toxic gases and heat to pollute the working environment, lead to large economic losses and loss of human life, and even compell the mine to be closed. Some mines of copper, lead, zinc, tin and iron in China are of high content of sulphur. It is of great importance to evaluate the potential of spontaneous combustion of sulphide ores before beginning to design and mine the ore deposits. At present, the mechanism of spontaneous combustion accepted commonly is that sulphide ores undergo slow oxidation on exposure to moisture air at ambient temperature, with the evolution of heat, gases and moisture. The heat generated, if not dissipated, gives rise to an increase in the temperature of the sulphide ores. As the temperature of the sulphide ores rises, the rate of oxidation increases. If this is allowed to proceed unchecked it can eventually result in the ignition of the sulphide ores. For pyrite (FeS2), it reacts with oxygen and water according to the following equations.

Jan 1, 1993

By F. Calizaya, I. Duckworth

An ore-pass is an underground conduit used to transfer ore from one level of a mine to another. This method of transportation depends on the elevation energy only; therefore, it has very low operating cost. However, two inherent problems may hamper this process: (1) hang-ups of interlocked pieces and (2) a sudden release of trapped air from the ore-pass (belching). These events can create unsafe conditions with the potential for catastrophic consequences. This paper presents a summary of CFD modeling studies that were formulated to investigate the pressure build-up and belching of dust and rock particles from long ore-passes. The models were calibrated against field data collected from an actual ore-pass system and used to predict the airflow-pressure distributions in the mine for various ore feed rates and ore-pass geometries. P.T. Freeport Indonesia’s Grasberg ore-pass system (240,000 tpd capacity) was used for this purpose. This system comprises of four active ore-passes, with each being more than 600 m in vertical length.

Jan 1, 2004

By P. Zhang, W. D. Xiao

"A process mineralogy study was conducted to guide the development of a process for the extraction of vanadic oxide (V2O5) and aluminum compounds from bone coal and its ash as well as the production of byproducts. Results show that to extract the targeted metals at higher recovery rates, one must find a suitable agent capable of destroying the structure of the mica and breaking down the lattices in which these metal-bearing minerals occur. For such minerals, metal extraction efficiency is usually low if the approach is simply adding an oxidant that cannot destroy the structure. In this research, a byproduct fluosilicic acid (H2SiF6) at 20 percent concentration from an operating phosphate fertilizer plant was found to be powerful and effective for the leaching of vanadium-bearing minerals such as mica. This environmentally friendly process improved the leachability of valuable constituents in the bone coal significantly, with the leaching rate of V2O5 increased to 94 percent, from 83 percent, and that of aluminum oxide (Al2O3) increased to 75 percent, from 40 percent. X-ray diffraction and chemical analyses showed that the structure of mica can be destroyed using fluosilicic acid either alone or in combination with sulfuric acid. Based on the process mineralogy study, a processing flowsheet was tested, which resulted in a final V2O5 powder product with purity of 99.2 percent and an overall recovery rate of higher than 85 percent. The flowsheet consists of leaching, ion exchange and ammonium precipitation. With this process, various byproducts could also be generated, including aluminum fluoride, cryolite, aluminum sulfate, calcium sulfate, ammonium chloride, sodium chloride and cement admixtures.IntroductionVanadium is an important rare metal broadly used in the production of steel alloys and nonferrous alloys as well as in the chemical field as a catalyst. Vanadium-bearing bone coal and clays are abundant in China, and they contain other valuable metals such as aluminum. Bone coal is a type of carbonaceous shale. The vanadium-bearing minerals mainly exist in mica, kaolin, iron oxides, tourmaline and garnet. According to previous studies (Xiao, 2007; Xu, 1989; Xu and Chen, 1991; Ji and Xu, 1991; Chen and Xu, 1992; Xu and Heng, 1992), vanadium occurs from the isomorphous substitution of V3+ for Al3+ or Fe3 + in the crystal lattices of mica, tourmaline, garnet, dolomite and aluminosilicate minerals. In iron oxide and kaolin minerals, vanadium appears as an adsorption form. The isomorphous substitution of vanadium is more stable in tourmaline, garnet and silicate minerals. Therefore, vanadium in bone coal may exist in three phases: vanadium-containing kaolin and oxides, vanadium-containing mica, and tourmaline and garnet (Xu and Chen, 1993; Xu and Zhang, 1993; Xu and Wang, 1994; Feng, et al., 2005; Lin and Fan, 2001)."

Jan 1, 2015

By S. Tuylu, D. Adiguzel, A. Bascetin, E. G. Savas, O. Ozdemir

"Paste Technology has some advantages comparing to other surface disposal methods. With this method, it is possible to pump high concentrated solid materials to very long distances without segregation problem. However, it is known from Literature that pumpability of materials is completely related to rheological properties of the materials. For this reason, in this study, the rheological parameters (e.g. yield stress and viscosity values) of the paste material prepared from Pb-Zn tailings at various solid ratios (60-85%) were obtained in order to determine the pumpability of the paste material. Additionally, slump tests, which are usually used in mining industry, was carried out. Finally, regression analysis was made between the slump values and rheological parameters of the paste material to find a correlation between two independent parameters. The results showed that there is a great correlation between the slump values and the yield stress of the material. On the other hand, there was no correlation with viscosity: ty=430.28-16.877Sv (R2= 0,94; ty: Yield Stress (Pa), Sv: Slump Value (cm)). Based on the results obtained from this study, it can be clearly concluded that the slump values obtained from a simple test can be used to predict yield stress values of paste materials. INTRODUCTION Recently, surface disposal of mining tailings has become one of the biggest problems in mining industry in terms of environmental issues. Therefore, several researches have been focused on this subject in order to find a best solution or method for this problem. These studies showed that paste technology has some advantages compared to other conventional methods. Tailings thickened to the extent show no segregation of particles during transportation, and relatively small amount of settling occur post-deposition which are often called “paste” (Cincilla et al. 1997). Paste tailing technology has two applications in the industrial area as underground paste fill and surface paste disposal. Paste tailing technology was first started to be used in Grund mine, Germany in the late 1970s (Grice, 1998). Process tailing material, water and - if needed - cement materials, which are the components of the paste, must be blended to obtain a homogenous mixture suitable for pumpability. Consistency behavior of the paste material is determined using a conventional sedimentation cone concrete test (slump). Meanwhile, the slump value of the paste must be between 200 and 250 mm for surface applications (Newman et al., 2001). Additionally, in the case of underground paste system, the optimum slump value must be between 150 and 200 mm. On the other hand, the water content and density of paste at certain slump value change depending on the amount of fine particles in the tailing sample. While moisture of the material will be high, its density will be low because of surface area of particles which increases with decrease in particle size (Meggyes and Debreczeni, 2006). For pumpability of the paste to long distances, slump value of the paste must be good enough to be accepted for use of surface paste disposal. Paste material has a yield stress because they show non-Newtonian behavior and generally is classified as a Bingham plastic fluid. (Cooke, 2008; Theriault, 2003). In addition, the appropriate viscosity value of the paste along with the yield stress must be between 100 and 250 Pa (Bascetin et al., 2013; Bascetin et al., 2014; Bascetin et al., 2015)."

Jan 1, 2016

By D. R. Spears, D. A. Stanley

The US Bureau of Mines investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed and solids concentration on the kinetics of shear-flocculation. The results showed that shear flocculation is a two-stage process. In the first stage, which occurs during the first 1-2 min. of the reaction, the mean particle size increases rapidly, and in the second stage, an equilibrium is set up between the rates of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear flocculation, which was dependent on solids concentration and collector dosage. This stirring speed was the minimum necessary for particles to overcome the electrostatic energy barrier, and that results in keeping the conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1995