Search Documents

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Faruk Oksuz, Phillip L. Covell, Martin Doll

A series of difficult ground conditions causing high groundwater inflows and hazardous gas intrusion abruptly halted the construction of a 6.4-meter (21-foot) finished diameter and 1,890 meters (6,200 feet) long tunnel planned to serve as a 4-millioncubic meters (1-billion gallon) per day capacity river outfall for treated wastewater. Some 808-meters (2,650-feet) section of the constructed tunnel, TBM, and all other tunneling equipment were completely flooded with hydrogen sulfide laden artesian groundwater. The subsequent pumping and tunnel recovery efforts were unsuccessful and the tunnel was abandoned. In the end, the construction contract was terminated and options to redesign and reconstruct the project were re-evaluated to maximize the use of already constructed tunnel facilities such as the construction access and inter-mediate shafts and six outfall diffuser shafts in the river.

Jan 1, 2007

By R. F. Hüttl

The restoration of surface mining landscapes requires the (re)creation of ecosystems. In Lusatia (eastern Germany), large-scale open-cast lignite mining operations generated spoil dumps widely consisting of acidified, phytotoxic substrates. Amelioration and rehabilitation measures have been developed and applied to these substrates since the 1950s. However, it is still not clear whether these approaches are sustainable. This paper reports on collaborative research work into the ecological potential of forest ecosystem development on typical minesites in the Lusatian lignite district. At first sight, pine stands on minesites along a chronosequence comprising about 35 years did not show differences when compared with stands on non-mined sites of the general region. Furthermore, with some modification, conceptual models for flora and fauna succession in forest stands on non-mined sites seem to be applicable, at least for the early stages of forest ecosystem development. For example, soil organism abundance and activity at minesites had already reached levels typical of non-mined sites after about 20-30 years. In contrast, mine soils are very different from non-mined soils of the test region. Chemically, mine soil development is dominated by processes originating from pyrite oxidation. Geogenic, i.e. lignitic, soil organic carbon was shown to substitute for some functions of pedogenic soil organic matter. Rooting was hampered but not completely impeded in strongly acidified soil compartments. Roots and mycorrhizae are apparently able to make use of the characteristic heterogeneity of young mine soils. Considering these recent results and the knowledge accumulated during more than 30 years of research on minesite rehabilitation internationally, it can be stated that minesite restoration might be used as an ideal case study for forest ecosystem development starting at "point zero" on "terra nova".

Jan 1, 2002

By Fiona Woody

Lime and calcium products are essential building blocks to the modern world, used to purify drinking water, preserve foods, control pollution, improve crop yields, stabilize soil, pave roads and support the production of steel, cement, glass and many other industrial processes. While lime is essential to society, it also has a sizable carbon footprint. Approximately 30 percent of the scope 1 greenhouse-gas emissions generated during lime production are related to fuel combustion, while the remaining 70 percent are created by the unavoidable chemical reactions during calcination.

Feb 1, 2026

By M. Mustafa Kahraman, Sean Dessureault, W. Pratt Rogers

Most contemporary mines have considerable amounts of data. Structured and unstructured large data sets are colloquially named big data. Much of the data in mining operations come from a variety of systems, each with different databases and reporting environments. Standard technology deployments create a Bsilo-ification^ of data leading to poor system benefit. Through modern server monitoring and systematic approach, data utilization and value can quantifiably be measured. The Data Utilization and Value Index (DUVI) can quantify business intelligence best practices and user interaction. This study seeks to provide a data management tool to measure data utilization across the process of converting data into action.

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By Numan Elmas

This paper presents detailed information on the genesis, formation, and industrial utilization of Yaylacik magnesites. Tectonically, the study area is located within the Tavsanli Zone, immediately south of the Izmir-Ankara suture in western Turkey. The geologic setting mainly comprises ophiolitic melangks basics, and ultrabasics associated with very rich magnesite deposits and lacustrine sediments. The ophiolitic unit tectonically overlies the schists and carbonate rocks. The presence of glaucophane and lawsonite indicates a low-temperature/high-pressure metamorphism. The ultra- basic rocks, which exhibit cumulate composition, have been mostly serpentinised and represent the oceanic floor of the Yaylacik ophiolite. Basic intrusives consist of dolerite and diabase, and they show the characteristics of within-plate dolerites. The magnesite occurrences are commonly observed in block, stockwork, lens, and vein forms and were deposited within the serpentinites. In most magnesite samples, secondary quartz/chalcedony formations are observed as fracture fillings due to the highly effective tectonic movements. Field surveys and microscope studies reveal that magnesites had been formed by the metasomatic alteration of serpentinites. Chemical analyses show that, although MgO content of the magnesites varies from 43.41% to 50.48%, Fe203 and CaO are lower than 1%. Silica contents are as high as 5.52% in a few samples. Although Yaylacik magnesites are not suitable for making basic refractory bricks, they are widely used as caustic-calcined magnesite in a variety of applications, including animal food, artificial fertilizer, chemical (acid neutralizer), medical and pharmaceutical, and water treatment.

Jan 1, 1999

By Edward L. Mooney

In the, West, walking draglines often offer the least cost method of uncovering coal for surface mines. However, with each of these machines costing millions of dollars, a good deal of analysis can be justified by the potenial savings or, conversely, costs associated with the choice of a machine. This has resulted in the recent development of a number of computerized models for dragline selection and pit design. One of the earliest reported models for this purpose was developed by Dunlap and Jacobs (1). Later, Rumfeldt described the computer approach to sizing stripping draglines given the required production rate and mine site parameters (2). This basic approach is probably still the most widely used with models for more complicated mining methods reported by Stefanko, Tomica, Finch, as well as others (3,4,5). furthermore, detailed simulation models useful in this regard have been developed by McDonnell Douglas and Fluor, Utah (6,7)

Jan 1, 1982

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By P. A. K. Wilkinson

This paper is concerned with the development of an in situ recovery of boric acid from a deep-seated colemanite deposit in California. The deposit contains 147 million tons of borate ore containing 6.4% boron oxide (B203). It is the largest undeveloped colemanite deposit in the United States and because of its unique occurrence and grade, in situ extraction appears to be the most economic viable process. The paper covers the geological, mineralogical, hydrological, well-field development, and extraction considerations leading to the initial pilot plant and subsequent demonstration plant phases of the project. Market potential aspects and preliminary economics of the project are also covered.

Jan 1, 1987

By G. J. Hartman

A presentation of this project was given previously at the SHE Annual Meeting, Denver Colorado February 23-27, 1987. The project concerns the development of in situ recovery of borate products from a deep-seated colemanite deposit in California. The deposit contains some 147 million tons of borate ore containing 6.4% boron oxide (B2O3). This paper involves the numerous changes in the process that has taken place since that first presentation. This paper further explains the reasons for these changes which are primarily environmentally based and secondarily capital requirements related.

Jan 1, 1994

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

Caterpillar and Fortescue Metals Group have moved forward with the delivery, installation and support of a complete Cat MineStar System at Fortescue?s Solomon iron ore mine in the Pilbara region of Western Australia. The complete technology suite was implemented for the first phase of Solomon, the 20 Mt/a (22 million stpy) Firetail manned mine, in October 2012. As part of an autonomous mining solution for phase two, the 40-Mt/a (44-million stpy) Kings Mine, eight Command for hauling Cat 793F CMD trucks were commissioned and commenced operations in the second quarter of 2013. The mine plan calls for a progressive ramp up to 45 autonomous trucks during the next several years. In addition, other Cat MineStar System capability sets, Fleet, Terrain, Detect and Health, are being used across the mobile equipment fleet, including support equipment and light vehicles. Working closely with Fortescue and its mining contractor, Leighton Contractors, Caterpillar and the Cat dealer in Western Australia, WesTrac, are providing a full solution for managing, operating and supporting Cat MineStar System and Command for hauling. The greenfield Solomon Mine has brought together the skilled team from Caterpillar, Fortescue, Leighton Contractors and WesTrac to deliver an efficient, cost effective autonomous mining solution.

Nov 1, 2013

By Timothy J. Matthews, Timothy J. Batchler, Daniel J. McElhinney

The National Institute for Occupational Safety and Health’s (NIOSH) Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division was commissioned for operation in 1981. The MRS was originally designed for longwall shield research and was the only hydraulic press in the world with the capability to apply biaxial loads to these large structures. The results of this forty-year research program have contributed to improved performance and increased knowledge of longwall shields, mobile roof supports and hydraulic cylinders in the mining industry. Also, considerable research and development have been conducted to develop standing support technologies for the mining industry. The Support Technology Optimization Program (STOP) was developed to evaluate how these various technologies can impact and improve both ground control conditions and mine safety. Additional MRS research has included the performance of ventilation stopping walls including the development of a new testing protocol to evaluate the transverse loading capabilities under arching load conditions and evaluating the performance characteristics of welded wire screen as used in underground mine roof surface control. The NIOSH Mine Roof Simulator has been a reliable and valuable tool for the past forty years for the evaluation of safety structures used in mining, and this research has contributed significantly to the advancement toward safer mines. This paper will summarize those research results and provide a glimpse of planned future activities.

By Charles Schmidt

Phalabonva (Figure 1) is situated in the northern province of South Africa adjacent to Kruger National Park, about 500 km from Johannesburg. The nearest South African port to Phalaborwa is Richards Bay about 700 km distant by rail.

Jan 1, 1999

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By Wilbur J. Morin

Construction of Flaming Gorge Dam in northeastern Utah necessitated the construction of a new state highway, Utah-260, to provide access to the dam and the town of Dutch John. A 550-foot arch structure was designed to span Cart Creek, about one mile southwest of the dam. The rock exposed at the site is highly fractured quartzitic sandstone with interbedded shale of the Precambrian Uinta Mountain Group. Eight exploratory holes were drilled, four in each abutment area, to determine rock types, the extent of fracturing at depth and rock strength. Drill cores in the west abutment revealed blocks of quartzitic sandstone loosened by the weathering and partial removal of underlying shale beds. The rock in the east abutment area was found to be highly fractured to depths of 70 feet and as far east as 50 feet from the footing locations. Selected core sections were tested for unconfined compressive strength but the values were not considered-representative of the in-situ fractured rock. To prevent movement along or, perpendicular to open fractures, four drilled-in columns were provided at the base of each footing. These extended 50, feet beyond the base of the footing, along the bearing and inclination of the thrust reaction.

Jan 1, 1963

By Ronald E. Yarbrough, Theodore L. Triplett, Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from a high-extraction retreat room-and-pillar operation in southern Illinois. The objective of this monitoring program is to study the inter- action between the ground surface and a structure during a subsidence event. Data from such a study should enhance the understanding of the mechanisms that produce structural damage and aid in the design of structures that resist such damage. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tiltmeter to detect and follow the tilt of the foundations caused by the mining subsidence sequence is demonstrated. Using data from this tiltmeter, the development of curvature in the foundations as they conformed to the displaced ground surface is shown. This curvature is rep- resented by differences in tilt at various points on the foundations, indicating a change in tilt over a horizontal distance. Also, even though subsidence damage has not been fully analyzed, preliminary observations of the cracks that formed in the foundations are reported. These cracks resulted in the separation of one footing into distinct pieces; therefore, their effect on the tilt readings is cited.

Jan 1, 1986