Search Documents

By Todd Minoski, Matthew McElhinney, Mark Morris, Mark Mazzella, Joseph Bright, Morgan Sears, Craig Compton

To promote the safety and health of U.S. mineworkers, researchers with the National Institute for Occupational Safety and Health (NIOSH) are currently involved in gathering additional field data from the nation’s underground coal mines. The purpose of this field study was to monitor ground movement and changes in pressure during mining where conditions include a thick parting in the coal seam. To accomplish this, three arrays of field instrumentation were installed in the wraparound bleeder of a room-and-pillar panel at the Maple Eagle mine located in southern West Virginia. Borehole pressure cells (BPCs) were used to monitor the change in pressure in pillars located adjacent to the gob. Roof extensometers were installed to measure roof sag at various horizons in the immediate roof, while rib extensometers were installed to measure displacement of the in-seam parting as mining progressed. Additionally, visual observations and manual measurements were taken during subsequent site visits. The repeatability of results, important from a scientific perspective, was accomplished by successfully obtaining field measurements from two nearly identical instrumentation sites. The data collected indicated that the front abutment extent at the edge of the panel was approximately 200 ft, corresponding to a distance of 9– 10 times the square root of the depth. Yielding of the slabbed pillar began when the pillar line was approximately 290 ft outby the instrumentation sites. This was followed by load shedding onto the abutments and the measurement of small amounts of roof sag in the No. 1 entry. Instrumentation data, as presented in this paper, can be used to better understand stress redistribution, pillar performance, and roof/rib displacements. Additionally, this data is suitable for assisting in the calibration of numerical models. Insight gained from applying these models can be used to make better engineering-based judgments for conditions that could potentially be encountered in the future.

Jul 1, 2023

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By Osamu Shoji, Mamoru Kato

In order to continue improving the quality of telecommunication services to meet the expectations of the people and to increase reliability in the case of emergency such as disasters, Nippon Telegraph and Telephone Public Corporation (NTT) is now constructing cable tunnels which connect main urban telephone offices. However, almost all the large cities in Japan are built in river deltas, so that their chief underground features are low strength fluvial deposit and a high ground water level. In this saturated soft ground, the ground surface at an installation site has occasionally subsided through deep excavations for cable tunneling construction. As these settlements have sometimes caused accidents, especially in densely populated large cities, NTT has made much effort to avoid such accidents. These accidents have occured mainly in flexible sheeting due to its inward movement. Therefore, after the investigation into forecast method of sheeting deflection with accuracy, NTT has reserched a system which forecasts ground surface settlements. This paper describes an outline of the ground settlement forecast system and practical example on the site.

Jan 1, 1979

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By T. N. Moore, E. M. De Souza

Because jackleg rock drills are a potential source of hand vibration exposure, they can effectively produce Hand Arm Vibration (HAV) Syndrome in their operators. This will affect operator efficiency and mine productivity. As a result, a significant amount of work has focused on redesigning rock drill handles using new materials to minimize hand-transmitted vibration. In previous work developed by the authors (1991), a detailed study was undertaken to determine the effectiveness of using elastomer covered handles in place of the standard steel design. The results indicated that, for an elastomer-based handle design, the overall acceleration level experienced by the hand can be reduced by as much as a factor of three, relative to the steel handle. It was also shown that this reduction takes place predominantly in the frequency range above 500 Hz. This paper presents an investigation of the long-term effectiveness of an elastomer-cushioned handle under different conditions underground. In this study, sponsored by the Mining Industry Research Organization of Canada (MIROC), a number of cushioned handles were quantitatively and qualitatively tested in five operating mines. The vibration testing program has indicated that the cushioned handle can reduce overall vibration levels by as much as a factor of three. The qualitative assessment program of the cushioned handles by the drill operators has indicated some degree of preference for the cushioned handles over the steel handles, if certain design modifications are performed. This research program indicated that cushioned handles have the potential to become the dominant method with regard to vibration reduction and operator performance.

Jan 1, 1994

By A. J. P. Durham

Two low water flux test covers were placed on acid generating waste rack dumps at the Kidston Gold Mine in Queensland, Australia The climate is semi arid with distinct wet/dry seasons. The present study was initiated to develop a cover system to restrict infiltration. The design of the cover required optimization of water storage and evapotranspiration. Instrumentation was installed on both dumps to measure infiltration, moisture conditions and climatic parameters. Field measurements over the last three years indicate that both covers are performing satisfactorily. Selection of the final cover for closure is described on the basis of these results.

Jan 1, 2000

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health(NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

Jan 1, 2003

By Daniel P. Coughlin, Robert C. Thomas, Christopher S. Romanek, Kristian W. Paul

Two separate constructed treatment wetland (CTW) systems receiving the same metal contaminated, acid sulfate water over different lengths of time and at different rates were evaluated for metal attenuation. Both wetlands are the alkalinity generator portion of a succesive alkalinity producing system (SAPS). Sequential extractions are employed to determine phases of metal removal. Results indicate that Fe, Al, Zn, Ni. and Cu accumulate in the organic substrate over time. Manganese accumulates initially, but is not retained in the system over time.

Jan 1, 2000

By Eric Jackson

The presentation describes the operation and field test results of a seafloor massive sulphide prospecting system. The prospecting system is deployed from a work-class ROV, and it features a new and innovative electromagnetic ocean floor conductivity sensor. It also includes magnetometers, a multibeam sonar, and subsea cameras. The prospecting system has been used in two exploration campaigns - one in the territorial waters of Papua New Guinea (PNG) in 2007 and again in 2008 in both PNG and Tonga waters. The 2007 campaign used the prototype sensor, and the 2008 campaign used a Mark II version. Correlations between drill core samples and EM conductivity results are excellent. New prospecting system data will be used to help plan future core drilling locations. The presentation discusses the principle of operation of the EM conductivity sensor, discusses improvements made in the EM sensor and the overall prospecting system, and shows exploration results. Keywords: seafloor massive sulphide, geophysics, ocean floor, subsea, electromagnetic, conductivity, magnetometer, multibeam, core drilling

Jan 1, 2008

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By R. Krog, S. Schatzel, H. Dougherty

Longwall coal mine operators in the U.S. are required to ventilate multipanel longwall districts, but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs) and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. U.S. coal mining stakeholders have acknowledged their belief that the T-junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the ventilation air stream on active and inactive longwall panels. Testing was performed on multiple longwall panels that included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. Changes in the T-junction ventilation air distribution over the life of a longwall panel, and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements.

Jan 1, 2011

If the communication/tracking system of an underground mine is severely damaged in a large mine accident or explosion, a surface based seismic system could be the only available tool for locating any trapped miners. This paper documents a field test of a seismic system at a room-and-pillar coal mine in Eastern Kentucky. Testing was performed at 6 different depths (450, 575, 750, 1175, 1525 and 1700 ft) above the mine. For each location underground, the miners pounded a ?set? of 5 ?repetitions? on the roof with each repetition being about one second apart. Over the 3 day field test, 63 sets of underground miners? pounding were detected by the seismic system at depths up to 1175 ft and at horizontal offsets up to 890 ft. Also during the testing, the observed signal strength generated by pounding with a crib blocks was seen to average 180% stronger than the observed signal strength generated by pounding with a sledgehammer. Ultimately, this field test was very successful and definitively demonstrated the ability of the seismic system to detect potential trapped miners? pounding up to a depth of 1175 ft.

Feb 23, 2014

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By Todd Grounds, William R. Reed, VASU GANGRADE, Michael Shahan, Garron Ross, Kunal Singh

Roof bolter canopy air curtains (CACs) are gaining acceptance as a respirable dust control device that can provide roof bolter operators with protection from overexposure to respirable coal mine dust. Both lab and field studies on the effectiveness of roof bolter CACs have been published. Field studies have shown the effectiveness to be variable. However, in all previous field studies, none has been conducted when the roof bolting machine operates downwind of the continuous miner (CM)—a scenario for which the CAC was designed to provide respirable dust control. This study, performed by researchers from the National Institute for Occupational Safety and Health (NIOSH), was conducted to test a CAC on a roof bolter machine operating downwind of the CM. The results of testing demonstrated that the roof bolter CAC can effectively provide respirable dust protection for roof bolter operators with dust control efficiencies ranging from 11 to 40%.

Oct 14, 2020

By T. H. Jones

Fall of ground is a leading source of worker injury and fatality indicating a persistent need for ground monitoring technology. The HRTMM is an experimental convergence monitor utilizing a digital camera and custom software to track the position of one or more lasers across the target. Apparent laser movement is proportional to target convergence. The HRTMM was installed in an underground mine near active operations to test its response to the mining environment. This included intense blasting vibration and mine fog. Results and potential of the new monitoring technology will be discussed.

Jan 1, 2008

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By L. L. Oriard

The author describes three case histories of fracture-control blasting demonstrations. This is a technique in which the walls of blast holes are scribed or notched in order to enhance the development of blast_induced fractures, and to control their direction. One demonstration was that of a tunneling application in a rock that was generally competent but strongly foliated, hence strongly anisotropic. P second test was conducted for perimeter blasting of a structural excavation in a massively jointed limestone. A third field test was conducted for tunneling through an old concrete structure. Increased applications are envisioned with new tool modifications being developed at the University of Maryland.

Jan 1, 1981

By L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly. However, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics—namely, size and location—are of great importance in reducing the risk of mine fire injuries. A new, improved fire location algorithm has been developed and integrated into an atmospheric monitoring system (AMS) program by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve the detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.