Search Documents

By D. T. Kirkwood

The practice of impounding mine water and liquid fine waste in underground mines is increasing. Often these underground impoundments are created by constructing seals or bulkheads designed to withstand the expected hydraulic pressures. Occasionally seals are built for another purpose, usually to act as explosion-resistant ventilation barriers. Due to factors such as clogged drain pipes or unexpectedly high inflow rates, these explosion-resistant seals sometimes become subjected to hydraulic pressures. The incidence of seal failures due to inadequate design and/or construction is also on the increase. Fortunately, to date, no lives have been lost by water seal failures, but a clearer understanding of the design and construction considerations specific to water seals is vital to keep this from occurring in the future. This paper presents technical considerations for the design and construction of seals which will specifically be required to withstand hydraulic pressures in underground mines.

Jan 1, 1995

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By Elmer R. Drevdahl

During the last few years there has been a rapid increase in the development of the community or junior college throughout the United States, Some factors behind this development include the need for more college facilities to service the growing number of high school graduates, the desire of the public to provide some post high school education at reasonable costs, and the need to provide post high school educational opportunities not now provided by most of the universities and colleges. Many of the new community colleges provide at least three educational services including local opportunity to provide the first two years of a four year college program, two year technical-vocational programs of a terminal nature, and adult educational opportunities. The community college has the advantage of not being saddled with years of academic tradition which prevent it from changing to suit the educational needs of the community It serves. The flexibility of the community college in developing new programs, particularly in the technical areas, is going to provide industry with many of the badly needed technicians it is now unable to secure.

Jan 1, 1965

By A. P. Chaves, A. Gomes

The cyanidation and adsorption processes at Fazenda Brasileiro mine were studied with the aim of increasing hydrometallurgical recovery. Technical evaluation of the processes consisted of (i) quantitative mineralogy of ore samples collected in different points of the circuit, and (ii) comparison of plant performance in the original (designed CIP) and in the modified (current CIP/CIL) circuits. An empirical correlation between process variables and gold grades in the cyanidation tailings was established. The suggested modifications in the circuit and in the operation conditions led to an increase in gold recovery, from 91 to 93.5%. Annual revenue is expected to show an increase of approximately US$ 1 million.

Jan 1, 1998

By Feng Dingwu, Chen Jin, Sun Zhongyuan, Peng Shiying

The recent development of rare-earth permanent magnets has impacted the field of magnetic separation. The permanent magnets technology led to the advent of various magnetic separators particularly designed for application in mineral processing. In this paper, a new type of rare-earth PHGMS possessing a higher magnetic field strength in the working zone was developed using finite element analysis techniques. The NdFeB permanent magnets used had properties of 38 MGOe stored energy, and magnetic material flux levels exceed 1.2 T, The combination of scientific and engineering design and suitable matrices can offer an effective separation of industrial minerals, such as kaolin, feldspar, etc. Compared with conventional high intensity electromagnetic separators, the equipment can reduce electrical energy over 80% with lower operation and maintenance costs, and less installation space.

Jan 1, 1995

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By J. B. Hiskey

Introduction The domestic copper industry has suffered for some time from declining ore grades; rising costs associated with conventional mining, milling, smelting and refining; tightening environmental restrictions; and shrinking markets due to materials substitution. Ore grade depletion is a major problem. It is illustrated by the decline in average copper yield shown in Fig. 1. From 1979, copper grade has dropped 60%, lowering yields from 1.2% to 0.49% (Sousa, 1981). The US copper industry is taking drastic measures to enhance its competitive posture and to guarantee its future worldwide position. In a sense, this involves a general restructuring of the processing philosophy of US copper producers. Judging from recent trends, this restructuring relates to the application of solution mining techniques to the treatment of copper ores and low grade waste material. Recovering copper by leaching techniques has been practiced for centuries. As early as the mid-16th century, some Hungarian copper mines were recycling copper bearing leach solutions through waste heaps (Nash, 1912). In the US, recovering copper from dilute mine waters has been carried out for more than 100 years. There are, however, certain technical innovations that have elevated the importance of solution mining as a process for copper recovery. These include: • Advances in solvent extract-electrowinning (SX-EW); • Developments in acid and acid ferric cure processes for oxide and mixed oxide sulfide ores; • Improvements in heap and dump construction; and • Advances in in situ leaching technology. Generally, solution mining enjoys certain intrinsic advantages over conventional mining and milling. Compared to conventional milling, the combined capital and operating costs of leaching facilities are normally lower, start-up times are faster, and the leaching operation usually has less impact on the environment. Furthermore, solution mining represents an expedient way of extracting metals from small shallow deposits, and is particularly suited to the treatment of low grade sources. And, in the case of waste dump leaching, there is a tremendous resource in-place that has the mining cost already off the books. This paper updates current US copper solution mining trends. Solution mining systems Schlitt (1980) summarized the characteristics of the principle leach systems in the US. He pointed out that the wide variations in copper deposits make solution mining a more site-specific activity than conventional mining and milling. Heap leaching is usually selected for moderate to high grade ores having a copper mineralization that is amenable to acid leaching (oxides, silicates and certain sulfides). Higher grade ores mined specifically for heap leaching are usually treated to optimize copper extraction, therefore, crushing and some pretreatment (acid curing) may be justified. On the other hand, dump leaching practice usually involves leaching low grade waste rock placed on large dumps as dictated by topography and haulage costs. Mine waste is therefore treated in an uncrushed run-of-mine condition. Finally, in situ leaching is appropriate for either very deep ore bodies or for recovering copper from low grade rock left behind in abandoned pit walls, stopes, and subsidence zones from earlier mining activities. True in-situ solution mining should be defined as the leaching of ore in its original geologic setting. Heap leaching Heap leaching has a long history as a hydrometallurgical process for copper recovery. The methodology of heap leaching established at Rio Tinto in Spain more than 300 years ago is basically the same as that used today. Processing concepts, such as solution management (sprinklers and leach/rest cycles) and copper

Jan 11, 1986

By Pascal Deschamps

"INTRODUCTION During the last decades, many underground facilities for the storage of hydrocarbons have been excavated worldwide and the technology is fully mature. Similarly to other underground structures, the initial basic design has to be adapted along with the work progress, in order to cope with the actual site conditions and in particular the geology, hydrogeology and associated rockmass quality. In addition, Client’s or underground Contractor’s constraints (such as resources availability, schedule or cost impact) may vary from design to construction and require last minute adjustments. Engineers are required to introduce flexibility and anticipation of unexpected situations (similar to the above-mentioned) while conceiving large underground facilities. Although most of the cases require only minor adaptations, crucial parts of the facility have sometimes to be considerably modified and reviewed. This article will present four cases evidencing how the design of one of these essential structures - the concrete plug – has been adjusted during site implementation without impairing the initial performances. Hydrodynamic containment The product containment of the unlined caverns discussed here is ensured by the principle of hydrodynamic containment. A permanent water flow is naturally or artificially maintained with an orientation toward the storage cavern and then, neither product-tight membrane nor lining are required. The hydraulic gradient (and the associated water flow lines), being directed from the surrounding mass toward the cavern, prevent from outward migration of the product. If the hydraulic gradient is not sufficient or if the water table is evidencing instability, water can be artificially injected into the rockmass through purpose-built boreholes, drilled from dedicated galleries. This water injection system, called the water curtain, is generally located several tens of meters above the level of the cavern. This principle is illustrated here after."

Jan 1, 2016

By N. B. Greninger, M. J. Sapko

The US Bureau of Mines conducted, through joint funding with the Colorado Mining Association, large scale oil shale rubble fire tests to investigate flammability characteristics and different methods of extinguishment. Ignition of large rubble piles was easily accomplished. Foam blankets could be used to control surface flames. The results of these large scale tests confirmed that water was effective but not particularly efficient in extinguishing deep seated oil shale fires. It took up to 1.7 times as much water to extinguish afire as anticipated on the basis of a simple cooling model, assuming 100% utiliza-

Jan 1, 1991

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Abstract-Since 1982, the US Bureau of Mines has inves¬tigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (<_1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars he provided only in mines >_1.07 m (42 in.). However, court obtained variances are granted to mines <_1.22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1989

By J. Guzman

Introduction The Carlin Trend is North America&apos;s premier gold producing district. It is located in northeastern Nevada&apos;s Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km&apos; (386 sq miles) in and around the Carlin Trend and own all or part of I6out of the 19 mines and prospects identified to date. Since the initiation of Newmont&apos;s exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont&apos;s Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output. The same incentives produced even more spectacular exploration results. In each of the last five years, net additions to reserves and resources outpaced current production by substantial margins. These facts demonstrate the spectacular past prospectiveness of the Carlin Trend and the success of focused, multi-disciplinary exploration methods that made it possible to more than offset the recent accelerated depletion of gold resources. However, is this situation sustainable? How long can the mining companies along the Carlin Trend keep on finding resources faster than they deplete them? These are some of the questions that motivated this study. The authors have not quantified the future potential for gold exploration in the Carlin Trend nor established a deposit discovery path. But strong indications were discovered that the [ ] Carlin Trend remains a relatively immature exploration district and that the potential for significant new discoveries is high. Methodology and data The approach chosen to address the above questions was simple. The authors compiled deposit size data, measured in contained ounces of gold resources, for all known deposits along the Carlin Trend (Table 1). The resource information was obtained by adding cumulative historical production (adjusted for mining losses and metallurgical recovery) to 1989 year-end published resource inventories. In a mature exploration area, where most deposits have been discovered, this distribution would be expected to approximate lognormality and would plot along a straight line on a lognormal probability scale. This result was found in previous work by Allais (1957) and recently confirmed by Cox and Singer (USGS, 1986) in regard to various types of mineral deposits in several regions of the world. It was also found to hold true for oil and gas pool size distributions (Arps and Roberts, 1958; Kaufman, 1962; McCrossan, 1969). [ ] The data used were compiled by Newmont Exploration geologists. The purpose of the study is to make inferences about the underlying geologic processes in the district and the maturity of the exploration effort. Therefore, deposits were not classified according to ownership but according to geologic occurrence as known from current information. Newmont&apos;s Post and Barrick&apos;s Goldstrike and Betze deposits, for example, are shown as a single occurrence to reflect the actual geologic setting. The cumulative frequency distribution of deposit sizes was plotted on lognormal probability paper (Fig. 2). The abscissa shows the cumulative fraction of deposits at or below a certain deposit size and the ordinate shows the deposit size in thousands of ounces of contained gold resources.

Jan 1, 1992

By R. K. Mehta, S. K. Dhar, R. R. Mallepali

Introduction The incentives for developing a distributed form of the comminution model include: • for describing the heterogeneous comminution behavior of multiphase mineral systems (i.e. realistic ore bodies, such as complex sulfide ores consisting of chalcopyrite, galena, sphalerite, pyrite and siliceous minerals) and •for generating, for various locked and free particles, in situ, microscopic, breakage behavior such as the mode of fracture (intergranular vs. transgranular), the relative rates of breakage and the breakage distribution. However, the computational difficulty and the effort made in estimating a large number of parameters (Andrews and Mika, 1975; Wiegel, 1976; Herbst et al., 1985, 1988) do not justify the utility of this approach. Also, obtaining the results experimentally is very tedious and time consuming if using this approach. Although recent work in this area (Choi, Adel and Yoon, 1987; Mehta, Adel and Yoon, 1989, 1990) showed good results for liberated particles, the quality of the estimation and prediction was poor for locked particles. Attributing this to the complex breakage behavior of locked particles, it was concluded that additional constraints, and possibly modification in the breakage distribution functional form for locked particles, were necessary. However, further mathematical analysis revealed that the method previously used was in error. The purpose of this technical note is to present the correct solution methodology used in solving the general model equations of a multicomponent mineral system containing multiple classes of locked particles. Previous work and connection The general form of the comprehensive, distributed-component comminution model has been described as (Herbst et al., 1985) [d (m (0) -[ I - B ] S_ m(t) = A m(t) (1)] where [A] is the fundamental matrix/state companion matrix, commonly referred to, in the comminution literature, as the "mill matrix." Note that for a distributed-component comminution model, this is a full, general, real matrix, unlike a lower triangular matrix for a simple grinding model or a lumped-binary grinding model with one locked-particle class (Herbst et al., 1985, 1988). Also note that all of the underlined letters refer to matrices. Herbst et al. addressed the difficulty in arriving at a closed form of the analytical solution of Eq. (1) via similarity transformation [IT J inv (T)]]. This difficulty occurs for several reasons: •[A], as a general real matrix, may have complex eigenvalues and complex eigenvectors. •More importantly, there is no guarantee that a set of eigenvectors of [A] will turn out to be independent. An attempt was made to solve this problem by implementing a decomposition method. With this technique, the mill matrix was decomposed into a sum of lower and upper triangular matrices [(i.e., A = L + U)]. Then the solution was obtained using similarity transformation (Mehta, Adel and Yoon, 1989, 1990). [e(At) = e(L+U)t = e(Lt).e(Ut) _ [ TL Jt- (t) inv(T_L)] [-Tu Ju (t) inv(Tu)]] [But, unfortunately, e 1+U = e t . eu is true only for scalars and not for matrices (i.e., eL+u# eL- eU) unless they commute. In other words. eAt = e(L+u)t= ekt - eU&apos; if LU = UL. Hence, this decomposition scheme must be replaced by a mathematically acceptable method known as the "splitting method"]

Jan 1, 1994

By R. H. King

Recently, the North American mining industry experienced a severe recession, forcing managers to take dramatic steps to cut costs and compete in the difficult international market. Some of these steps were closing mines, reducing work forces, renegotiating wage agreements, and purchasing the most productive equipment. Managers are now looking beyond these traditional avenues and are focusing more on advanced technology. In the present environment, it is essential that mine operators obtain the maximum use of capital expended on equipment. However, mine workers do not obtain maximum efficiency or productivity from equipment because the adverse and hazardous mine environment impedes human performance. Also, the efficient use of large, complex machines calls for levels of precision that many times are beyond the capability of even highly trained miners. A possible solution to this problem is a machine that mines without operators - autonomous mining machines. However, numerous problems confront researchers who are attempting to develop such equipment. Some mining tasks are not always composed of a series of cyclic motions readily performed by factory floor robots. In addition, mining takes place in the geological environment where conditions are highly variable and unpredictable. As a result, these machines must be able to sense and adapt to variations in operating tasks and environment. Considerable autonomous vehicle research has been completed, especially for defense. However, autonomous vehicle (AV) technology has not advanced to practical application yet (King, 1988) and mining research is necessary in areas: representing mining specific knowledge; •analyzing and reasoning about sensor data in the mining environment; and •discovering completely new mining methods or new approaches to existing methods that become apparent when we remove the constraints imposed by the necessity of human operators. A specific machine, the LHD, can be used to show the problems for researchers who are attempting to develop autonomous machines for mining. This author chose the LHD because it can borrow concepts developed for autonomous navigation by military programs. But considerable mining research is also required. Furthermore, studies done at the Henderson mine, in Colorado, show autonomous LHD &apos;s promise cost and safety benefits (King, 1988). At Henderson, LHDs load ore from draw points, tram to an ore pass, dump and return, or switch to another draw point. An autonomous LHD must sense vehicle position along the route, relate sensor data to stored-map information, to determine location, follow drift center lines, plan paths between dump position and initiate appropriate control commands, sense vehicle operating status and vehicle health, key on features or targets for special tasks like high speed turns, perform end of travel tasks (loading and dumping), and detect and avoid obstacles. These goals are similar to those for shuttle cars, trucks, and front-end loaders. Therefore, much of the technology is transferable. Each Henderson LHD extracts six to 40 dippers from each of a series of draw points. The LHD transports the ore to an ore pass within 55 m (180 ft) of the draw point, making the longest round trip 110 m (360 ft). The LHDs have very fast hydraulic dumping and loading systems that reduce the round trip cycle to less than one minute. Even though the LHD is capable of 500 trips per shift, the average production is 300 dippers. Man trip and lunch reduce available operating time to 6.5 hours per shift. Mucking difficulties (setting large boulders aside), operator breaks for activities like talking shop, and cleaning and smoothing roads further reduce operating time. Supervised autonomy can reduce the number of operating units by increasing operating time per shift since computer controlled machines can operate during lunch and between shifts and reduce operator errors. If dippers per shift increase from 300 to 350 (long-range goals are 500 dippers per shift), constant production requires only 10 operating LHDs and two spares. Manpower requirements drop from 24 to four by controlling five machines from one workstation. A review of technology available from the Autonomous Land Vehicle, the Advanced Ground Vehicle Technology, the Ground Surveillance Robot, and other programs, show the following differences between others work and mining industry needs: •If we focus initially on mobile haulage vehicles, we can navigate from a map. We do not need to explore. •We can modify the environment to reduce the navigation requirements. •We have a harsher environment than any of the research programs have encountered. •Our equipment must operate faster and more precisely than present AVs. •Our equipment must operate reliably over long periods of time. •We must have better onboard machine health monitoring and diagnostics. •The AV programs do not address geosensing. •The major AV programs are not cost-effective. For example, we cannot afford the computer power for robust image processing, yet. To computer control an LHD, we must replace the guidance and monitoring skills of experienced operators with sensors, computing hardware, interfaces, and several software mod¬ules. Experienced operators avoid collisions and load efficiently in piles that may contain oversize muck. Collision avoidance without an operator requires sensing all obstacles in the draw

Jan 1, 1991

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state&apos;s permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should consider handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 12, 1983

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calculations where the compliance limit of lbs SO2/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equations to blend to an SO2 content of 1.2 lbs SO2/million Btu, the excess sulfur for Coal A was defined as Sulfur excess% = 0.5 - 0.6*13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C[<] 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: •W is the total weight; •A, B and C are the fractional proportions of each potential blend stocks; •Sa, Sb and Sc represent the percent sulfur content of the blend stocks; •Ha, Hb and Hc represent the calorific content of the blend stocks in Btu/lb; and •H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1998

By D. Gu, B. Lin

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1994