Search Documents

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

3.1 INTRODUCTION The final subsidence basin discussed so far is that developed long after mining has stopped. In a supercritical final subsidence basin, the central portion subsides uniformly. Thus any structures located there are not subjected to any final permanent surface deformation. But this statement is only true for the final subsidence basin. When the face is moving, the structures are subjected to dynamic deformations associated with the dynamic subsidence basin. For instance the house in front of a moving face (location 1 in Fig. 3.1) is subjected to the maximum tensile strain and the maximum positive curvahue. When it falls behind the face in location 2, it is subjected to the maximum compressive strain and the maximum negative curvature. When the house is far behind the face in location 3, it returns to its original condition with only uniform subsidence. However, the magnitude of the dynamic deformations may be sufficiently large to damage a structure in locations 1 and 2 before it reaches location 3. Therefore it is very important to study the characteristics of the dynamic subsidence basin. Under normal conditions, when the face has advanced for a distance approximately one-sixth to one-third of the seam depth from the setup entry, depending on the seam depth and the physical properties of the overburden strata, the movement of the over- burden strata reaches the surface, whereupon the surface also be- gins to deform. Thereafter, the surface point where the movement initiates is always located at a fixed distance ahead of the face. The angle between the vertical line at the faceline and the line connecting the movement initiation point on the surface and the face- line is the angle of advance influence, w. The angle of advance influence can be used to determine the distance, [ 1], which is the influence zone ahead of the face. w is approximately 20O to 35 O for the northern Appalachian coalfield (Peng and Geng, 1984). The movement of each surface point is a relatively complicated process both in time and in space, because the relative position between the faceline and each surface point varies continuously, so that the direction and rate of movement for each surface point differ. In the following sections, the movements of each surface point on the major cross section are illustrated. 3.2 DYNAMIC SURFACE MOVEMENTS Dynamic surface movements include dynamic subsidence and displacement. The movement of each point on the subsidence basin is different as the face advances from 1 to 6 (Fig. 3.2). Surface points A and B, being far in front of the moving face, subside and displace toward the face (i.e., from A to A' and from B to B'). Point C, which is quite near but in front of the moving face, subsides continuously but displaces initially toward the face and then turns to pure subsidence ending up at C'. Point D, which is behind the face above the gob, subsides continuously, but displaces initially toward the face when it is in front of the face and reverses to follow the moving face when it is behind the face, with the amount of displacement toward the face being larger than that following the face. As a result the net displacement is toward the center of the gob (i.e., from point D to D'). The same statement is true for point E. For point F, the net displacement is zero, i.e it appears to have dropped down vertically to F'. For points G to I, the net displacements are in the direction of face advance except the magnitudes are increasing in sequential order. Point 1, has reached the final dynamic position of 1'. In other words, the face has passed sufficiently away such that it does not affect the movement at point I. All other points (A to H) are still within the face influenced area. 3.3 DEVELOPMENT OF DYNAMIC SUBSIDENCE PROFILES When the face has moved for a distance of h/6-h/3 from the setup entry, surface subsidence reaches the surface. At this time the surface subsidence basin is very mild (S, in Fig. 3.3), and it is symmetrical about the center. As the face continues to advance, the maximum subsidence continues to increase, and its location moves with, but falls farther behind the face. When the face has advanced a sufficient distance, e.g., (0.9-2.2)h, away from the setup entry, the maximum subsidence reaches the maximum possible value (curve S,). At this time, the dynamic subsidence profile is fully developed. Thereafter both sides of the dynamic subsidence profile become stabilized. The subsidence profile on the face side moves with the advancing face in an orderly manner (curves S, and S,). When the face stops, the face side of the profile continues to subside and becomes stabilized (curves;) sometime after. Curve S; is the final subsidence profile (see Fig. 2.22). 3.4 DEVELOPMENT OF DYNAMIC DISPLACEMENT AND SLOPE PROFILES The dynamic displacement profile moves with the advancing face (Fig. 3.4), but changes according to some specific rules. When the face has advanced to A, the surface begins to move and its dynamic displacement profile has two maximum values (curve Ua): one positive near the setup entry moving toward the face advancing direction and the other negative on the face side also moving toward the face advancing direction. As the face continues to advance, the positive maximum displacement on the setup entry side increases and moves toward the face continuously. The same statement is true for the negative maximum displacement on the face side. When the opening increases to the critical size, both the maximum positive and negative displacements reach the peak values and remain constant thereafter. Notice that when the opening becomes critical in size, the point of zero displacement no longer moves with the advancing face. Rather it spreads into an area of zero displacement (curve Ue) and expands as the face advances. When the face stops, the displacement on the face side continues until it becomes stabilized (curve Úe). Curve Úe is the final displacement profile. The ratio of maximum dynamic to final displacement ranges from 60 to 75%. The dynamic slope profile follows the same patterns of change. The ratio of maximum dynamic to maximum final slope ranges from 50 to 80%. The maximum slope decreases with in- creasing rate of face advance (Peng and Geng, 1984). It must be pointed out that except for those near both sides of the profiles, each point on the displacement and slope profiles is subjected to a cycle of positive and negative displacements and slopes depending on its relative position with respect to the face.

Jan 1, 1992

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH's Pittsburgh Re¬search Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, which are tightly wrapped with many turns and which carry current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften, making them prone to damage. The damaged insulation reduces the life of the cable and can lead to shock, electrocution and mine fires. This paper describes a method of measuring the conductor tem¬perature of mine trailing cables during normal operation. The temperature is measured using a 50/125-, µm graded index multimode optical fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an optical time domain reflectometer (OTDR). This system is capable of measuring temperatures with an accuracy of ± I °C over a length of 4 km at I -mintervals. With this unique way of measuring temperature, tests can be conducted that simulate actual mine conditions. The tests provide important data that allows MSHA's Approval and Certification Center to develop approval criteria for cycli-

Jan 1, 2000

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

By G. Lodewijks

Today most belt conveyors used for the transportation of bulk solid materials are driven in a centralized way with all drives in one location. The dynamics of these systems has been studied since the early seventies of the previous century and are well understood. Compared to the more conventional belt conveyor system with a centralized drive station positioned at the head and/or tail of the system, a decentralized driven layout with drive stations distributed along the whole length of the belt offers a number of advantages. However, to make a decentralized driven configuration a good alternative to a centralized driven, the system designer will have to balance these benefits with the increased complexity. The full potential of a decentralized driven system can only be realized if the right balance is found between the locally applied drive force and the motion resistances occurring along the system. From previous research it was found that in a multiple driven belt conveyor system the most dominant belt behavior occurs in the belt section between the tensioning device and the first drive station. In this paper different possibilities are analyzed to improve this dominant belt response and optimize the starting behavior. This can be accomplished by changing the predescribed start up profile, starting the drive stations in sequence rather then all at the same time and altering the locations of the drive stations.

Jan 1, 2008

By W. M. Shaver, W. R. Dengler

INTRODUCTION In Canada, most of the rock being broken in underground metal mines is being carried out using traditional drilling and blasting methods. Despite advances being made in hard rock boring and other, more exotic techniques, it is Dynatec's belief that the traditional methods will continue to prevail for many years to come. It is also our belief that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunnelling businesses. Dynatec has pursued productivity improvements through the use of long rounds in both shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC 1991). This paper reviews the Craig Shaft Long Round success. This technology was subsequently utilized to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunnelling is a natural progression of the long round technology developed for the Craig Shaft. RECENT HISTORY OF SHAFT SINKING Shaft sinking is one of the oldest and most difficult mining methods. Due to the relatively small amount of shaft sinking in proportion to tunnelling and

Jan 1, 1993

By W. R. Dengler

In Canada, most of the rock being broken in underground metal mines is being done by using traditional drilling and blasting methods. Despite advances being made in hardrock boring and other, more exotic techniques, Dynatec believes that the traditional methods will prevail for many years. It is also believed that modest research efforts expended on the traditional methods will result in substantial financial benefits to the mining and rock tunneling businesses. Dynatec has pursued productivity improvements through the use of long rounds in shaft sinking and lateral development. The concept of longer rounds was developed by Dynatec on the Craig Shaft Sinking Project (RETC, 1991). This technology was subsequently used to sink the two shafts at Aur Resources with great success. The development of a Long Round Jumbo for tunneling is a natural progression of the long round technology developed for the Craig Shaft. The Dynatec Long Round System has been patented in the United States and South Africa, with additional patent applications pending in Canada and Australia.

Jan 1, 1993

By Mark N. Savit

It is indeed a rarity for a non-engineer, let alone a lawyer, to even be considered for a mining-related award, especially where that award is for significant contributions to technical progress in the mining and exploration sectors. So, when I was notified that I had received this award, I struggled for a topic that would meld the legal world that I operate in with the engineering driven world of exploration and extraction. The most exciting part of my job has always been the opportunity to absorb the technical details of the cases I work on and, in effect, translate them for a lay audience. Too often, I have found, lawyers, judges, legislators and yes, even regulators who lack a technical background simply give up trying to understand the details of the very conditions or processes that they are trying to describe and simply repeat phrases told to them by their client or by a retained expert.

Jan 1, 2008

By Peter Schmäh, Tobias Engel

The E-Power Pipe technology was originally developed for the trenchless installation of protective pipes and pipelines of 10" to 28" diameter, over long distances of more than 4,000 ft. The twostage process combines elements from Horizontal Directional Drilling (HDD) and microtunnelling technology. A microtunnelling boring machine (MTBM) excavates the borehole using a specially designed, temporary jacking pipe. A Rack & Pinion jacking frame pushes the equipment during the pilot bore and pulls in the prefabricated pipe string in a second step. The slurry microtunnelling machine is equipped with a jet pump, creating the so-called AVNS machine type. A new generation of small hard rock cutting wheels complements this considerable achievement for the tunnelling industry

Dec 1, 2022

By David J. Hatem, K. Bhattarai

Effective risk management in major subsurface projects involves ways to mitigate adverse impacts to final design and construction approaches due to changed subsurface conditions. An Early Contractor Involvement (ECI) collaborated with Observational Method will be an effective contractual tool to address risk developed due to encountering differing site conditions. Observational Method (OM) can further be supported with artificial intelligence (AI) technologies with automated data-driven decision-making features in risk mitigation and implementation of proper design and construction approaches. This paper presents collaborative applications of ECI, OM, machine learning, and risk baselining in risk management and productivity enhancement in tunneling projects.

Jun 23, 2024

By P. W. Finck

Detailed mapping, using a large diameter diamond-drill in conjunction with high resolution reflection seismics, has increased known resources of kaolin clay and glass-grade silica sand from scattered deposits generally < 1 km2 to large areas of Cretaceous valley fill up to 130 m thick. Detailed chemical and physical analysis of drill core is presently underway. Silica sand deposits intersected in this study are up to 99.4 % SiO2 without beneficiation. Light grey to white kaolin clays identified by XRD and DT A have concentrations values (without beneficiation) up to 47.28% SiO2, 37.44% Al2O3, 0.45% Fe2O3, 0.49% K2O, 0.07% Nap, 0.07% CaO and 0.39% MgO.

Jan 1, 1996

By Kotaro Ohga, Kiyoshi Higuchi

In our laboratory, a new detection system using smell detectors was developed to detect the spontaneous combustion of coal and the combustion of other materials used underground. Laboratory experiments were carried out on several kinds of coals, including South African coals, and machine oil, wood and rubber used in belt conveyers. The following results were obtained: 1) Spontaneous combustion of coal can be detected earlier by smell detectors than by conventional CO detection methods. 2) There were no differences in the results using different kinds of coal. 3) Combustion of other materials can also be detected earlier by this system than by conventional detectors for gas and smoke. 4) Use of this detection system enables one to discern the source of the combustion gases, whether it be coal, wood, oil or rubber.

Jan 1, 1995

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By L. Michael Kass

Editor’s note. The following letter was sent to The Washington Post following the coal mining accidents in January that claimed the lives of 16 coal miners. The Sago Mine disaster in West Virginia and tragic deaths of 19 coal miners nationwide have reminded us that mining coal is still a hazardous occupation. The public outcry has already led to the passage of stronger mining regulations in West Virginia. Improved federal regulations will likely follow.

Jan 1, 2006

By D. E. Munson, T. M. Torres, D. A. Blankenship

The Thermal/Structural Interactions (TSI) In Situ Tests are a series of large scale, well instrumented tests that have been constructed at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. As a precursor to the TSI tests, a ventilation drift (Room D) was mined, drilled and instrumented. This room provided the contractor an excellent area to practice controlled construction methods and was a proving ground for construction monitoring and documentation methods. All gages in this first room have been monitored since their initial installation, which has provided a small, but representative, data base. These data also were the first to be available from any TSI area for analysis. This paper discusses the construction activities in Room D and the data generated from the construction and drilling. Deformation of the room is compared briefly to numerical calculations that used a rather simple creep model as a reference. The constitutive model for salt, it appears, must be improved before it can predict the underground deformations.

Jan 1, 1986

By Geoff Whebell, Dianne Coulthard

Sampling studies of high silver (+70%), gold dore led to the development of mine site sampling techniques and superintend­ing for the collection of samples for assay and bullion weights for settlement of shipped material. Data is presented which con­firms the reliability of the procedures against the traditional remelting and sampling at the refinery. The advantages to both mine and refiner are significant and are discussed.

Jan 1, 1998

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011