Search Documents

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By David X. Zhang

This paper describes the results of using shear flocculation and flotation known as aggregative flotation technique for the enrichment of coal-derived char produced from mild gasification process. Aggregative flotation is a separation process which involves the use of suitable aggregating liquid under the action of high shear forces to render hydrophobic surface of coal-derived char particles to aggregate in an aqueous slurry. The fine carbonaceous particles are aggregated into larger floes while the impurities remain hydrophilic. In subsequent flotation process, the char aggregates are then separated from mineral matters by aeration in the flotation cell. The floatability of char aggregates and removal of mineral matters from chars are studied in a lab scale flotation column cell. The effect of various operating parameters on the aggregative flotation responses is presented. Emulsification of aggregating liquid using high intensity agitation and ultrasonic energy provides excellent aggregating liquid dispersion and increases selectivity for char aggregation. In subsequent flotation process, it results in significantly increasing the flotation rate of char aggregates. The microscopic examinations of bubble attachment to coal-derived char particles under various aggregating liquid dispersion levels were conducted by induction time measurement. The distributions of hydrophobicity of char particles and char aggregates prepared under various aggregating liquid dispersion techniques were measured by film flotation. The char particles prepared under high intensity emulsification attach at significantly faster rates to air bubble and with lower mean critical wetting surface tension than that of char with direct aggregating liquid addition. An interrelationship of increasing in flotation rate/combustible recovery with decreasing in induction time, mean critical wetting surface tension and dispersion of hydrophobicity on the char particles and char aggregates were obtained.

Jan 1, 1992

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov, D. V. Magazanik

Based on theoretical and experimental researches of phosphate and carbonate minerals flotation in the presence of soluable glass at various pH values and sodium silicate concentrations, it has been established that the presence of soluble glass in solution leads to formation of silicate compounds on the surface of phosphate and carbonate minerals causing change in their floatability for the worse. The harmful influence of soluable salts is done by tying of collector as metallic soaps, forming precipitates on the surface of minerals to be floated and causing their depression of flotation, and breaching of the froth etc. Depressing action of slimes and products of interaction with collector depends on the ratio of values and signs of potentials of the mineral surfaces. The possibility of phosphate and gangue minerals separation can be evaluated by comparing the minimum-necessary concentrations of collector required for their flotation.

Jan 1, 2002

By Joshua Cole, Joshua Sovechles, Christian Cardoso, Guillermo Bermudez, Martta Hirsi, Joshua Dettamanti, Rabia Abbasi

The implementation of technological advancements in flotation is key to optimize performance in mining operations. Consequently, flotation cell’s performance is highly dependent on the effectiveness of the mixing mechanism. A more efficient flotation mixing mechanism is likely to improve metallurgical performance and optimize energy consumption, which is the motivation for Metso’s journey to develop the latest iteration of FloatForce®. Looking to test the new design at plant scale, Metso approached the Kennecott Copperton concentrator, which is continuously looking for different venues to improve metallurgical performance. In this context, a test campaign was conducted to implement this new flotation mixing mechanism in their rougher circuit during 2024. The industrial trial consisted of several sampling campaigns assessing different operational parameters for comparison purposes around a 300m3 flotation cell. The effect of the new flotation mixing mechanism on the cell’s power draw was also studied. The results of this trial at Kennecott are presented in this paper. Overall new flotation mixing mechanism, FloatForce+ was seen to perform as well as the original FloatForce.

Feb 1, 2025

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By S. K. Kawatra, H. Haselhuhn

"In many mineral processing applications it is necessary to know the isoelectric points of the various minerals in the ore to properly perform flotation and other mineral separations. However, current zeta potential analysis technology used to determine the isoelectric point of a particle suspension cannot deliver the isoelectric point of each individual mineral, just an average of the mineral system. Traditionally, individual isoelectric points have been gathered by testing pure, synthetic minerals. These values can vary widely depending on the mineral synthesis procedure and the water quality used during the isoelectric point analysis. A more robust approach for determining the actual isoelectric point of a particular mineral in a mixture of minerals is needed. This paper details a method for determining the isoelectric point of an iron oxide mineral in a siliceous iron ore. The method uses a laser scattering particle size analyzer and a pH electrode to determine the pH at which the liberated mineral particles begin to flocculate as pH is decreased. The pH at which the average particle size rises dramatically is the isoelectric point of the mineral with the highest isoelectric point in the ore. This measurement technique was used on natural hematite, goethite and siderite ores as well as a synthetic mixture of pure silica and pure hematite. The results for synthetic hematite mixtures were comparable to literature values.IntroductionRecently there has been an increased interest in the processing of low-grade iron ores (Bolen, 2014; Carlson and Kawatra, 2008, 2011, 2013; Halt et al., 2014; Halt and Kawatra, 2014; Haselhuhn 2012, 2013; Haselhuhn et al., 2012a, 2012b; Kawatra and Halt, 2011; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). The zeta potential of iron ore minerals is a very important and often overlooked aspect of iron ore mineral processing. Zeta potential is the charge at the shear plane of a surface in an aqueous environment (Carlson and Kawatra, 2013). Many ores consist of a variety of minerals differing in zeta potential. This property of a particle surface in water is responsible for either keeping the particles dispersed from each other or flocculated to each other. This is important during many operations such as flotation, desliming and thickening. Zeta potential is primarily a function of the pH of the water and the mineralogy of the particles, though certain ions within the water can also have a significant impact (Haselhuhn, 2012). Consider the following situation: silica (SiO2) particles and hematite (Fe2O3) particles are suspended in an aqueous solution. These two types of minerals have drastically different zeta potentials throughout the pH spectrum (Esumi et al., 1988). In alkaline conditions, both types of particles exhibit negative zeta potentials and will tend to disperse from each other. In acidic conditions (between pH of 3 and 6), silica has a negative zeta potential while hematite has a positive zeta potential, so these surfaces will tend to be attractive to each other and the particles will flocculate and settle. This phenomenon is visually described in Fig. 1. The pH at which the two minerals begin to attract to each other, or destabilize, is near hematite’s isoelectric point. The isoelectric point is defined as the pH at which the surface has a net zero zeta potential (Carlson and Kawatra, 2013)."

Jan 1, 2015

By J. E. Gebhardt, L. Piga, G. Schena

The possibility of beneficiating a low-grade alunite ore from the Tuscany region of Italy was examined. Flocculation and flotation techniques were investigated to separate alunite and kaolinite from the ore, which also contained feldspar and quartz. Flotation was performed at pH 6.5 with oleic acid as collector and sodium silicate as dispersant. A concentrate containing 12% alunite with a recovery of about 65% and a concentrate containing 28% alunite with a recovery of 84% were achieved from the -38-µm feed samples containing 5.0% and 12.9% alunite, respectively. Poor recovery of alunite was achieved by flocculation methods.

Jan 1, 1999

By S. Behl, S. Mathur

It was previously reported that dolomite samples from different locations showed varying flocculation behavior with poly(ethylene oxide) (PEO). In this study, a Florida dolomite sample was examined, and it was determined that palygorskite associated with dolomite was responsible for its flocculation with PEO. A detailed characterization of dolomite samples from different locations was made by electrokinetic, XRD and FT-IR analyses, and the relevance of these characteristics to flocculation with PEO is discussed.

Jan 1, 1996

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By H. Suharyono, R. Hogg

A laboratory investigation was performed on flocculation following the addition of polymer to slurries flowing through pipes and in-line (static) mixers. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points. Flocculation performance was measured by the settling rate and the supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests (both batch and continuous) conducted in stirred tanks.

Jan 1, 1997

By H. Suharyono

A laboratory investigation of flocculation following polymer addition during slurry flow through pipes and in-line (static) mixers is described. Results are presented showing the effects of flow velocity, pipe length, in-line mixer elements and the use of multiple addition points on flocculation performance as measured by settling rate and supernatant turbidity. The effects of agitation and mixing time are shown to be generally consistent with the results of equivalent tests, both batch and continuous, conducted in stirred tanks.

Jan 1, 1995

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By R. W. Smith, S. A. Davis, A. M. Raichur, M. Misra

The flocculation of coal is typically accomplished by the addition of commercially available polymeric flocculants. Recently it was shown that biopolymers derived from microorganisms can also be used. The biopolymers flocculate coal efficiently and make the coal more hydrophobic. This increase in hydrophobicity can be utilized to separate coal flocs and can be used for reducing the moisture content of the flocculated coal. In this regard, flocculation and settling tests using biopolymers and synthetic flocculants were performed on fine coal. The experimental results are discussed and a transport model is presented for the time-dependent settling of fine coal.

Jan 1, 1998

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By Eva K. Fernandez, Paul Y. Louie, Derek S. Adams, Renée L. Fippin

The Folsom Area Stormwater Improvement Project is part of SFPUC’s flood resilience efforts under the Sewer System Improvement Program. This 4,000-foot-long, 12-footinside- diameter tunnel will help reduce the risk of flooding in San Francisco’s low-lying Inner Mission neighborhood. The project is in a high seismic hazard zone and extends through a complex geologic corridor that includes full-face soft, compressible Bay Mud, Colma Sands, and full-face rock with several stretches of mixed-face conditions. Additional challenges include removal of 99 piles beneath an existing box sewer, tunneling under commuter rail tracks, and an underground tie-in. This paper examines these challenges and how they are being addressed.

Jun 13, 2023

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion. In several cases, breaches occurred between the gravel pit and the river. Initial evaluation of several sites that experienced these breaches showed that impacts to the river system were complex and varied significantly from site to site. The impacts to the adjacent river system may be viewed as positive and negative. Several flood-plain-mining sites in Oregon located in areas of historic river flow reverted to active riverbeds. In many cases, state and federal fisheries biologists and university researchers saw the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries —Mined Land Reclamation Program (DOGAMI-MLR) is studying the effects to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound flood-plain decisions regarding mining.

Jan 1, 1999

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999