Search Documents

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By Walter M. Chapman

The National Lead Company operates its MacI tyre Development at Tahawus, New York for the production of ilmenite and. magnetite. The heavy ore of titanium and iron is mined from the open pit mine at an average rate of 7,000 tons per day, and the development waste is removed at an average rate of 10,000 tons per day. The mine working benches are spaced, at 35-foot vertical intervals, and 6 ½ inch blast holes are drilled 39-feet deep with 18-foot burden and spacing by down-the-hole drills. Waste is loaded with a 6 yeard shovel and ore with 2 ½ yard shovels into 22-ton rear dump trucks. A good account of the history of MacIntyre drilling and. blasting was presented to this assembly two years ago, by F. R. Jones. (1) Most of the blasting since the start of the mine in 1941 was done with 90% gelatin dynamite until 1955, when relatively insensitive canned blasting agents were adopted.. In 1956, 9-inch blast holes drilled with down-the-hole drills. In 1956, also, the first experimental trials of prilled ammonium nitrate fertilizer and fuel oil (hereafter called fertilizer) was made following the lead of Cleveland-Cliffs operations in the Hibbing district. Since that trial did not, as some local skeptics predicted, make grass grown on the bluff, but resulted in a well-broken shot, further tests were conducted in dry holes. I Observations of those tests indicated that the fertilizer did its share of the work. If anything, it produced better fragmentation than the normal load di in neighboring wet holes.

Jan 1, 1958

The first of this three part series examines he history and some of the properties and characteristics of explosives. Use of explosives is discussed for underground and surface coal operations—the largest consumers in the mining industry. Part two of the series will deal with explosives use in surface and underground hardrock operations. Part three will discuss explosives transportation, storage, handling, and destruction.

Jan 7, 1981

By Harry Deitzer

Within the industrial marketplace barium sulfate has an established role as a filler or extender pigment for use in a wide array of applications. The focus of this paper is to outline a number of these applications and in each one characterizes those features of barium sulfate which provide value. Following this is a discussion of the process techniques which have been used to develop value from a selected class of barite ores found in southern Missouri. It is appropriate to define some terms which may help in clarifying some concepts as presented. Use of the term barium sulfate refers broadly to the chemical compound BaSO4 Barite will generally refer to the naturally occurring barium sulfate ores and their properties. Barytes, whether bleached or not, will refer to barite ore made suitable for industrial applications.

Jan 1, 1993

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By R. W. Amstutz

Abstract. The shaft was drilled on U.S. Government land in the Piceance Creek Basin and was funded by the U.S. Bureau of Mines. It was drilled to 723 meters (2 371') to provide access to rich deposits of oil shale, nahcolite and dawsonite for geotechnical test work and environmental mining research. Rotary drilling and dual string, reverse-air, jet-assist circulation methods were used. Drilling required 8 months. Site preparation, running and cementing the casing required another 4 months. A 2.44-meter (96-inch) ID steel welded casing, 5.1 cm (2 inches) thick was installed and 2 700 tonnes (63 000 sacks) of cement were slurried and pumped into the annulus.

Jan 1, 1980

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By James E. Friant

The technology applied to shaft sinking has lagged far behind other construction activities. While surface oriented construction and mining have made great strides with new processes and equipment, the majority of shafts sunk currently still follow a drill, blast and muck-out cycle developed in the 16th century. Today, in 1979, the shaft sinking industry is in the midst of its own private industrial revolution. Millions of dollars are being spent annually by industry and government alike to spring the art of shaft sinking into the 20th century. The objective of this paper is to review a few of the newest mechanized schemes for shaft sinking. This is not a theoretical review, however, but a practical one, and deals only with hardware and projects which are currently on jobsites. Figure 1 shows the equipment. On the left is the 241SB 184, a 24 foot diameter blind shaft borer. This machine is currently at about 200 feet, constructing a coal mine shaft in Alabama. It is built and utilized in a manner similar to a tunnel borer. In the upper center is the 1211SR, a 12 foot diameter blind shaft reamer. This machine follows a 6 foot pre-drilled blind pilot hole, and is at work in Chicago. On the upper right is the 121BR, a powerful new blind drill. Just below it is the conical drill head for the 121BR which can utilize either carbide or standard disc cutters. At the center bottom is an expandable back reaming head which can be used to enlarge a drilled shaft up to a maximum of 16 feet diameter, or can be used to produce a shaft having several diameter changes. This equipment is also in use in Chicago.

Jan 1, 1979

By Don Runge, John T. Zeni

Cuprex Limited is currently developing a small gold mining operation in Central Australia in the Tennant Creek field. In February 1984, the company undertook a feasibility study on the project and operations commenced in August 1984. Ore reserves are located between 230 and 280 metres (755 ft and 919 ft) below surface and ore extraction required the establishment of a shaft network for access, ore hoisting and ventilation. Zeni Drilling Company from West Virginia, U.S.A. was contracted to blind drill two shafts for the project. Blind drilling was selected for various reasons, including timing which related to cost efficiency. The blind drill shaft technique has proved successful in this application and with enthusiastic and innovative support from the mining industry, will prove an efficient and cost effective means of accessing and operating underground mining projects of all sizes in the future.

Jan 1, 1987

One of the critical challenges facing the mining industry ? and not just in the United States ? is the looming labor shortage. A significant percentage of the industry?s professional workforce is, well, getting old, and many will be retiring in the next 10 years or so. This is not a new issue to the industry. It has been discussed at various industry meetings and conferences for many years. How does mining, with its largely negative public image, attract young people to mining schools? And, equally important, who is going to teach them? Mining schools, what?s left of them in the United States, are beginning to lose qualified faculty to retirements, and no one is available to replace them. SME addressed this issue during the keynote session at its annual meeting in February in Denver, CO. This year?s theme was ?Mining: It?s About the People.? Despite a blizzard that blanketed the city on the day most attendees were to have arrived, the meeting still attracted a record 7,202 people. And the accompanying exhibit sold 822 booths, also a record. The U.S. Department of Energy?s National Energy Technology Laboratory contracted with the National Academies? National Research Council to complete a study concerning the availability of skilled workers to meet the energy and mineral security requirements for the United States. The National Research Council, in turn, asked SME to collect and analyze workforce trends in these industries. The result of SME?s analysis is the report ?Emerging Workforce Trends in the U.S. Energy and Minerals Industries.? It is available on the SME website, www.smenet.org. Click on Government Affairs. While the report did not paint a completely dismal picture, there were some disturbing results. It concluded that within 20 years there will not be a sufficient number of skilled professionals to satisfy the labor demand. That said, the report said that most of those positions would likely be filled. However, the U.S. mining will go through a period of time when the workforce will be made up of very young and senior workers.

Jun 1, 2013

By Don Fisher, Jean Juilland

Introduction A section of the Federal Land Policy and Management Act of 1976 specifies the procedure for areas the US Bureau of Land Management manages that have wilderness qualities. In part, FLPMA specifies that within 15 years of its approval, the Secretary of the Interior shall review roadless areas of 20 km2 (5,000 acres) or more and roadless islands of public lands identified during the inventory as having wilderness characteristics described in the Wilderness Act of 1964. Further, the Secretary shall report to the President his recommendation as to the suitability of each area or island for preservation as wilderness. However, before any recommendations for, wilderness designation, mineral surveys shall be conducted by the US Geological Survey and the US Bureau of Mines to determine if any mineral values are present. And finally, a Presidential recommendation for wilderness designation becomes effective only if so provided by an Act of Congress. BLM Inventory Procedures To fulfill these legal requirements, BLM is inventorying the land it manages for wilderness qualities. Since the law sets special provisions for Alaska, BLM included in its inventory only the public lands it manages in the conterminous US. In 1980, after public input, BLM picked 967 areas to be considered as Wilderness Study Areas. All of the selected WSAs are in 11 western states and the areas total about 97,128 km2 (24 million acres). From these 967 areas, through its multiple-use planning system, BLM is making initial recommendations of areas to be considered suitable for preservation as wilderness. Those WSAs that BLM initially considers suitable for wilderness preservation will have mineral surveys conducted by the USGS and the USBM, to determine mineral values. Based on these mineral surveys and other resources information including wilderness qualities, the Interior Secretary will report to the President his recommendations on the WSAs suitable for wilderness preservation. To make the initial recommendation of suitability, BLM managers will need information about geology, energy, and mineral (GEM) resources as well as information about other resources. BLM has begun a GEM assessment program to provide its managers with that information. This program is designed to provide information for a WSA suitability decision process that aims to supply minimum necessary GEM information. In essence, the program will provide preliminary assessment of the mineral potential for each WSA. Assessing the WSAs To accomplish this, a two-phase program was designed. In phase one, only existing data are collected and used. In phase two, new data are generated and added to existing data. Phase two begins only if BLM geologists, mining engineers, or managers consider the information provided in phase one as inadequate. This avoids unnecessary work and expenses and allows the program to proceed without undue delay. Figure 1 shows the two-phase process, including BLM's GEM in-

Jan 10, 1983

By T. Diering

Gemcom PCBCTM is a software package which has been developed over the last 22 years for the planning and scheduling of block cave mines. This paper presents an update of the various research and development activities done to PCBC recently. It also provides an overview of the current capabilities of the software including tools for both feasibility type studies as well as tools for operating mines. PCBC is used extensively by prospective and operating block cave mines and some of the recent applications are described.

Jan 1, 2010

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By Ankit Jha, Javad Sattarvand, Aaron Young

Blockchain technology is one of the prominent disruptive technologies that are being implemented in several disciplines. The application of blockchains in the mining and mineral industry can provide utility to several processes especially when the industry is undertaking digital transformation. The governing principles of blockchain technology are applicable in undertaking transformation in several processes within the mining industry. This study investigates the applications of blockchain technology within the realms of the mining industry and identifies key areas of implementation. A systematic review of publications on academic platforms relating to blockchain technology in the mining industry did not retrieve a considerable number of articles. Consequently, a thorough review of white papers and articles authored by individuals on use cases within the mining industry is compiled and presented in this review article. This review article identifies all the potential areas within the mining industry where blockchains could provide value and improve processes through their implementation. The broad area of implementation of blockchains includes supply chain, traceability in spares parts, contract management, regulatory compliance and cybersecurity.

Mar 1, 2024

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017