Search Documents

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By Robert Underwood, Boleslaw Tolwinski

In 1965 Helmut Lerchs and lngo Grossmann presented to the mining community an algorithm to find the optimum design for an open pit mine. In their words, "the objective is to design the contour of a pit so as to maximize the difference between total mine value of the ore extracted and the total extraction cost of of ore and waste." They modeled the problem in graph theoretic terms and showed that an optimal solution of the ultimate pit problem is equivalent to finding the maximum closure of their graph based model. In this paper. we explain how a dual simplex algorithm can be used to solve the same problem. We show how this algorithm is closely related to Lerchs and Grossmann's and how the steps in their algorithm can be viewed in mathematical programming terms. This analysis adds insight to the algorithm of Lerchs and Grossmann and shows how it can be simplified.

Jan 1, 1996

By M. Rancourt, J. Levay, D. K. Murphy

INTRODUCTION The LG-2 project is one element of the La Grande Complex, an integrated development of hydro-electric potential being constructed in north-western Quebec by the James Bay Energy Corporation. The project is located on the La Grande River about 65 miles east of Fort George on the James Bay coast and 600 miles north of Montreal. It comprises a 525 foot high dam, 81,000 feet of dykes, spillway and river diversion works and a 16 unit underground powerhouse that will have an installed capacity of 5,328 MW. The power installations at LG-2 represent approximately half of the total potential for the complex. When completed in 1982, LG-2 will rank as the largest underground powerhouse in the world. Studies and site explorations for the project were begun in 1971, construction commenced in 1973 and the roll date for the first machine is scheduled for February, 1980. GENERAL ARRANGEMENT OF POWER INSTALLATIONS As shown in Figure 1, the power installations are located on the south bank of the river about 4 miles downstream from the main dam. The general arrangement of the complex is presented in Figures 2 and 3. The intake structure consists of 2 groups of 8 gated intakes separated by a central service area. Sixteen 26 foot diameter in-

Jan 1, 1976

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Richard Giffen, Michael Trabold, Pablo Lemus

"As part of the new 2nd Ave Subway Project, an existing tunnel constructed in the 1970’s will be connected to the new subway and used as new running tunnels. The existing tunnel had to be modified to comply with newer structural and fire life safety codes and to be connected to the new cut and cover station at 96th St. This paper will discuss the complexities of tying an existing tunnel constructed over 40 years ago into the new station and allowing for movements due to the unloading of the existing tunnel and the differential settlement of the two structures during both the construction and permanent condition. Topics that will be discussed include structural analysis, ground improvement techniques, selection of support of excavation walls, working in contaminated soil and instrumentation and monitoring of the structures. It will also cover retrofitting the tunnel to comply with updated Fire/Life/Safety requirements. PROJECT OVERVIEW The Second Avenue Subway (SAS) will be the first major expansion of New York’s subway system in over 50 years. To be constructed in four phases, it will run from 125th St. in Harlem to Hanover Square in the Financial District (see Figure 1). For most of its length, the alignment is directly under the Second Avenue roadway."

Jan 1, 2016

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022

By I. A. Kunasz

This paper is not intended to review and re-state general information on lithium, but rather to analyze the paradigm that has caused such a rapid rise in lithium production and the development of new lithium producing centers. Details on pegmatites, brines, concentrate and chemicals are amply covered in a number of publications ? SME?s Industrial Minerals and Rocks, Industrial Minerals, Roskill and a host of other publications. There is no question that the latest interest in lithium has been driven by the potential development of the electric car. This stimulus prompts one to recall two symposia: 1. ?Lithium Resources and Requirements be the year 2000?, organized in 1976 by the U.S.G.S. in Denver (1) and the sequel 2. ?Lithium ? Needs and Resources? at Corning, N.Y. (2).

Jan 1, 2011

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By J. van Oldenborgh

The world market for bunkers represents some 140 MT (1980) of marine fuel oil and distillates. This is equivalent to 23CMT of coal, a potential market for steam coal larger than the total seaborne trade of steam and metallurgical coal today, and an obvious area which could contribute savings in world oil consumption. Oil bunkers are lifted fairly evenly throughout the world, the main supplying regions being Western Europe, the Middle East, North and Central America and Japan (Figure 1). Not surprisingly, the main customers are the tankers representing about 50 percent of the world market - (95 percent of the Middle East Market) - dry bulkers represent some 30 percent and general cargo ships the rest.

Jan 1, 1982

By Paul S. Murphy, Eric W. Oehrke

INTRODUCTION The global market for sulphur has experienced dramatic structural shifts during the past 10-15 years. After a number of years of dominance as sulphur suppliers, the world's Frasch producers were confronted with large increases in nondiscretionary sulphur production from sour crude oil and gas, while escalating energy and exploration costs reduced the economic incentives to replace dwindling sulphur reserves. Sulphur demand also experienced substantial growth, but the majority of this increase was filled by nondiscretionary production. The result was essentially flat demand for Frasch sulphur during this period. This paper briefly summarizes Freeport Sulphur Company's outlook for global supply and demand for sulphur through the year 2000, and examines in more detail the history and anticipated shifts in trade patterns. World trade in elemental sulphur (brimstone), despite year-to-year fluctuations, has been on an upward trend in recent years, and should continue to grow through the end of this century. The type (discretionary vs. nondiscretionary) and location of forecast sulphur supply sources has potentially broad implications for the world's Frasch producers, as they compete in a world market which is increasingly supplied by non-discretionary production. SULPHUR DEMAND Sulphur is a versatile and essential element used in a wide variety of manufacturing processes. Almost 90% of world sulphur consumption is in the form of sulphuric acid. The relatively low cost, ready availability, and physical and chemical properties of sulphuric acid make it the most economical acid for a number of chemical processes. Although sulphur is used in the manufacture of many products, the largest consumer by far is the phosphate fertilizer industry. The majority of sulphur demand growth over the past 30 years has occurred in this area, and today it accounts for nearly 65% of global sulphur consumption in all forms. Due to the relative importance of phosphate fertilizers, sulphur demand is typically discussed in terms of fertilizer and non-fertilizer (or industrial) uses, and this approach will be followed here. We at Freeport believe that global consumption of phosphate fertilizers should grow at an average annual rate of about 3.5% through the year 2000, which is roughly equal to the growth rate experienced during the past ten years. The basic assumption underlying this forecast is that world population will continue to grow significantly, while the total acres of cropland will grow only slightly. Therefore, in order to feed a growing population, higher crop yields will be necessary, which in turn will require the increasing use of fertilizers. This expected growth in phosphate consumption will, without doubt, fluctuate from year to year, and we Frasch producers have painful memories of the large dip in demand during 1982-83. However, we believe that the fundamentals for growth are very good, and that future demand will move back onto the historical trend line. In the recent recession the use of sulphur in the non-fertilizer or industrial sector dropped sharply, and it now appears that future growth will not return to the old trend line. Most of the non-fertilizer uses of sulphur and sulphuric acid involve older industries which are very mature, such as oil refining, steel, pulp and paper, pigments, etc. The use of sulphur in some of these industries is expected to exhibit little or possibly even negative

Jan 1, 1986

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010

By Christof Brewka

Los Pelambres, 200 km north of Santiago, Chile, is the latest in a series of mega-projects developed in this part of the world. While most of its predecessors are spread over open desert, the Los Pelambres mine is nestled inside a narrow alpine valley high in the Andean Mountains. To handle the daunting task of transporting the mined copper ore more than 12 km and 1,400 vertical meters downhill to the concentrator plant, a gigantic belt conveyor system (capacity of 8700 mtph, 1800 mm wide ST 7800 steel cord belt, 2.5m diameter pulleys, an elaborate braking system including a mechanical failsafe and large reducers with a total installed drive power of 25,000 kW) has been employed. Many of these components have pushed the limits of conventional belt conveyor design.

Jan 1, 2000

By Remo Grandori, Fabrizio Antonini, Giorgio Dolcini

The paper describes the anticipated and the encountered geology, the TBM selection concepts and the machine special features, the tunnel sections, the achieved advance rates and the geological problems, the machine behaviour and the main setbacks caused by ground conditions the Authors also discuss the scopes for possible improvements to double telescopic shield machines, with special reference to their application under extreme geological conditions such as those that were met in the course of Los Rosales Tunnel excavation.

Jan 1, 1991

By D. S. Bubar

This presentation will represent a diversion from the central theme of Cordilleran geology, in both time and space, as we move 2,000 miles east of Spokane to eastern Canada, specifically the province of Quebec, to discuss a major new Archean-age volcanogenic massive sulphide deposit called Louvicourt. The deposit is located in the Val d'Or camp in the prolific Abitibi Greenstone Belt some 400 miles north of Montreal. It was discovered by Aur Resources in June, 1989 on a property operated under the terms of a joint venture with Louvem Mining, a Quebec company controlled by Ste. Genevieve Resources Inc. of Montreal. As a geologist, I am proud to be able to describe Louvicourt as a geological discovery, as it was found by doing systematic deep diamond drilling based on a geological concept. The deposit is essentially blind from surface and lay undiscovered for the 10 years that the Louvem mine was in production just 2,000 feet away from its easternmost workings.

Jan 1, 1991

By X. Zhu, R. Du Plessis, J. D. Miller, D. G. Kotylar

Research on the low-potential hydrophobic state of pyrite with potassium amyl xanthate (PAX) as collector, is reported to help explain and understand the fundamental aspects of the N2TEC flotation process, which was originally developed for the improved recovery of gold from refractory auriferous sulfide ores. Typically in the N2TEC process, air is replaced by nitrogen as the flotation gas, and potassium amyl xanthate is used as collector for the reactive auriferous pyrite particles. The first N2TEC flotation process was commissioned at Lone Tree in Nevada in March 1997 and has been in operation ever since. On the basis of electrochemically controlled contact angle measurements, the low-potential, low-pH hydrophobic state of pyrite has been examined as a function of flotation variables such as pH, gas-phase composition, collector concentration and pyrite potential.

Jan 1, 2000

By E. Kurt

The field of percussion rock drilling is subdivided into two areas of application; that which takes place on the surface and that which takes place underground. Surface drills are used in quarrying, highway construction, and maintenance work; underground equipment in mining and tunneling work. Two basic principles are involved in the operation of all percussion drills. First, the principle that reciprocates the impacting piston and second, the principle that causes the drill steel and bit to rotate. The back and forth motion of the piston is accomplished by a self-acting automatic valve that admits air alternately to each end of the piston (Figure 1). Drill steel and bit rotation is imparted by an integral ratchet mechanism (Figure 2) in the so-called "rifle bar" machines (Figure 1) or by a separate pneumatic motor in "independent rotation" drills (Figure 3). While rock drills are subject to all kinds of physical and operational abuse, they are most sensitive to faulty lubrication. Proper lubrication is the single most important factor in the longevity of a percussion drill.

Jan 1, 1970

By H. O. Seigel

This is an introductory paper on a new method of prospecting for mineral deposits which has been developed by Scintrex Limited. The method, which we call Luminex, for luminescent mineral exploration, is based on time- resolved mineral luminescence created by an ultraviolet light source. It has the ability to detect and resolve a group of key minerals which are either ore minerals themselves, or more often, are accessory or pathfinder minerals for certain types of economic ore deposits. Fortunately, these minerals are commonly found at the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits which are remotely detectable from the air to include those such as tungsten, tin, molybdenum, gold and bedded lead-zinc deposits and, is therefore, a natural supplement to our three classical methods of airborne geophysics.

Jan 1, 1983

By G. Jeffrey Taylor

The environment at the lunar surface is drastically different from the one we are used to on Earth. The Moon has one-sixth of Earth's gravity, virtually no atmosphere, a surface bathed in radiation and micrometeorites, large temperature gradients, low seismicity, and a dusty, rubbly surface. To successfully mine and process materials on the Moon and to mitigate degradation effects in the hostile lunar environment, these factors require new designs for equipment and development of new techniques and technologies.

Jan 1, 1990