Search Documents

By Paul H. Madsen, Victor S. Romero

The Tren Urbano project in Puerto Rico includes a 19 m diameter tunnel constructed by the stacked drift method, which involves installation of a pre-supported concrete arch using multiple tunnels. Geotechnical conditions consisted of weak rock and highly weathered, unstable alluvial soils. Due to low cover, reinforcement of the arch was required. Ground behavior ranged from firm ground to mixed-face to raveling and flowing ground. Consequently, construction of the individual drifts involved many different soft-ground techniques such as steel set supports, shotcrete support, shield tunneling, forepoling, and consolidation grouting. During construction, the design was modified to improve constructability. Although settlement was experienced during excavation of the drifts, arch movements were within predicted limits and minimal surface settlement was observed upon excavation of the interior.

Jan 1, 2001

By Phil Rice, Mohammed Nasim, Richard Flanagan

"The Gateway Trans-Hudson Partnership (GTHP), a joint venture of WSP USA, Inc., AECOM USA, Inc, and STV Incorporated, is providing preliminary engineering services to Amtrak for the Hudson Tunnel project as well as supporting the NEPA process for getting the record of decision (ROD). This preliminary engineering design effort by GTHP includes geotechnical exploration and laboratory testing, design of structures, tunnel contract packaging and procurement planning.The Hudson Tunnel Project includes the construction of a new Hudson River Tunnel system and rehabilitation of the existing North River Tunnel. The new tunnel system will be constructed south of the existing North River Tunnel, from North Bergen under the Palisades to Hoboken in New Jersey, below the Hudson River, and connecting directly to Penn Station in New York (Fig. 1). The tunnel system is configured as two single-track tubes, intermediate ventilation shafts and cross passages in compliance with NFPA- 130 requirements. The adjacent surface alignment west of the Palisades will be constructed on viaducts, embankment and retained fills. The existing North River Tunnel (Fig. 2) consists of two single-track, electrified rail tunnels extending from tunnel portals in North Bergen, New Jersey to Penn Station in New York. Completed in 1910 by the Pennsylvania Railroad, the tunnel opened at the same time as Penn Station and the four, single-track, East River tunnels that connect Penn Station to Queens and onto Long Island and New England, respectively. Both tunnels in the existing North River Tunnel were inundated with brackish river water during Superstorm Sandy (Fig. 3), resulting in the cancellation of all Amtrak and NJ Transit service into New York City for five days. After the brackish water was removed from the tunnels, the residual chlorides and sulfates have had on-going detrimental impacts on the interior concrete and rail systems."

Sep 1, 2019

By Ben Hayes, Michael Ryjevski

The Palm Jumeirah is the smallest of the three Palm Islands (Palm Jumeirah, Palm Jebel Ali and Palm Deira). It is located on the Jumeirah coastal area of the emirate of Dubai, in the United Arab Emirates (UAE). The unique man made island is built in the shape of a date palm tree and consists of a trunk, a crown, 17 fronds and a surrounding crescent island that will form a breakwater. The Jumeirah Palm Island is primarily are treat and residential area for living, relaxation, and leisure. It will contain themed boutique hotels, three types of villas, shoreline apartment buildings, beaches, marinas, restaurants, cafes and a variety of retail outlets.

Jan 1, 2007

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

By D. B. Apel

Rock mechanics software plays an important role during the design process of modern underground mines by allowing for verification of the stability of the planned excavations. The paper describes the methodology used to plan and locate the permanent underground openings at McArthur River Mine with the assistance of numerical modeling software.

Jan 1, 2004

By Pradip

Bastnaesite, a rare-earth fluocarbonate, was separated from associated calcite and barite gangue minerals in the Mountain Pass, CA rare-earth ore beneficiation plant by froth flotation using fatty acids (tall oil) collector, lignin sulfonate depressant and soda ash modifier after high-temperature (steam) conditioning with reagents. Starting with a feed grade of 7.6% REO, concentrates having a grade of 65% REO can be produced at a recovery of around 80%. A detailed investigation consisting of Hallimond tube microflotation experiments, bench-scale tests with a laboratory Denver flotation cell, and predesigned plant campaigns was made to delineate the underlying surface chemistry involved in this separation and to develop an alternate reagent scheme to enhance the selectivity of separation for this ore. Our results clearly demonstrate the superiority of alkyl hydroxamates to the conventional fatty acid collectors that were being used in the plant. Our study also indicates the possibility of achieving the desired selectivity with alkyl hydroxamates even at room temperature, thus obviating the need for steam conditioning. A critical review of the literature on rare-earth mineral flotation suggests the possibility of designing a more selective reagent combination for the beneficiation of Mountain Pass rare-earth ore, using a methodology based on ab initio molecular modeling computations.

By Nick Rose, Robert Sharon, Mark Rantapaa

Development of the Northeast Layback of Barrick’s Betze-Post open pit commenced in June 2000 and was successfully completed to a height of 400m (1,300 ft) in January 2003. Following a brief exploration drilling campaign at the toe of the final slope, in-pit waste rock backfilling commenced, which will ultimately buttress the final wall. Instability initially occurred in late 2000, above the 5040 Level, as the slope height approached 120m (400 ft). As mining reached the 4680 Level, significant deformation was experienced over a slope height of 230m (760 ft). Slope stability was managed and targeted reserve recovery was achieved by executing complicated modifications of the mine plan, including splitting layback development, well placed offloading cuts, step-outs and mid-slope waste rock buttresses. Decision on timing of these modifying events was often dictated by review of deformation magnitudes and rates determined from continuous slope monitoring records. Design modifications were developed through continuing interpretive refinement of structural geology controls and groundwater distribution, and through stability re-assessments. This document presents an overview of the geological setting and material and strength conditions of the northeast sector of the Betze-Post open pit, followed by development experience leading to design and development of the Northeast Layback. Rock mechanics modeling, design details and geotechnical performance monitoring are then presented. Development experience, stabilizing adjustments to the original design and safety procedures for development and exploration activities are described. The document is finalized with conclusions and acknowledgements.

Jan 1, 2005

By Donald K. Sparling, C. Edwin Baker

The White Mesa uranium/vanadium mill is six miles south of Blanding, UT, on the Colorado Plateau, which has historically spawned more than 200 uranium mines. As uranium prices approached an all-time high during the mill planning period, Energy Fuels Nuclear Inc. anticipated the reopening of many of these mines, whose low grade ore suddenly looked economic. The company located the White Mesa mill close to these mines, to minimize hauling distances to the mill and give vendors added incentive to reopen or expand mine operations. A receptive local community, a relatively unencumbered trip through the regulatory maze, and some mill circuit innovations all helped to make the White Mesa mill a well functioning reality. From a strategic standpoint, and to begin ore stockpiling as early as possible, Energy Fuels constructed two ore buying stations and began receiving ore in early 1977. The buying stations were located at Hanksville and at what is now the Blanding mill site. Ore receipts at Hanksville did not materialize as anticipated and the facility has since been closed. The Blanding ore buying station is now an integral part of the milling operation. All ores, whether company, vendor, or for toll milling, are received at the Blanding station. The Blanding site was central to the plateau mines, and was well received by area residents, who encouraged the introduction of industry to the area. Residents viewed mill construc¬tion as an economic blessing and were prepared to accept the associated im¬pacts. Energy Fuels hired as many local people as possible for mill opera¬tions.

Jan 4, 1981

By Jaime Adasme, Héctor González, Benjamín Celada

"INTRODUCTION Santiago de Chile is a 7 million inhabitant city which has a 103 Km long subway network operated since 1975 by Metro S.A. This network is used on a daily basis by 2.3 million people. In 2012 Metro S.A. started the biggest enlargement of the network in its history, through the design and construction of the new Line 3 (21.7 Km) and Line 6 (16.5 Km). The detailed engineering contract for civil underground works of Line 6 (L6) was awarded to the Consortium integrated by ZAÑARTU Ingenieros Consultores and GEOCONTROL S.A., in which Geocontrol was in charge of the design of 11 stations and 14.5 Km of tunnel. L6 crosses L3 in Ñuble and Ñuñoa Station, L2 at Franklin Station and ends, intersecting L1, at Los Leones Station as shown in Figure 1. LOS LEONES STATION DESIGN Location and Characteristics Los Leones Station is placed at the North end of the L6, next to the same named station of the L1 and it has four construction units, as is shown in Figure 2: I. Access Shaft (49 m x 47 m). II. Access Gallery (34 m long). III. Station Tunnel (120 m long). IV. Connection Gallery with L1 (104 m long). A singular feature of Los Leones is that the western section of the station tunnel, built from the access gallery, is located below an underground parking lot which is located in Providencia Avenue, as shown in Figure 3. It is important to highlight that the distance between the vault of Los Leones Station Tunnel and the foundations of the underground parking lot is only 6 m."

Jan 1, 2016

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat, A. J. S. (Sam) Spearing

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. Initially, ASTM A615 grade 60 steel roof bolts, which are the most commonly used bolt material in the United States, were tested with and without stresses in a simulated underground coal-mining environment for approximately six months. This paper mainly discusses the test system, protocol and system shortcomings, and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By Andy J. Robinson, Mark D. Claassen

Railroad companies and transit authorities have been slow to acknowledge that for many—utility crossings, a direct pipe installation below live rail can be just as effective as a more intrusive traditional cased crossing. Properly designed and specified pipe jacking work, and specifically pressure-balanced microtunneling, coupled with careful specification and analysis of geotechnical monitoring and, where necessary, ground improvement measures, can produce a low-risk, low ground movement solution to the needs of utility companies and municipalities whose services need to pass below urban and rural rail corridors. This paper discusses the design, geotechnical and ground improvement aspects of microtunnel crossings below active heavy and light rail lines and crossings beneath active subway tunnels.

Jan 1, 2003

By Thomas S. Kovach

In today's competitive energy market, every effort must be made to assure the lowest possible production cost. 'rhi s. paper describes the cooperative effort between the coal producer and the utility customer to develop and install a fully integrated mine information management system at a 2.5 million tpy lignite mine in east Texas. A description of each item of the modules is included along with the problems encountered during development and how they were corrected. The system configuration is also described.

Jan 1, 1989

By R. A. Meyr, K. A. Perry

Following three major mining accidents in 2006, the MINER Act of 2006 was enacted by the U.S.Congress. The U.S. Mining Safety and Health Administration subsequently released the Final Rule on Refuge Alternatives for Underground Coal Mines, which required every underground coal mine to install refuge alternatives to help prevent future fatalities of trapped miners in the event of a disaster. The following paper documents the research that was performed on a structural wall to be used in conjunction with a breathable air system to create a refuge alternative. A 103.4-kPa (15-psi) safe haven polycarbonate wall for use in underground coal mines was designed and modeled using finite element modeling in ANSYS Explicit Dynamics. The successful safe haven wall design was modeled for an actual underground coal mine environment using the explicit finite difference formulation program FLAC3D to determine the responses of the wall and surrounding strata within a mine. A full-scale design was fabricated and installed in an underground coal mine to determine any construction constraints and as a final step in proof of concept for the safe haven wall design. This paper is meant to introduce the reader to a new wall concept to be used in conjunction with current technology.

Jan 1, 2013

By Jerry W. Danni, John E. Hardaway

Corporations today must comply with an ever growing number of complex and increasingly stringent environmental laws and regulations. An environmental audit program is an effective means in which to uniformly and systematically assess compliance, and to assure management that environmental liabilities are being minimized. This paper describes the design and implementation of Homestake Mining Company's environmental audit program, which has as its primary focus the objective verification of compliance with external requirements and internal good management practices. Major elements of the audit program discussed in the paper include: pre-audit preparation; on-site audit activities; and the post-audit report.

Jan 1, 1992

By O. Guyot, T. Mulpeter

Sadiola Hill mine is located in the sub-Saharan part of Mali. In its first two years of operations, Sadiola Hill mine had already exceeded expectations with respect to profitability, plant capacity, metallurgical recovery, cash costs and social integration into the area. The advanced control system installed by the authors has been a major contributor in the substantial throughput of the mill over the design tonnage with no loss of recovery. The run-of-mine ore at Sadiola consists of soft clays with a varying percentage of grit, producing a high viscosity slurry. The percentage of grit fed to the plant varies on an hourly basis. This combination was expected to have a large impact on the milling circuit and determined that the early installation of an expert mill control system would be advantageous. Svedala Cisa OCS©, was selected as the most suitable support software. The operational rules and control philosophy are housed in the OCS© graphic-oriented fuzzy expert system while a model­based Soft Sensor has the remarkable ability to detect the variations in grit in the feed. Designed during the second half of 1996, commissioning of the system began in March 1997, the OCS was fully on-line by September. With the implementation of the optimising control strategy a throughput of 5.0 million tons relative to the target of 4.4 million tons was achieved for the 1998-operating year. The Sadiola project confirms that advanced process control techniques are among the most cost-and time-effective methods of improving metallurgical plant performance. The recipe that worked at Sadiola is a mix of metallurgical expertise, proper software selection, adequate design of control philosophy, and excellent plant support and follow­up. The early decision, design and installation of the mill control system has resulted in an enhanced Return on Investment.

Jan 1, 2000

By C. H. Stephenson, M. Du Preez

Overland belt conveyors often use vertically guided counterweight take-ups or horizontally tensioned carriages to maintain belt tension. In the event of belt or wire rope failure, these systems can release significant stored energy, creating high-impact forces that risk structural damage and personnel injury. This paper reviews current safety arresting technologies and presents a calculation methodology for estimating impact velocity, energy absorption requirements, and stroke limitations. Worked examples illustrate the selection process for appropriate arrestor types under different design constraints. The study emphasizes early integration of safety devices to minimize structural loads, avoid costly retrofits, and enhance operational reliability. Implementing robust arrestor systems improves safety and reduces downtime in bulk material handling environments.

Feb 22, 2026

By Dushasan Kundu, B. N. Shivakiran Bhaktha, Khanindra Pathak, Sarbojit Mukherjee

Mine safety and quality of life of miner working in underground mines depend to a large extent on mine illumination and communication. The provisioning of reliable, safe, and cost-effective illumination is critical, particularly in underground gassy coal mines. To prevent firedamp explosion by electrical switching operation in coal mining industry requires implementing intrinsically safe illumination circuit. The luminaire design also needs to be certified and installed properly. The current illumination systems installed inside mines require a lot of energy which is obtained from nonrenewable resources. In this work, the design and implementation of solar-powered optical fiber-based illumination are studied and implemented in the Jhanjra underground coal mine, Eastern Coalfield Limited, and a Li-Fi-based communication system for underground coal mines is proposed. Silicate optical fibers of various core diameters and numerical apertures are characterized for illumination applications and their efficiencies are reported. The possibility of achieving optical fiber-based solar, laser, and hybrid illuminations in underground mines is discussed. The design and fabrication of a Fresnel lens-based solar tracker for solar illumination are also presented. The optical fiber-based illumination system is installed in an underground coal mine and the illumination of over 70 lux is achieved at the work plane. Finally, optical fiber-based illumination and simultaneous basic Li-Fi communication are demonstrated and will be beneficial to the underground coal mining industry.

Apr 14, 2023