Search Documents

By E. F. Schnitzer, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Pramod C. Thakur

Floor gas emissions on wide longwall faces are common occurrences in the Northern and Central Appalachian basins. It creates unsafe working conditions on the face and results in very costly production delays. This paper discusses various methods of mitigating the floor gas emissions including hydrofracing of underlying strata, use of cross-measure boreholes and specifically completed gob wells.

Jan 1, 2005

By K. K. Haramy, J. McDonnel

INTRODUCTION Primarily because of mining at greater depth, an increasing number of coal mines in the United States experience floor heave problems. In many instances, the floor heaves at a slow rate without causing health and safety related problems; only additional roadway maintenance and coal handling equipment are required. However, when rapid, massive heaving occurs, the safety of mine personnel in the vicinity is jeopardized. Extensive floor heave causes a redistribution of stress around the mine opening and can cause additional ground control problems. This paper presents an analysis of rapid floor heave in a deep western coal mine. The analysis is based on field measurements, laboratory data, and beam design theory. Factors affecting floor heave, such as mining-induced stress, mine opening size, entry orientation, mine geology, rock physical properties, and gas pressure, are considered. Examination of floor heave in the mine indicates that heaving is primarily caused by deformation of a soft floor member that is subjected to high mining-induced stress. Theoretical analysis of in situ floor stresses resulting from overburden loading indicates that floor failure will occur. The analysis is confirmed by visual observations of floor heave in the mine. Recommendations for mine layout and opening design to control rapid, massive floor heave under these conditions are also presented. MINE-FLOOR-FOUNDATION THEORY The floor stratum in a coal mine acts as a foundation to support coal pillars and artificial supports, thereby providing support to the mine roof. The overburden load, transferred through pillars and other supports, applies tremendous stress to the floor. Soil mechanics theories provide solutions for foundation design problems that apply to the mine floor. Based on foundation theory, vertical load on pillars causes high shear stress zones in the floor. If the floor is relatively weak, it may fail and dislocate upward into the mine opening. Strong roof strata that do not readily fail transmit most of the overburden load through pillars to the floor. Heaving may result, depending on the thickness and physical properties of the floor

Jan 1, 1986

By Richard F. McFarlin

INTRODUCTION Phosphate, one of the three major elements essential for all living plants and animals, has been mined in Florida for over a hundred years. Comprising roughly 80% of the U.S. total and 25% of the world's supply, the bulk of the 35 to 40 million annual ton output is converted to chemical fertilizers. With the exception of one mine in north Florida near the Georgia state line, today's mining activities are centered in the middle of the peninsula just east/southeast of Tampa in Polk, Hillsborough and Hardee counties. These "bone valley" deposits extend into Manatee and DeSoto counties, but there is little active mining there as yet. Because strip mining is, perhaps, the ultimate environmental insult and because Florida has a proactive environmental community, it is not surprising that the mining of phosphate rock has become increasingly controversial. This paper describes how phosphate rock is currently mined, the environmental problems presented by mining and processing the rock, and some mitigating technologies being employed to answer such problems. THE PHOSPHATE DEPOSIT AND ITS EXTRACTION Florida's phosphate deposits containing the calcium phosphate mineral, carbonate-fluorapatite, are between ten and fifteen million years old. The typical "bone valley" matrix is 15 feet thick and lies under 20 to 30 feet of overburden.(Fig. 1) Both the sandy overburden and matrix are unconsolidated and can be removed with standard 45 to 65 cubic yard, walking electric draglines. After removing the overburden, which is windrowed nearby, the dragline operator casts the matrix into a "slurry" pit where it is broken up by high pressure water monitors. Pit pumps (with boosters where necessary) transport the matrix slurry through 16 to 20 inch pipelines to a washer where the three components of the matrix (sand, clay and apatite) are separated. The phosphates contained in central Florida matrix are approximately half pebble/half flotation feed, through the pebble ratio decreases as the industry mines southward. Again, the matrix is roughly equally divided among sand, clays and apatite. The phosphatic clays, 75% of which are less than one micron in size, leave the washer as a 3 to 5% colloidal suspension. The impoundment of these waste clays is one of the environmental challenges to be discussed later. The sand (silica) is separated from the similarly sized phosphate particles by a double float process (fatty acid followed by a reverse mine or cleaner float), and the sand tailings are then pumped to disposal or reclamation sites. The apatite flotation product is combined with the screened phosphate pebbles and stacked to dewater before shipping.

Jan 1, 1992

By Bruce Congleton

One year ago this month, we in Central Florida witnessed the beginning of a most exciting and glamorous attraction. After three years of construction and anticipation, Walt Disney World opened its gates near Orlando and during its first year of operation received a flood of over 10 million visitors---half of all who came to Florida last year! The side effects of this newest addition to Florida have been phenomenal. Traffic on heavy days has been backed up for 30 miles from the amusement park along a major interstate highway. Hotels and motels have been jammed packed for months, and reservations are still difficult to make. Gasoline stations, restaurants and souvenir shops are doing a booming business. Everywhere you look as you ride the highways of Central Florida you see the signs of growth. New hotels spring up almost overnight. Golf courses galore. New housing projects and apartments sprawl where orange groves used to be. New roads criss-cross areas which were once deserted. There seems to be no end to the steady influx of tourists and new residents to the Sunshine State. And it's mainly because that we are the Sunshine State that they come. Air and water pollution is and has been at a minimum in Florida. Pollution and emissions are fighting words among some groups dedicated to preserving the bountiful environment we share in Florida. Little wonder then that some of these people display concern when they learn that just 50 miles from the entrance to the Magic Kingdom of Disney, phosphate draglines strip away thousands of acres of land each year to extract one of our nation's most precious

Jan 1, 1972

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By Weibai Hu

Four methods to assess the relative flotability of fine coal have been tested: flotation with frother only, flotation with frother and collector, salt flotation, and timed-release analysis. A practical and simple criterion which combines the separation efficiency (capacity factor and kinetic rate constant (intensity factor) has been suggested. Five coal samples are chosen and tested. Based on test results, it is concluded that the flotability test with collector and frother is closer to practice, and, according to the suggested flotability criterion, coal fines can be classified into four categories of relative flotability: very easy, easy, moderate, and difficult.

Jan 1, 1987

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By Michael E. Kelahan, Glenn A. Gruber

A review of recent phosphate beneficiation developments shows that Flotaire cells, ranging from 0.20 m to 2.44 m in diameter, have been examined in pilot scale and commercial plants. Applications of the column cells have included sized feed fractions using anionic and cationic reagent systems. In plants where the Flotaire was installed as a test unit or as an optional circuit, its use has been largely discontinued. On the other hand, when management committed to installing the Flotaire as an integral part of the flowsheet, the performance expectations were met or exceeded.

Jan 1, 1988

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,' the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill's Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

By C. I. Basilio

The adsorption of O-isopropyl-N-ethylthionocarbamate (IPETC) and O-isobutyl-N-ethoxycarbonylthionocarbamate (IBECTC) on chalcocite, chalcopyrite and pyrite has been studied using UV and in-situ FTIR~ATR spectroscopy. Thionocarbamates were found -to adsorb strongly on chalcocite at pH 4-10, but consider-ably less on chalcopyrite and pyrite. The FTIR spectra show that the surface species of thiono-carbamates are bonded to metal atoms on the mineral surfaces. However, at high concentrations, IBECTC also forms physically-adsorbed species. Adsorption of these thionocarbamates cannot remove or prevent the formation of sulfoxy oxidation products on pyrite, unlike the case with the xanthate-pyrite system. This finding may account for the observed flotation selectivity of these reagents against pyrite. The spectroscopic information is compared with flotation test results.

Jan 1, 1988

By S. Chander

A series of nonionic and anionic surfactants were tested to enhance the flotation response of a low rank coal. An ethoxylated octyl phenol and several polypropylene polyethylene block copolymers were tested as nonionic surfactants. The anionic surfactant was a dioctyl sulfosuccinate. All the surfactants employed improved the yield significantly but the influence on grade was complex. Separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents tested, a correlation between emulsifying power of the surfactant and flotation was observed. An increase in the number of droplets produced in surfactant containing systems was considered to be the main reason for increase in the yield. Since it increased the number of collisions between dodecane droplets and coal particles. When a surfactant was introduced into the flotation pulp prior to addition of dodecane, it decreased the benefits of the surfactant significantly. The decrease was attributed to an increase in the wettability of coal and a decrease in the surfactant available for emulsification. When a suitable surfactant was added as a solution dissolved in the oily collector, a considerable increase in yield was observed.

Jan 1, 1993

By H. Polat, B. Mohal, S. Chander

Several nonionic surfactants and one anionic surfactant were tested to enhance the flotation response of a low-rank coal. The nonionic surfactants included an ethoxylated octylphenol and several polypropylene-polyethylene block copolymers, and the anionic surfactant was a dioctyl sulfosuccinate. All of the surfactants improved the yield significantly, but the influence on grade was complex. To elucidate the mechanisms involved, separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents, a correlation between the emulsifying power of the surfactant and the flotation response was observed. An increase in the number of droplets produced was considered to he the main reason for increases in the yield. However, a small amount of surfactant adsorption on coal is essential to promote adhesion of oil droplets. When the surfactant was introduced into the flotation pulp prior to addition of dodecane, the benefits of the surfactant decreased significantly. The decrease was attributed to both a decrease in hydrophobicity of coal through increased surfactant adsorption and a decrease in the surfactant available for emulsification. When a surfactant dispersed in oil was used, the transfer of surfactant to the aqueous phase was minimal, and a considerable increase in yield was observed.

Jan 1, 1995

By M. Li, J. D. Miller

Existing process technologies for the production of soda ash from trona involves dissolution in hot brine, sedimentation and filtration for the removal of impurities, and subsequent crystallization for the recovery of soda ash. In this regard, mining and operating costs, particularly energy costs, are higher than desired. A preferred processing strategy might be to remove gangue mineral contaminants from the plant feed prior to dissolution in hot brine. Such a preprocessing strategy at ambient temperature and pressure has been limited by the lack of satisfactory process technology. Now based on recent results from laboratory research at the University of Utah it seems that the run-of-mine trona ore can be treated at ambient temperature and pressure using a special flotation procedure to separate the gangue minerals and make a trona concentrate with a purity of almost 99% trona at a recovery of more than 97%. The concept of such a new processing strategy is discussed with respect to current plant practice.

Jan 1, 2002

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987