Search Documents

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By S. B. Kim, J. Hong, K. Park, W. Kim, H. Kim, Y. Han, J. Choi

"For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50–200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.INTRODUCTION A great number of potential applications of lithium are being developed currently by the thermonuclear fusion power generation industry(1,2) as well as by the battery and fuel cell industry(3). Even though lithium is mainly consumed in the form of lithium metal and some lithium compounds, about 10% of total lithium production is consumed directly as mineral concentrates by the ceramic industry for the manufacture of special ceramics and mica based glass-ceramics(4). Granitic pegmatites normally contain feldspars, quartz, and mica in addition to lithium-bearing minerals such as spodumene (LiAl(SiO3)2), petalite (LiAlSi4O10), and lepidolite (KLi2Al(Al,Si)3O10(F,OH)2). The amount and grade of metallic minerals tend to gradually decrease and become lower, leading to the increase in the price of base metal or metallic compound(5). Accordingly, recent studies have been extensively devoted to developing the technique to improve the grade of metallic minerals from low grade metallic ores(6,7). Nevertheless, studies regarding the improvement of Li grade from lepidolite ores are very scarce. Lepidolite is a phyllosilicate mineral of the mica group and is often associated with other minerals such as calcite, muscovite, feldspar, and quartz, which need to be separated for lepidolite enrichment(8). Many studies have reported the flotation techniques for separating calcite, muscovite, feldspar, and/or quartz from various targeting minerals(9-11); however, there has been no attempt to investigate physico-chemical properties of lepidolite and its separation from such types of gangue minerals through flotation. Hence, in this study, for the first time, flotation has been carried out for the quaternary ammonium salts (stearyl trimethyl ammonium chloride (STAC, (CH3)3CH3(CH2)16NCl))-lepidolite system based on only the electrokinetic property of minerals that consist of lepidolite ores without adding any depressant to get an initial insight on its flotation behavior. The experimental variables that influence the lepidolite flotation such as amount of collectors, feed size and solution pH have been also examined."

Jan 1, 2015

By George D. Roberts

Dams are constructed to retard the flow of water or debris; therefore natural forces are constantly at work to remove such obstructions. To circumvent nature and avoid expensive trouble with a dam requires thoughtful far-sighted planning, careful construction control and vigilant periodic inspections to detect and repair deterioration at its inception. Although the factuality of the foregoing statements is apparent, all too many have failed to consider them in the past as will many in the future. "The economic, but safe construction of dams calls for the highest order of technical knowledge, practical experience and sound judgment." (1)

Jan 1, 1967

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021

By Se-joon Kim, Jong-hwa Chun

"‘Gas hydrate’ is the common term for a solid material formed from the combination of various gases as ‘guest’ and water as ‘host’. A series of large-scale scientific drilling and coring programmes conducted since 2000 revealed that natural gas hydrate exists in a wide variety of accumulations in the sediments. The scaled-up onshore and offshore field production tests during the last decade show that gas production technology will be realized to make gas production from gas hydrates viable in the future, recognizing its potentials as one of the future sustainable energy resources.The total produced gas was approximately 470 m3 by the hot water circulation method over 6 days of operation in the permafrost-associated Mallik 2002 project in the Mackenzie Delta of Canada. In the Mallik 2007-2008 project, the gas was successfully produced stably by the depressurization method for 6 days, up to 13,000 m3 cumulatively. The depressurization method applied in the Mallik test was shown to be an effective way to produce gas from gas hydrates. The Alaska field trial to inject mixed gas of CO2 and N2 to exchange CH4 in 2012 was successfully done for the first time to produce maximum 1,270 m3 per day. A remarkable achievement was made by Japan when it completed its first offshore production test in the Eastern Nankai Trough, producing approximately 120,000 m3 of methane by the depressurization method over 6 days in March 2013. The technical challenges and scientific uncertainties obtained from Nankai Trough production test provide Korea with more considerations as to the aspects of well completion, reservoir formation and seafloor stability, sand control, flow assurance, environmental monitoring, and etc., due to the different geological setting and geomechanical properties of the Ulleung Basin in Korea."

Sep 1, 2014

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Simon D. Strauss

This paper discusses the ways in which the metals industries dealt with surplus capacity in the past, primarily the twenty years, 1950 - 1970. During this period, the bulk of metals production in the market-economy countries was controlled by private sector companies. Since then, public sector companies have played an increasingly important role in the metals industries of the market-economy countries. Of course, the change was not overnight. It occurred gradually over a period of many years. Indeed, by 1965, several developing nations had adopted policies of government control of metal operations previously in private hands. The metals industries are so many, so large and so diverse that the constraints of time make it impossible to deal with all segments. To illustrate the problems of surplus capacity in the metals industries during the period, this paper focusses primarily on three metals. One experienced rapid market expansion between 1950 and 1970; one had a growth more or less in line with the expansion of the world economy; and one lagged well behind the pace of industrial expansion. No one will be surprised if aluminum is identified as the metal with rapid growth; copper is identified as the metal that kept pace with the world economy; and tin is identified as the laggard. Individual computations of the rate of growth for these metals show some variations, but most estimates place the increase in aluminum consumption in the market economy countries between 1950 and 1970 at a compound annual rate of about 8%. The corresponding figure for copper is a compound rate of 4%. Tin consumption showed no growth. A widely accepted point of view is that sharply rising demand will force the price of a commodity to increase substantially in order to attract a necessary expansion of supply. The corollary to this is that stagnant demand will hold prices down, as there is no need to stimulate new supply and it may be necessary to force marginal producers out of the market. The experience with aluminum, copper and tin in the years 1950-1970 does not support this theory. In 1950, the average prices in the United States market as reported by the American Bureau of Metal Statistics were 17.74 a pound for aluminum, 21.24 a pound for copper, and 95.54 a pound for tin. The corresponding figures in 1970 were 28.74 a pound for aluminum, 57.74 a pound for copper and 174.24 a pound for tin. Aluminum, with the greatest market growth, rose by 60%, whereas tin rose 82% and copper by 172%. Clearly, other factors were a more important influence on price than was the trend of demand To revert now to the capacity issue, during the period under review aluminum demand was rising so sharply that that industry had no sustained problem with surplus capacity. Instead, if anything, capacity may at times have been a constraint on demand. The industry succeeded in attaining explosive market growth through imaginative research and promotion programs. Some of this growth was the result of substitution of aluminum for other commodities – steel, copper, wood and glass as examples. But much of the growth was the consequence of developing entirely new products through technological innovation. Prior to World War 11, the number of aluminum producers was extremely limited. Alcoa and Alcan in North American and Pechiney and Alusuisse in Europe were the dominant firms. The developing countries had virtually no production and in Japan and Germany production was only a small fraction of the North American output. During the War years the United States had financed the construction of many new facilities. After the war these plants were sold by the government to Reynolds and Kaiser in order to foster more competition in the market. Subsequently many other concerns became aluminum producers, both in the United States and elsewhere and competition for markets intensified.

Jan 1, 1989

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice (USPAP) and the Australian VALMIN Code to a complex mineral property appraisal assignment and previously to some modest assignments. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others and information and statements required from the client under the VALMIN Code. The exercises highlighted many positive features of both sets of standards. However, the author concluded that, without modification, VALMIN is incompatible with USPAP and the US regulatory environ¬ment. The author found that VALMIN violates US legal decisions regarding real property appraisal due to its requirement to include many items of business value. The US Securities and Exchange Commission's prohibition on reporting quantitative resource estimates proved to be a severe problem under VALMIN. Some VALMIN requirements could not be met due to the extent and quality of documents specified. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed. Management considerations for complex mineral-property appraisal assignments are also presented.

Jan 1, 2000

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By David Mast, Irwan Halim, Brian Hagan, Kaveh Talebi, Jason Edberg, Amanda Foote

On June 14, 2023 Jay Dee Contractors’ Tunnel Boring Machine (TBM) “Phoenix” holed through and completed mining the second drive of the I-75 Segment 3 Storage and Drainage Tunnel. Completion of the tunnel came only after overcoming several challenges, including a groundwater intrusion event which deposited thousands of cubic yards of wet ground material into the tunnel. This paper will discuss the events which delayed completion of the tunnel by over nine months, the risk management and construction approaches assumed by the Design-Build team during bid, several challenges faced by Design-Build teams when building stormwater resilience tunnels using traditional Department of Transportation standards, and recommendations for improving risk allocation and proposal documents for future similar Design-Build tunnel projects.

Jun 23, 2024

By Todd Kilduff, Paul Wilkinson

Microtunneling is rarely a straight forward “business as usual” endeavor. More often than not, these projects take twists and turns that require on the fly, out of the box solutions to get the project completed. This paper is a case history of a 63-inch diameter, Permalok, microtunneling project, extending nearly 700 linear feet under a hill forming the left-hand abutment to an earth embankment tailings dam. The job had three major and unexpected challenges that required unorthodox solutions. Challenge #1— Face Configuration: The Santiago Formation, a cemented sand formation with widely varying strengths, presented a challenge to configuring the face with regards to the number and length of pics and cutters. Subtle differences in type and size of the tooling had a big impact on the performance of the machine. Challenge #2—Eccentric Loading: Issues at the launch shaft with the Permalok pipe adaptors caused eccentric loading on the casing pipe. This issue resulted in overstressing and breaking of several pipe joints that ultimately led to seizure of the tunnel. Challenge #3—Back-tunnel Excavation and MTBM Recovery: There were many detailed considerations into excavating a recovery tunnel to retrieve the MTBM, especially being under a high hazard earth embankment dam.

Jun 13, 2021

By Edward C. Dowling

Cleveland Cliffs and affiliated companies have established a commitment to the development and use of integrated process control. Substantial capital investments in process control, coupled with the dedication of human resources to effectively use the information, have generated meaningful business results. Improvements in productivity, operating costs and product quality have been realized. This paper presents an overall process control and information strategy, specific case studies, lessons learned and the current view of the next steps in the continued journey toward integrated process control and information management.

Jan 1, 2000

By Shinichi Konda, Gary Nishimura

"Thousands of years ago large glaciers carved much of the landscape in Puget Sound, depositing abrasive and granular soils including cobbles and boulders along with layers of clay and sand. Tunneling in this geology – common throughout much of the northern and Midwestern U.S. – is challenging and can be unpredictable. The use of pressurized face tunneling, most commonly with EPBs and slurry type machines, has made excavation in this geology more efficient, but difficulties still remain. Through analysis of recent projects in Seattle, Washington, USA, the authors draw conclusions as to the best TBM designs and operational parameters for this variable, abrasive and often difficult ground. Performance data is analyzed with an eye towards advancements that could further improve TBM tunneling in glacially deposited soils. INTRODUCTION Over the past several ice ages, extensive glaciers reaching across much of North America transported large amounts of soil and rock as they moved across the land. The substantial weight of the ice sheets mixed together a wide range of soil types along with a variety of rocks and boulders of all sizes. Many rock formations were reduced to pebbles or particles containing highly abrasive characteristics. Any boulders able to survive were generally comprised of harder materials which were scattered throughout the soil. This highly variable mixture of abrasive soils and high strength boulders can be found in many areas across the Puget Sound and other regions of the country. Wherever they are encountered, they often create a difficult and unpredictable mining environment for both equipment design and operation. Modern TBMs are optimized early in the design process for specific types of geology, and unexpected conditions can require extensive modifications. In addition, several operational parameters need to be adjusted to balance ground characteristics, and advance rates can be significantly affected in mixed and rapidly changing soil conditions. Both EPB and slurry machines can be used successfully in these conditions, provided their respective operating criteria are met. Ideally, an EPB is operated with a relatively thick muck consistency, which accommodates moderate changes in soil permeability and maintains a reliable pressure differential through the screw conveyor. However, this also causes higher wear on rotating components and requires more energy at the cutterhead. Alternatively, slurry machines typically operate best with a more fluid muck consistency that can be easily pumped through the extensive piping system. This tends to reduce the wear on the cutterhead and the power requirements of the cutterhead drive system, but also makes the machine more sensitive to changing soil conditions. Generally, the slurry piping system is also more capable of controlling high face pressures, although the screw conveyor of an EPB can also be designed to accommodate most high-pressure conditions."

Jan 1, 2016

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment like haul trucks are a major safety concern in the U.S. mining industry. They account for more than 50 percent of surface mine fatalities each year [1]. A recent National Institute for Occupational Safety and Health (NIOSH) analysis of 91 fatal incidents identified loss of vehicle control and situational awareness as key contributors [2]. However, the first-hand perspectives of operators are often missing, emphasizing the need for deeper insights into operators’ decisionmaking, lessons learned, sensory cues and mental strategies used during near-miss events. The findings in this analysis will help inform the development of training and safety solutions to prevent or reduce haul truck accidents.

May 1, 2025

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By M. L. Chapman

When originally accepting the assignment, the Client had described the property as vacant land. A prior appraisal was later discovered and revealed that the property included a mineral rights appraisal. Further research disclosed an old dispute with a court ruling based on testimony by AIMA-certified experts. The present appraisal was therefore based on data from findings of the court with a fresh look at discount rate, absorption period, and residual land value. Fortuitously, the property subsequently sold on the market, while meeting all criteria for Fair Market Value. This provided insight into a market-based discount rate. Also, the absorption period could be adjusted in accordance with the current market conditions. The residual land value was minimal (based on comparable sales and projecting trends in market) as the property was affected by a flood zone and the surrounding development was sparse. PROPERTY HISTORY: A GREAT INVESTMENT Briefly, the subject property is located in the floodplain region of the San Jacinto River, a short river in southeastern Texas that flows into Galveston Bay, filled with sand and gravel. This location is on the north side of Houston, north of Beltway 8 on the east side of I-59.

Jan 1, 2012

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By Yuan Le, Dominic Reda, Vojtech Ernst Gall, Kurt Zeidler, Tomasz Kecerski

High Speed 2 (HS2) mandated that Building Information Modelling (BIM) processes be implemented during design and construction. Gall Zeidler Consultants (GZ) was responsible for developing the BIM Models for the portals, tunnels, and cross passages of the of the 16 km-long Chiltern twin-bore Tunnel. In addition, GZ developed the GBR for the Chiltern Tunnels and incorporated the relevant information into the Project’s BIM framework. This paper presents the implemented BIM framework, describes the modelling approach, and discusses the advantages and challenges of implementing BIM, particularly how BIM improved interface coordination and how BIM was used in feasibility assessments of different construction options.

Jun 13, 2023