Search Documents

By Liuming Wu, Willis Forsling

The complexation of Alizarin Red S (ARS) at the surface of hydrous fluorapatite particles has been investigated at 25.0 C by means of potentiometric titrations, adsorption experiments in 0.1 M NaCI ionic medium, and Diffuse Reflectance Infrared Fourier Transform spectroscopy (DRIFT) studies. A chemical model describing the reaction at the aqueous mineral surface has been established under equilibrium conditions according to the reaction [== -CaOH2 + HA2 - « _ =PO CaA2 - z + H30&apos;; to (int.) = -5.61 ± 0.02 3 a =PO- logBs-1110(int.) ( ) within the range 8.40 <_ -log[H ] <_ 9.80.] Experimental data were evaluated using the computer program FITEQL on the basis of a constant capacitance model for the electric double layer. The surface complex structure, has been proposed to involve the quinoid and alpha phenolic oxygens of ARS coordinated to the calcium sites on the fluorapatite surface.

Jan 1, 1993

By Lyda W. Hersloff

As decommissioning of various radioactively contaminated facilities begins, the question of appropriate residual surface contamination becomes an issue. Surface contamination can result in exposure to people via inhalation, ingestion, and external radiation exposure, There is therefore the potential of exposure to workers involved in the dismantling of a facility as well as members of the general public acquiring salvageable equipment, tools, and building materials. The levels established as acceptable for unrestricted use by national and international organizations vary by as much as an order of magnitude for certain radioactive materials. The calculated doses associated with some acceptable contamination levels can be significant. The principle of ALARA, as low as reasonably achievable, is therefore a necessary element in establishing surface contamination levels for a specific site. Some components in evaluating site specific surface contamination levels for unrestricted use, especially removable contamination, include evaluations of the historical use of a facility, the mixtures of radioactive materials a&sociated with surface contamination, and resuspension factors for various materials.

Jan 1, 1991

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.&apos; Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.&apos; The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The US Bureau of Mines (USBM) and Amax Coal Co. studied surface coal mine overburden blasting near four steel and one PVC pipeline of 15 to 51 cm-diam (6-20 in.-diam), monitoring vibration, strain and pressure. Unlike tests of small blasts simulating construction, these were up to 1 t (2200lbs) per delay in 31-cm (12-in.) blastholes. Worst-case comparisons showed that 12.7 cm/sec (5 in./s) blasting vibrations produced strains about one fourth that of pressurization and 10% to 18% of the ultimate tensile strength. No failures occurred from blasting as close as 15 m (50 ft), which produced vibrations over 60 cm/sec (24 in./s).

Jan 1, 1995

By William A. Hustrulid

The subject of surface mine development is large. This section covers the fundamental concepts involved in both the open pit mining of thick or steeply dipping deposits as well as the strip mining of thin, shallow, and relatively flat-lying seams or beds. Design involves the marrying of geometries, ore and waste characteristics, equipment, and economics so that the desired result is achieved. Generally, there are many possible combinations from which to choose. For example, extraction over a short time period requires one strategy while quite another is applied for longer times. Variations in supply and demand require some flexibility of operation. Customer requirements impose certain constraints regarding the set of possible designs. Over recent years, planning and operating considerations for surface mining imposed by environmental requirements have increased markedly. There have, at the same time, been enormous advances made in the design aids available to the mine planner. Computer simulation of the various options, whether it be for mine design or equipment selection, provides detailed information for decision making in real time. A significant challenge to the engineer/planner is how to best use the aids avail-able. Because of the widespread use of commercially available and in-house computer software by industry, this section does not deal with the details of planning (for basic coverage of mine development, see Section 7). Rather, some of the basic concepts are stressed. The principles involved in equipment sizing and selection are discussed. A highly important but sometimes over-looked aspect of planning, haul road design, is also covered. For surface mining operations of the future, in-pit crushing and conveying will become even more important. Some of the considerations for application evaluation are included. The section concludes with some future concepts for surface mining.

Jan 1, 2008

By Jozef S. Stachulak

Inco Limited operates 11 underground mines in the Sudbury District. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55,000 tons per day. Over 40 surface fans have been installed since the late 1960&apos;s. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30 years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 to 330 (cubic metres per second), with motors from 100 to 2500 hp. Fans of the axial flow type have been in common use for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages. The surface area taken up by a typical vertical fan installation is generally about one quarter of that with a horizontal fan of the same capacity. (1) This is not a problem with isolated fans and flat surface outcrop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly favour vertical fans. MAIN FANS INSTALLED There are 43 main surface fans in operation at 11 mines. Twenty-seven of these fans are supply units, and 75% of them are vertical installation. The remaining 16 units are main surface exhaust fans, with predominantly horizontal installation. Within the last five years, some 20 main booster fans have been installed underground at several mines. Axial flow fans, with adjustable pitch blades, are used for both surface and underground installations. Exhaust fans are equipped with stainless steel or cast aluminum blades. Main underground fans are arranged horizontally and the majority of them have a floating shaft between the fan shaft and the motor. (2) The size of the fans in service varies from 1.8 m to 5 m in diameter, with the majority ranging from 1.8 to 2.5 m. The pressure produced by these fans varies from 0.25 kPa to 2.0 kPa. At Inco Limited, two main fans in parallel are preferred, rather than a single fan, so that if one fan fails, the remaining fan can still supply up to 70% of normal air quantities, while the damaged fan is repaired. This requires closure doors on each of the fans so the fan can be isolated in case of failure. It is more expensive than a single fan, but results in less production interruptions. The fan installations are well away from sharp inlet and outlet bends. FAN DESIGN INTEGRITY Both the mine operator and the fan manufacturer must understand that the main fan is critical to the mine operation, and that everything technically possible must be done in design and manufacture to ensure the highest degree of reliability. Some of the design parameters and criteria, based on Inco experience, are outlined and discussed below. RESONANT FREQUENCIES AND HOUSING MODEL ANALYSIS Any fan assembly will have many different resonant frequencies. It is a challenge to the designer to arrive at a design in which forcing frequencies do not coincide with any of these resonant frequencies to produce unacceptable vibration levels in operation. Finite element analysis is a useful tool that can be used to identify the most critical of these, so that housing and blade stiffness can be adjusted to change any resonances that might be close to forcing frequencies. Shaft critical speeds should be at least 25% above the fan operating speed, and there should be sufficient separation between other resonant and forcing frequencies to avoid excitation that might result in high vibration levels. QUALITY ASSURANCE Radiographic Blade Examination Mine fan blades are normally cast in small lots. To ensure that the castings are sound, a full radiographic examination is recommended in the highly stressed lower 1/3 of the blade.

Jan 1, 1995

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

Introduction Surface mining is a business, and the objective of most businesses is to make as much money as possible within certain responsible constraints. Businesses normally measure their potential to make money by estimating the discounted cash flow rate of return on new projects or the net present value for ongoing projects. These estimators of profitability are calculated using the following well-known equation: [ ] where i is the year, n is the total number of years, A, is the after tax net cash generation in year I, r is the discount rate and NPV is the net present value. In its simplest form, when the value of r makes the NPV equal to zero, the discounted cash flow-rate of return (DCF-ROR) is defined. The maximum economically recoverable reserve is identified at the point where the NPV or DCF-ROR is at a maximum. Depending on the measure used (DCF-ROR or discount rate) for calculating the NPV, the definition of recoverable reserve will be different for exactly the same deposit. Maximization of the measure of profitability and the economically recoverable reserves should not be separated from the mining method and sequence of exploiting the reserve. The surface mining methods may involve multiple-pass development of the resource, mining to the ultimate limit in one pass or a combination of the two methods with backfill. Multiple-pass development When planning a multiple-pass mining operation, it is important to determine the width of pit expansions that are appropriate for a specific situation. Production personnel typically want wide, open work areas where operations can be set up to run at peak efficiency. While this is understandable, the trade-off between highly efficient production operations and an overinvestment in stripping should be carefully weighed. As long as safety is not compromised, a few cents per bank cubic yard increase in operating cost due to lower productivity by working in more confined spaces may well be offset by a decrease in the overall short-term stripping requirements. A mini study on productivity and cost should help quantify this cost before deciding on minimum phasing requirements. The bigger challenge associated with establishing smaller work areas is securing operations and management buy-in to marginally lower productivity when reporting results. When cost reduction is the important management goal and everyone is focusing on unit costs, one sometimes loses sight of the goal of total cost management and, even more importantly, maximum profitability. The first pit should be defined by the first grouping of recoverable mineral that has the highest after-tax unit value and forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. 1 is constructed for a rate of production, R, and a quality management strategy, Q, by calculating the NPV for a series of sequences, with each sequence assuming that the operations are terminated on successively lower profit pits. These values are plotted to form the curve in Fig. 1. If the operation ceases on a pit that has too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have made more money invested at the discount rate than by mining the next pit expansion. Therefore, the maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV. There may be an opportunity to refine the definition of the "ultimate pit" around the maximum-value point. The precise definition of the ultimate pit early in the mine life may or may not be important today, depending on how far off in the future these limits will be reached. By the time an operation must decide on its last increment of economically recoverable reserve. much of the

Jan 1, 2000

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930&apos;s. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By J. S. Gardner, J. J. Zaluski

I. INTRODUCTION West Virginia has a long history of coal production.1 The state at one time led the nation in total coal production, while at the same time coal from West Virginia constituted one quarter of total U.S. coal production.2 In more recent years, however, West Virginia’s level of coal production has been reduced in comparison to that of other states due to the high relative cost of producing coal in the state.3 Another blow to the producers of coal in West Virginia is the action known as Bragg v. Robertson.4 In 1998 various individual plaintiffs, as well as a conservation group known as the West Virginia Highlands Conservancy, filed a civil action under a provision of the Surface Mining Control and Reclamation Act of 1977, Pub. L. No. 95-87, §522, 91 Stat. 445 (codified at 30 U.S.C. §§1201-1328) ("SMCRA" or the "Act") that allows declaratory and injunctive relief against state and federal officials for non-compliance with the Act.5 The plaintiffs generally claimed that the Director of the West Virginia Department of Environmental Protection ("WVDEP") had exhibited a pattern of violating mandatory non-discretionary duties under SMCRA and the West Virginia state regulatory program.6 These non-discretionary duties involved many areas of regulation, including water quality standards, disturbance of wetlands, hydrologic reclamation plans, Approximate Original Contour ("AOC") requirements and AOC variances, post-mining land uses, contemporaneous reclamation, and as explained later, the "buffer zone rule."7 In addition to these claims against WVDEP, the plaintiffs also alleged that certain individual members of the Army Corps of Engineers (the "Corps") had failed to carry out statutory duties under the Clean Water Act (the "CWA") and the National Environmental Policy Act ("NEPA").8 Generally, the complaint stated that the Corps did not have statutory authority under the CWA to regulate valley fills created for the purpose of the disposal of waste material, i.e., the overburden associated with mountain top mining.9 Alternatively, the plaintiffs claimed that even if the Corps could regulate valley fills, the Corps violated NEPA by issuing nationwide permits without required analysis. Finally, the plaintiffs asserted that the issuance of a nationwide permit for surface mining valley fills is unlawful.10

Jan 1, 2001

By Irwin H. Reiss

Gentlemen, the title of my paper is Surface Mining An Interim Land Use. Surface mining has become one of the major controversies of our time. This has happened in spite of the fact that all surface mining to date has involved only 6 million acres out of a total of 2300 million or approximately one-fourth of one percent of the total land area in the United States. I&apos;m not going to dwell on whether peoples&apos; perspectives are out of focus in light of the area involved, the energy crisis, national security, or the international balance of payments problem. While these things are all critically important, it is not the function of this paper to relate to them. Maybe the amount of attention attracted to surface mining is out of proportion to a lot of other things, but I don&apos;t feel that we should use that as a basis for procrastination. However, let me categorically state that anything that affects the surface of the earth is a form of land use --- be it an interstate highway, a power plant site, a golf course, a corn field, a strip mine, or the plot of ground on which your house is located.

Jan 1, 1974

By Don Cchultz

The United States Forest Service, as a land managing agency, is responsible for the surface administration of National Forest lands. The basic objectives of management are protection and utilization of renewable resources such as water, forage, timber, wildlife, recreation, and clean air. Much of the National Forest land in this country is open to mineral prospecting and development. When large de-posits of minerals are extracted from the forest environment, especially by surface methods, there are oftentimes conflicts between accepted mining methods and the objectives of other resource management goals. Such is the situation in Southeast Idaho where several members of the phosphate industry are operating on and adjacent to the Caribou National Forest. In 1966, the phosphate industry and the Caribou National Forest became mutually concerned with the problems of rehabilitating mined areas and minimizing potential damage to adjacent forest areas. A Cooperative Administrative Study was initiated with industry supporting the Forest Service financially and with equipment, material, and manpower, as well as interest and enthusiasm. The objectives of the study are to provide basic, applicable information pertinent to: 1. Protecting the quality of water emanating from mined water-sheds. 2. Providing for soil stabilization on mined areas. 3. Returning mined areas to surface resource production. 4. The feasibility of making mined areas esthetically acceptable. It was concluded that the following separate--yet intergrated--fields should be studied in order to obtain the desired information:

Jan 1, 1971

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By F. J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for those of us in the coal industry -particularly in Asia -the preponderance of the power plants being planned or under construction designed to use coal as the power plant fuel. This has produced a significant increase in the demand for steam coal, which has in turn encouraged many of us in the industry to develop new coal mines. One country that has enjoyed very substantial growth in coal production is Indonesia. This developing country of 195,000,000 people who live on the nearly 13,000 islands of Indonesia have emerged very quickly to become the third largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface mining methods. This paper will examine the surface mining of coal in Indonesia, as it continues to be an important part of the supply equation for coal in Asia.

Jan 1, 1996

By R. Singhal

Canada&apos;s coal production is approximately 65.4 million tonnes of which 95 % is produced by surface mining methods mostly from the three Western provinces (British Columbia, Alberta and Saskatchewan). The mines are highly mechanized; productivity gains during the past few years have ranged from 60 -80%. Truck/Shovel methods are common although Saskatchewan lignite is almost exclusively mined by draglines. This paper provides an overview of Canadian Coal mining industry vis a vis surface mining. Emphasis is on application and utilization of mining equipment and associated mining methods.

Jan 1, 1994

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974