Search Documents

By Terry Mudder

Long-term anaerobic biochemical treatment for draindown of residual solutions is a cost-effective way to close a heap-leach pad. This article presents a laboratory evaluation of anaerobic biochemical treatment of cyanide heap-leach pad solutions. The traditional approach to heap-leach pad closure is to rinse the pads with multiple pore volumes of fresh or recycled treated water. The effluent from an initial rinse is often treated and recirculated until the solutions passed through the heap meet the appropriate numeric and narrative water quality standards. Column rinsing tests are completed during project planning to determine the number of pore volumes of fresh or recycled treated water required to rinse the pad to meet long-term closure requirements. A traditional closure plan generally includes provisions to sample the rinse effluent and rinsed solids (the Meteoric Water Mobility, Procedure or USEPA 1312) to verify that chemical requirements are being met.

Jan 1, 1995

By Landy A. Stinnett

Coal mines in the United States are the most productive in the world in terms of efficient labor employment. This is because of an abundance of workable coal beds, large infusions of capital, improved management practices and continuing competitive pressures. The standard unit of measurement for labor productivity is expressed as tons/manshift, although for underground mines, operators often refer to tons per machineshift. Articles written concerning labor productivity generally focus on measurement techniques, safety considerations, application of technology and training. This article will illustrate by example the impact of labor efficiency (or inefficiency) on the ultimate selling price of coal, f.o.b. mine site. During the past several years, the coal industry has seen significant improvement in labor use. Figure 1 shows the trends in productivity for all active mines in the United States from 1985 through 1994. Productivity in 1985 was 20.1 t/manshift (22.1 st/ manshift). This factor has increased almost linearly throughout that period to 37.5 t/manshift (41.2 st/manshift). This is a 7.2% annual compound growth rate.

Jan 1, 1995

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

The National Institute for Occupational Safety and Health conducted laboratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter?s dust collection system. The laboratory tests evaluated the bag?s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector?s exhaust were also measured in each condition during laboratory testing. Laboratory results show that nearly 100 percent of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector?s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

Jan 1, 2008

By L. Wade, D. R. Pearce

A detailed account is given of the spectral ratio laboratory method for the determination of seismic velocity and attenuation through rock cores under simulated in-situ stress conditions. An account of a computer program called AUTOQ is described for automatic processing of a complete set of laboratory results. Some of these results are shown and discussion is directed to- wards the suitability of in-situ velocity or attenuation measurements in determining rockmass condition or stress regime.

Jan 1, 1996

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By V. B. Achanti, A. W. Khair

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be: bit spacing, bit geometry, depth of cut and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Tree bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 900. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Restorable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Feb 24, 1997

By V. B. Achanti, A. W. Khair

Introduction Laboratory studies were carried out at West Virginia University to investigate the rock-fragmentation mechanism of continuous miners using an automated rotary cutting simulator. The primary factors influencing the fragmentation process were found to be bit spacing, bit geometry, depth of cut and cutting-drum rotational speed. This paper presents a discussion of the effects of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation. The removal of rock ridges/walls between adjacent grooves is analyzed with three hits mounted simultaneously on the cutting head, while the bit tip angle was varied from 600 to 900. Bit spacing was varied from 25.4 to 50.8 mm (1 to 2 in.) while the cutting process was assessed for varying cutting depths. Respirable dusts generated during the course of the experiments were analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism of continuous miners in terms of energy consumption and dust generation. A review of the literature revealed that a considerable amount of research has been carried out on rockcutting processes. Many authors agree that the mechanical cutting efficiencies of mining machines (e.g., continuous miners, shearers and road headers) are affected by a host of parameters. Some of these parameters are machine controlled, some are operator controlled, while others are uncontrollable. Efforts were focused on understanding the influence of parameters such as bit spacing, cutting depth, attack angle, bit type, drum speed, bit geometry (i.e., tip size, shape and tip angle) and rock type on the cutting process efficiency in terms of specific energy consumption and respirable dust generation (Strehig?? et al., 1975, Hanson et al., 1979, Khair et al., 1989). Roepke et al. (1976) in an attempt to study the dust and energy generated during coal cutting using point attack bits found that the dust and the specific energy consumed both decrease as the depth of cut increases. The four fundamental stages of dust generation luring rock fragmentation are identified by Zipf and Bieniawski (1989). Coal breakage by various types of wedges was assessed by Evans and Pomeroy (1966) in an extensive experimental study on British coals. Yet the industry today requires further attention and guidance to optimize the energy consumption and dust generation during the rockbreakage process. This paper attempts to give a better understanding of the influence of some of the parameters listed above and focuses on further improvement in the rock-cutting process. The specific energy consumed for different types of bits used and the respirable dust generated are analyzed in the context of the variation of a few other parameters. Laboratory investigation The experiments were performed in the Rock Mechanics Laboratories located at West Virginia University. A rock-cutting simulator designed and fabricated by Khair (1984) was utilized for this purpose. The details of this machine are available in the literature (see Khair 1984). For this study, a series of preliminary experiments was carried out to determine the optimum cutting frame advance speed. This was intended to facilitate a maximum cut depth of 31.75 mm (1.25 in.) at an advance rate of 0.525 mm/s (0.0207 ips) for all types of bits being used and various bit spacings being considered. To look into the cutting-process efficiency of a continuous miner in the laboratory, several parameters of influence are being considered. Besides the bit-geometry parameters, machine- and operator-controlled parameters, such as spacing of bits on the cutting head, the cutting head rotational speed and the total cutting depth during an experiment, are varied. At the time this paper was written, only part of the completed experiments were ana¬lyzed, and a number of experiments were still being carried out following an orthogonal fractional factorial experimental plan to assess the effect of all of the above¬mentioned parameters on the cutting efficiency in terms of energy consumption and dust generation. Three different types of tip angles, namely, 60°, 75° and 90°, and two different tip sizes, namely, diameters of 7.94 and 24.61 mm (0.313 and 0.969 in.), were used. At

Jan 1, 1999

By K. J. Shoop, S. J. Ripke, T. C. Rao, T. C. Eisele

This study investigated the use of a 7.6-cm inside diameter, 344.2-cm-tall horizontally baffled column to reduce the ash content of a low-sulfur bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage and feed quality. The tests were also carried out to compare the columns performance to a conventional column installation in an operating plant. In this paper, the results of this investigation are reviewed and discussed.

Jan 1, 1999

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997

By S. K. Kawatra, T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of back mixing of tailings into the froth zone, and the recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically constructed very tall (30 to 40 ft) to limit the effects of back mixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug flow. In this work, horizontal baffles were shown to improve the performance of a 6 -ft laboratory-scale flotation column treating a poorly floatable coal. Tests with variations in the baffle positions showed that baffles are needed both above and below the feed inlet to achieve the greatest benefit. Tracer tests with a fluorescent dye in water showed that baffles reduce the amount of feed water entrained in the froth at any given coal recovery.

Jan 1, 1996

By T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of backmixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically made very tall, on the order of 30-40 feet, in order to limit the effects of backmixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug-flow. In this work, horizontal baffles were shown to improve the performance of a 6-foot tall laboratory-scale flotation column treating a difficult-to-clean, heavily oxidized coal. Tests with variation in the position of the baffles showed that for the greatest benefit, baffles are needed both above and below the feed inlet. Tracer tests with a fluorescent dye water tracer showed that the addition of the baffles reduced the amount of feed water entrained into the froth at any given coal recovery.

Jan 1, 1994

By A. C. T. Bigg

Heavy media separation is one of a number of ore-concentration techniques for coarse? feed which, when the ore is amenable, offers economic advantages in the mining stage and/or the processing stage. In mining, simpler and cheaper methods may be used if a greater proportion of waste material can be included in the mining blocks that can later be re-moved efficiently at a coarse size. In the mill, pre-concentration can mean considerable savings in capital and operating costs by down-scaling of equipment sizes particularly in the grinding section. Conversely, throughput may be increased using the equipment already in-stalled in the concentrator.

Jan 1, 1988

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By R. R. Klimpel

The process of flotation is an extremely important solids separation technique employed in a wide variety of industrial process applications. Froth flotation is practiced in the coal industry to recover fines produced during the mining and cleaning of coal. A recent review article by Aplan (1) covers the processing variables encountered in the flotation of coal and the variety of chemicals and operating conditions which affect recovery. Numerous engineering and scientific studies have been performed with the goal of providing semifundamental laws of flotation behavior for improved screening of flotation chemicals, better equipment scale-up factors, etc. Often the results of such work are expressed in the form of mathematical models (e.g. 2, 3, 4, 5, 6) which are potentially useful for evaluating (simulating) on paper such alternatives as possibles process operating or configuration changes, the effects of ore and reagent changes, etc. It appears to be commonly accepted that a complete scientific/engineering characterization of flotation is immensely complicated and not sufficiently developed at the present to accurately predict (or understand) many important industrial facets of flotation. Thus, one is often reduced to detailed experimental characterization in both the laboratory and plant in order to fully evaluate flotation changes or alternatives. It is the purpose of this paper to describe a method of batch laboratory data characterization that is useful in evaluating flotation chemical reagents including froth flotation of coal. The approach consists of running a series of time-recovery curves in a batch float cell followed by the computer curve fitting of this data to a series of mathematical models based on semi-physical reasoning. The unknowns or parameters of these models are then optimally chosen so as to best fit the experimental data. It has been found in both coal and mineral systems that changes in reagent type, concentration, system pH, grind, etc. cause very consistent and logical changes to

Jan 1, 1979

By W. L. Freyberger

In many papers concerned with fundamentals of the froth flotation process, authors have considered the contents of a flotation cell to be comprised of two immiscible phases, the froth and the pulp. I (Of course, each of these phases is in turn made up of several solid phases plus air and water.) This generalized concept of the flotation system can be extended by considering the cell contents to include two phases: an extracting phase, the air bubbles plus the collector, which removes a selected mineral component from the second phase, the ore pulp. Thus, there is an analogy between a flotation system on the one hand, and chemical extracting systems, such a solvent extraction system or a leaching system, on the other hand. Such extracting systems may be operated in cocurrent or countercurrent fashion. This paper includes first a brief discussion on the general nature of cocurrent and countercurrent operation as applied to froth flotation, and then presents the experimental results of flotation of a specular hematite ore by each method, using a tall oil fatty acid as collector. Cocurrent Flotation A conventional flotation circuit involving roughing, scavenging, and cleaning flotation is illustrated schematically in Figure 1. In such a circuit the col¬lector, or extractant, and new feed ore enter together at the head of the rougher circuit, and flow cocurrently to the scavenger circuit where more collector is added. According to this practice, sufficient collector is added to the head of the rougher (and scavenger) so that the final tailings are of low enough grade to be discarded. Since the flow of collector and ore is cocurrent, the process consists of single stage contact between the extracting phase and the ore pulp. If the scavenger concentrate is recycled to the head of rougher, the overall circuit has some of the characteristics of countercurrent flow. In such a case part of the extractant (collector) is added at the discharge end of the circuit, and may

Jan 1, 1971

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017