Search Documents

By B. H. Kaye

Particle-size Distribution Specifications for Particulates. Feed to and finished products from size-reduction operations are defined in terms of the particulate sizes involved. It is also well to know whether the ultimate individual particle is being measured, or, if any aggregation or agglomeration of particles exists, whether this has been created by the size-reduction operation. The most complete description of a powder is given by its particle¬size distribution. This can be plotted in terms of cumulative percent oversize or undersize in relation to the diameters of particles, or it can be plotted as a distribution of the amounts present in each unit of diameter against the several diameters. It is common to employ a weight basis for percentage, but there are some data in the literature where frequency, or number of particles, is used. The basis of percent¬age, whether weight, frequency, or some less commonly used factor, should be specified, as also should be stated the diameter, its units, and preferably whether determined by sieve, settling velocity, or other¬wise. Fig. I presents two sets of distributions-ore cumulative and the other in unit intervals. The slopes of the 5-µ intervals of the cumulative curves are converted to percent per micron and plotted as a block, or histogram, from which smooth curves are derived. Powder A has a narrower, or tighter, size range for the bulk of its weight than powder B. Both materials have the same weights below and above the size marked by the arrow. Simpler treatments of distribution are possible. In some cases the significant value is the top size. Since the 100% point is dubious, some amount, as 95 or 98%, so specified, can be called top size. In other cases the percent on some sieve helps define coarseness. Merely stating that all, or all but a small percentage, passes a given sieve is inadequate for defining the true fineness or a material. Complete parti¬cle-size analysis to show the distribution is essential for most compari¬sons and calculations. Particle-Size Equations. A number of equations have been pro¬posed to correlate the quantity of a particulate material with its parti¬cle size to obtain a distribution relationship. 's 19 In the literature it is often assumed that a powder must follow some distribution, such as the Rosin-Rammler-Bennett:20, 21

Jan 1, 1985

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. An alternative parameter, the organic efficiency, does indirectly consider process economics, but it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach, the partition moment of inertia, is introduced. This parameter reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure that promises better use of performance data. IntroductionPartition curves are commonly used in the characterization, evaluation and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, density separators and other beneficiation technologies that are based on intensive physical properties. Graphically, the partition curve depicts the recovery of particles as a function of the physical property on which the separation is based, such as particle density, size or magnetic susceptibility. Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic S shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout, or bypass, values; the midpoint slope; and the separation cut point, defined as the property value with 50 percent recovery.Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, as a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point, that is, an infinitely large slope. One common formulation of this slope, the Ecart Probable, Ep, is derived by evaluating the slope between the 25 and 75 percent recovery points:"

Jan 1, 2016

By Sue W. Wells, James J. Moore, Stephen D. Lynch, R. Hunter White

This paper describes the products and services that Phelps Dodge Corporation desires from solvent extraction reagent suppliers and the partnering relationship that Phelps Dodge wishes to develop with these suppliers. Product topics include: 1) manufacturing concerns, 2) product and process quality control reporting and 3) reagent customizing to meet individual plant needs. Service subjects include distribution, delivery time, emergency re-supply, terms, and tailoring technical support. The partnering relationship discussion reviews mutual benefits, communications, reliability, cross-functional teams for problem solving and developing new opportunities, and long-term commitment.

Jan 1, 1994

By P. James, L. J. Steiner, F. Turin

NIOSH researchers and an industry partner conducted an investigation to study the effectiveness of ergonomic interventions in mining. The study required a significant commitment of time and resources from the cooperating site, Bridger Coal Company. This paper focuses on some of the challenges faced by the researchers and their cooperator. Challenges included the need to redesign methods of identifying and prioritizing injuries, and the need to train the workforce in ergonomics while still maintaining progress and interest in the process. The authors discuss some practical interventions implemented by Bridger Coal to date, and discuss future research implications brought about by PacifiCorp’s Generation Business Unit, who monitored the project to determine whether an employee-owned ergonomic process could be implemented throughout their operations.

Jan 1, 2003

By Patricia O. Milley

Two years ago, AlliedSignal embarked on a journey to improve QUALITY. However, the focus of this endeavor was on the CUSTOMER and not the traditional product focus. It wasn't that a focus to improve product quality wasn't fruitful in the past. We've practiced it in the chemical industry for many years with significant results. But our industry today is in a survival mode and yesterday's way of doing business is simply not good enough. In the mining industry, we have to make lug strides in how we do business or face losing our customer base. As you are well aware, other parts of the world are importing our technology at a rapid rate. We must work smarter to stay ahead of our customers ever more demanding need for higher quality at lower prices. With this as a driver, throughout the Corporation we reviewed in depth how we support our customers to keep them competitive and sought to eliminate work which did not help them reach this goal. Our first year of emphasis was on tools: how to hold meetings, gather data, and how to make decisions. This sounds very basic, I know, but you can't begin to imagine how productive meetings can become when you start with an agenda and prework delivered days in advance, and agree at the start of the meeting what should get accomplished. In the second year, we applied these tools to our work processes. We mapped how we do our work, scrutinized each step for value to the customer, and then set to work on how we could do things better. The areas we concentrated on were customer linked commercialization of new products, manufacturing and materials management. Our discussion today will focus on the commercialization of new products.

Jan 1, 1994

By Douglas J. Pendrell, Marvin D. Simmons, E. Raymond Boc

The U. S. Army Corps of Engineers is in the early stages of design for an estimated 14 m (46 ft) diameter tunnel in northeast New Jersey. This tunnel will carry flood waters from the upper end of the Pompton River in Wayne County, to an outlet in Newark Bay, a distance of 33 km (20.5 miles). The tunnel will be constructed by a tunnel boring machine (TBM), the size of which is unprecedented at the present time. The alignment is through Triassic and Jurassic sandstones, siltstones, and shales that include three beds of basalt that range in thickness from 76 to 310 m (250 to 1020 ft).

Jan 1, 1991

By R. A. Lowe, P. B. Malla

Smectite is a common impurity in the kaolins of Georgia.This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms ahydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By L. Alan Weakly

Coal mines and power plants utilize different methods to control dust for the safety of their workers and to protect their installations. The methods that they use are limited by the Environmental Protection Agency or the states in which they operate. Now there is a new technology for controlling dust at conveyor transfers! The Passive Enclosure Dust Control System utilizes several proven technologies to mitigate fugitive dust. This new system has been proven to be four times more effective than standard enclosures utilizing bag house collection and is considerably less expensive to install and operate.

Jan 1, 2000

By G. L. Mowrey

A new coal interface detection (CID) method is under investigation by the U.S. Bureau of Mines. This novel concept is based on utilizing a passive infrared system (FIR) to measure temperature changes associated with the cutting of coal and adjacent strata. For this method to work successfully, a definite mechanical/hardness contrast must exist between coal and rock. Advantages include that FIR responds instantaneously at the coal-rock interface and it is minimally affected by dust and/or water sprays. Based on preliminary tests, results indicate that the PIR method can be applied successfully in mines having a hard immediate roof.

Jan 1, 1990

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By A. J. Hudson, M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow leakage of currents into the mine roof, which may ultimately result in the combustion of the roof material. The National Institute for Occupa¬tional Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), devised a passive means to detect overheating insulators on di¬rect current systems. The detector consists of a spring- loaded car¬tridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can easily be installed over the outer metallic shell of an existing trolley line insu¬lator. If an insulator overheats due to ground leakage currents, the vis¬ible streamer alerts mine personnel traveling on the haulageway.

Jan 1, 2000

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By James J. Gusek

Passive-treatment systems that mitigate acid-rock drainage (ARD) from coal mines have operating since the mid-1980s. Large systems at metal mines are being contemplated. A 95L/sec (1500-gpm) capacity system is planned this year at an underground lead mine in Missouri. Mine, process and environmental managers need to understand how and why passive-treatment systems work. They must understand what operational limitations to expect, as well as the economics of construction and operation compared to the alternatives, like lime precipitation. Wetlands have been recognized as nature's method of improving water quality. Contaminant reductions can occur through the precipitation of metal hydroxides, sulfides and carbonates and pH adjustments. Local conditions, oxidation state and water and soil chemistries dictate whether these natural reactions will occur under oxidizing (aerobic) or reducing (anaerobic) conditions.

Jan 1, 1995

By M. C. Roberts

To assess the future markets for a mineral from a producing district, the following three aspects must be considered: the future growth of the markets, the competitiveness of the district in terms of production costs and reserve adequacy, and the competition from alternative sources of supply. This paper focuses on the first issue by developing a method for predicting the demand for phosphate from trends in the major market for phosphate products, the fertilizer and agricultural market. The paper shows how broad changes in this end-use market for phosphate has evolved over time. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 2000

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By Ava Walker

The first form of a surety bond was an honest handshake between two or more parties agreeing to a decision, and their personal guarantee of following through to completion. This has all changed. In 1895, the United States Treasury Department disclosed that $35 million worth of personal surety guarantees on file had become worthless. A law was then passed requiring all surety bonds, in favor of the United States, must be corporate surety bonds. Today, a surety bond is one of the nation's leading fi¬nancial instruments used to guarantee the completion of an obligation. One hundred-fifty years before cor¬porate surety bonds, outcrops near Richmond, VA, were being mined. These surface mines became under¬ground mines. Today, both are still being used to obtain a leading energy source, coal. Since that time, more than 5956 km2 (1.47 million acres) of coal mined lands have been reclaimed in the US (Coal News, August, 1987). More than 25,000 state and Federal mining permits cover¬ing 14,164 km2 (3.5 million acres) have been issued during the last 10 years. Coal production has exceeded 7.2 Gt (8 billion st). More than 5665 km2 (1.4 million acres) of mined land has been reclaimed by active coal mining opera¬tions and 267 km2 (66,000 acres) of abandoned mined lands have been re¬claimed by others. Reclamation bonds were freely writ¬ten in the 1970s. So why are they almost extinct today? Contract bond losses have been severe in the past several years, sureties reporting losses exceed¬ing 110%. But the same proof is not provided on coal reclamation bonds. A surety bond is generally required when one party has an agreement with another party, and that party wants a guarantee from a third party that a job will be completed according to the terms and conditions of a written contract. In the case of a reclamation bond, the surety company (surety) is the financial party. It extends the credit and a guarantee to the obligee (the State, Commonwealth, or Office of Surface Mining) that the principal (the coal operator/company) will complete the terms and conditions of the contract (the rules and regulations governing mining and reclamation). The Surety Association of America defines a surety bond as an agreement providing for monetary compensation should there be a failure to perform specified acts within a stated period. Webster's Dictionary defines surety in the following ways: "l: the state of being sure; 2a: a pledge or other formal engagement given for the fulfillment of an undertaking and; 3b: one who has become legally liable for the debt, de¬fault, or failure in duty of another." Banks never make accommodation loans. Either the loan is good or no loan is made. Surety companies feel the same way about surety bonds. In fact, the average person does not realize the dangers of becoming surety for another. How does a surety determine if a company is worthy of receiving surety credit? How is a coal account under¬written today for an obligation that may not be released for many years? When a surety company executes a reclama¬tion bond, it financially puts its name behind the coal company and its guaran¬tee that should the coal miner default on the obligation, the surety will fulfill the contract. How is the surety to determine if a coal company may still be in business five, 10, 20, or 40 years from today?

Jan 1, 1989