Search Documents

By Y. Wang, E. Forssberg

Wet magnetic separation methods for the recovery of hematite and chromite fines and ultrafines were investigated. These methods included wet high-intensity and high-gradient magnetic separation, carrier or "piggy-hack" magnetic separation, magnetic field-induced aggregation and magnetic seeding. This investigation indicated that wet magnetic separation is more efficient for fines and ultrafines. This investigation also indicated that other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behavior of these minerals with respect to the magnetizing field, temperature and particle size is also presented.

Jan 1, 1995

By Y. Wang

Wet magnetic separation methods for recovering hematite and chromite fines and ultrafines are investigated in this paper. These methods include wet high intensity and high gradient magnetic separations, carrier or "piggy-back" magnetic method, magnetic field-induced aggregation and magnetic seeding. This investigation indicates that wet magnetic separation is more efficient for fines and ultrafines whereas other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behaviour of these minerals with respect to magnetizing field, particle size and temperature is also presented.

Jan 1, 1993

By Alexander E. McHugh

A study of some variables affecting the recovery of molybdenum from oxidized molybdenum minerals was made. The effects of variations in contact time, temperature, pulp density, particle size, and solvent concentration on the recovery of molybdenum using acid and alkaline solvents were investigated. Chemical analyses, screen analyses and microscopic examinations were made and the presence of important elements determined. A hydrometallurgical method was developed to recover the molybdenum from the oxidized molybdenum ore by simultaneous dissolution of the molybdenum with sulfuric acid, adsorption on activated charcoal and flotation of the charcoal. The molybdenum was extracted from the activated charcoal with sodium hydroxide, precipitated with calcium hydroxide as calcium molybdate and this regenerated sodium hydroxide for additional stripping. A solvent extraction method, using mines, was also studied to recover molybdenum from both alkaline and acid molybdenum solutions. Satisfactory results were obtained.

Jan 1, 1967

By K. Gorazda

The population growth, urban and industry development cause the increased pollution with different substances, which contain phosphorus. It contributes to the increased demand for its compounds, increasing the use of its natural resources, which is considered to be the most accessible source. The forecasts regarding the world natural reserves of phosphorus deposits are saying that more than 50% of resources used currently will be exhausted within next 60-70 years (Steen, 1998). European Union formulated its goals regarding the waste management in 1990. Its main rules include prevention of waste generation, recycling, reuse of waste as the raw materials in technological processes, separate collection and optimization of final removal. The phosphorus recovery from waste is realized currently in many ways: directly from the waste water stream in sewage-treatment plant, from the sewage sludge, from animal waste, industrial waste and other emissions from industry (Przewrocki et al., 2004). According to the rules of cleaner production the waste should be treated as the source of resources for the production of products with full value (Kowalski, 1998).

Jan 1, 2005

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By Eugene F. Casey, John G. Ruggiero

INTRODUCTION Construction of tunnels in urban areas, especially reclaimed areas, pose many problems. The Red Hook Intercepting Sewer Tunnel, Contract 1A is a portion of the Red Hook Water Pollution Control Project located along the Brooklyn waterfront in New York City. This contract required the construction of a 2620 meter long (8600 L.F.), 3 meter (10-foot) diameter soft ground tunnel, eight Tunnel Manholes, nine Regulator structures, four Diversion and Tidegate structures and 765 meters (2500 L.F.) of branch intercepting sewers of diameters between .30 meters (12 inches) and 1.8 meters (72 inches). The construction contract bid price was $62 million with a duration of three years. The tunnel route crosses over five sets of operational twin cast iron subway tubes with clearances ranging from 4.3 meters (14 feet) to as small as 0.35 meters (14 inches). The route of the tunnel traverses historically interesting areas which have been reclaimed over the last 200 years. This paper is a case history describing the contractor's methods utilized to successfully advance the work through the above problem areas. LOCATION The Red Hook Intercepting Sewer Tunnel is located in the Borough of Brooklyn of New York City. The route is

Jan 1, 1981

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By J. Engesser

A research project supported by the Minnesota Department of Natural Resources and the Iron Ore Cooperative Research Committee was undertaken to reduce the dissolution of fluoride into process water during taconite processing. Leach tests were conducted using rod mill feed samples and water containing varying concentrations of calcium and sodium. Laboratory liberation grinds were performed to evaluate fluoride rejection during grinding and magnetic separation. Tube furnace tests were conducted to evaluate fluoride volatilization during pellet induration. The results indicate that fluoride concentration of process water is a function of both calcium and sodium concentration in process water. It appears that less than 1 percent of the fluoride present in rod mill feed will dissolve in process water during grinding. More than 90 percent of the fluoride present in rod mill feed is rejected with tailings during size reduction and magnetic separation. The furnace tests demonstrate that bentonite and fluxstone (calcite and dolomite) addition to taconite concentrate during pellet production increases the amount of fluoride that volatilizes during induration. Lime hydrate addition to pellets decreases the amount of fluoride that volatilizes during pellet induration. During acid pellet production approximately three times more fluoride enters the water during induration-off-gas scrubbing than during grinding. When fluxed pellets are produced three to eight times more fluoride enters the water during off-gas scrubbing than during taconite grinding.

Jan 1, 2004

By R. A. Lowe

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determines whether the clay can be utilized for paper and ceramic applications. In this work, causes of poor low-shear viscosity and methods of improving rheology have been investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 1998

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By F. J. Bruey

Refdist is a simple but valid approach to planning or analyzing a test-vs-control plant trial that uses accumulated plant performance data to calculate objective criteria for judging the trial outcome. Refdist calculations and results are explained and illustrated with data typical of the mining industry. Findings from a simulation study of Refdist statistical properties are reported. Suggestions for dealing with messy data situations are offered.

Jan 1, 1999

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By Denys B. Smith

Electric logs and cuttings records from Zechstein 3 and 4 strata in boreholes in the British Sector of have been interpreted in the light of numerous cored boreholes through this sequence in north-east England. This interpretation shows that potash salts in the two cycles are thickest and most consistent in a belt 20 to 40 km wide parallel with and a few kilometres from the present basin margin, and are here generally similar in grade to those known onshore. The potash ores in both cycles are mainly of sylvinite in onshore areas, the layered Upper the Southern North Sea Potash of the fourth cycle being rather less variable but generally of appreciably lower average grade than the Boulby Potash of the third cycle. Potash salts in both cycles are highly variable in thickness and grade in basin centre areas where they have been grossly affected by diapirism of the thick second cycle salts.

Jan 1, 1978

By James A. Pendleton

In response to Public Law 95-87 (SMCRA), Colorado promulgated regulations governing the mining of Coal. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence. All permitted underground coal mines within Colorado have approved subsidence programs. Preliminary monitoring results indicate the subsidence mechanical predictions have been sufficiently accurate to preclude material subsidence damage. The State of Colorado has developed a practical approach to regulating subsidence, which stresses monitoring verification of predicted subsidence phenomena. However, shortcomings exist in our ability to precisely predict the secondary consequences of subsidence, including effects to structures, the hydrologic balance and the environment. Lack of accuracy in predicting these secondary consequences results in uncertainty, necessitating conservatism in permitting. To avoid increasingly stringent permit restrictions, future research should emphasize the secondary consequences of subsidence.

Jan 1, 1986

By Paul J. Ehret

With the passage of the Surface Mining Control and Reclamation Act (SMCRA), and the implementation of state permanent programs, underground coal mining operations are for the first time subject to government regulations regarding subsidence. These regulations now and in the future will directly affect the manner in which mining companies mine their coal. Since the promulgation of the original final regulations by OSM, numerous changes in those regulations have been made and many additional changes are pending in the near future. This paper will discuss state and federal approaches to regulating underground coal mines and examine issues surrounding future subsidence regulations.

Jan 1, 1986

By R. Dillinger

In the environmentally conscious social atmosphere today, reclamation in surface mines has become a main issue to the public and the regulatory committees. In response to this increased attention, many regulatory committees have begun to enact more stringent regulations on surface mining operations. Operations across all spectrums of the industry have seen changes. Recently and most visibly the mountain top removal mines have seen several new regulations focusing on environmental protection. Specifically regulatory committees have emphasized a focus on the methods of reclamation and recovery of layers suitable for vegetation. These layers are the most visible once the operation has concluded. Also, these layers have the most human interaction (farming, hunting, and house development). Often times the new regulations enacted are shifting from a performance base to a standards base. The key differentiator being a performance base dictates the final result while a standards base dictates the method to achieve the result. The very nature of many regulations (especially those that are standards based) not only challenges the physical limitations of the equipment used today, they come with a financial impact. For the purpose of this paper, the model will be a surface coal operation, utilizing draglines as primary overburden movers. The coal seam is ten feet thick, the overburden ninety five feet thick, the pits are 150 feet wide, and the dragline is a Bucyrus Erie 1570.

Jan 1, 2011

By Jeffrey D. Thatcher, Debra W. Struhsacker

With the burgeoning development of precious metals heap leach mining projects throughout the country regulatory agencies are beginning to take a closer look at the short-and long-term environmental consequences of heap leach mining. This increase in regulatory review is occurring on federal, state and local levels, and is affecting both large- and small-scale mining developments. Small-scale mining developments are receiving especially critical regulatory scrutiny because in the eyes of some regulatory agencies, small developers lack the credibility automatically accorded to major mining companies. This is due in part to a bad image of small miners based upon past environmental problems and permit violations caused by a few, small operators. The proponent of a small mining development thus faces special problems during the project permitting process, and must convince the regulatory authorities of his company's ability and commitment to plan, develop, and decommission a mining operation in compliance with environmental regulations. Not only must the small developer have a thorough understanding of the regulatory requirements affecting his project, he must also devote considerable effort to careful internal planning in order to produce a well organized approach to project permitting. The importance of proper planning cannot be overstated. Project planning is key to convincing the regulatory agencies that the small miner is capable of developing a viable project. More- over, the economics of a small mining project demand permit acquisition at modest cost and in a timely fashion. A well planned permitting effort will thus ensure that permits are received within budget and on schedule. This paper will review the federal, state, and local permitting requirements for heap leach projects, and the variability of these requirements from state to state. The environmental assessment process for projects developed on public lands, and the acquisition of zero- discharge water quality permits, air quality permits, and local special use permits as they apply to small mining developments will be discussed. The paper will conclude with a review of project decommissioning and cyanide neutralization requirements and their implications for small-scale heap leach projects.

Jan 1, 1987

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By Guocheng Pan

This paper presents-:a new multivariate mineral resource estimation model, referred to as the Related. Information (RI). Instead of relating a mineral resource descriptor directly to a set of geological variables, the RI model relates the mineral resource descriptor to a synthesized information measure RI, which is created from a set of geological variables. All of the variables are transformed into binary characteristics. This model comprises two stages of estimation: estimation of a synthesized information measure and estimation of mineral resources. The information carried by a variable is classified into three types: mineralized-barren information, mineral resource variation information, and variable-controlling information. The synthesized information measure is defined as the product of the three types of information and the responses of binary geologic characteristics. The RI model is demonstrated on the pegmatitic Nb+Ta deposits in China.

Jan 1, 1992

By Kotaro Ohga, Kiyoshi Higuchi, Zhang Xun Tao

In Japanese coal mines, drivage works of in-seam gate roads are mainly carried out by blasting methods. Changes of methane concentration in gate roads are recorded by centralized monitoring systems in general. To obtain useful information from the recorded data, authors analyzed changes of methane concentration for 3 hours after blastings. As a result, the changes of methane concentration with time can be divided into five distinct patterns. It is thought that appearance of the each pattern depends upon the geological conditions of the surrounding of the headings. Therefore, we attempted to confirm such observations by simulations using mathematical models.

Jan 1, 1989