Search Documents

By M. B. Freeman

Acrylic polymers have been found to be effective dispersants and stabilizers in a wide variety of mineral processing applications including rheology control in concentrated slurries. This paper will describe these low molecular weight, water-soluble polymeric dispersants and provide a basis for how they function in concentrated slurries based on computer molecular modeling and applications results. Data on homopolymers as well as copolymers of acrylic acid will be presented to demonstrate the optimization of a polymeric dispersant in preparing high solids slurries of inorganic materials such as kaolin, calcium carbonate, lime, and magnesium hydroxide.

Jan 1, 1996

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

By Rosario Lunar, Jesús Martínez-Frías, Egidio Marino, Trinidad Torres, Jose E. Ortiz, Juan A. Martín-Rubí, Luis Somoza, Ricardo León, Teresa Medialdea, Javier González

Seamounts, submarine banks, volcanoes and undercurrent channels are prominent geomorphic features that have become an important target for minerals research and exploration with the goal of future exploitation. Polymetallic ferromanganese deposits are common types of mineralization on these settings. Co-rich ferromanganese crusts are important as potential resources of Mn and Co, but also Ti, Ni, Tl, REEs, PGEs, and other metals. Many seamounts and channels along the Atlantic Spanish continental margin are known to hold mineral deposits but are poorly studied. This work presents and briefly describes the most recent activities of the Spanish Geological Survey (IGME) on exploration and investigation of ferromanganese deposits along the Atlantic Spanish continental margin. Different submarine areas from the northwestern margin of the Iberian Peninsula to the west off Canary Islands have been surveyed by geophysical, sampling and underwater observations from 89 to 4000 m water depth. The mineral deposits cover a large diversity of submarine geological and geomorphical features: mud volcanoes and diapirs related to hydrocarbon seeps, seamounts associated with hot spot volcanism, hydrothermal vents in active magmatic volcanoes, structural basement highs and banks or contourite channels. Considering the collected dataset, we present the preliminary results of the study of these mineral deposits, including ferromanganese nodules and crusts and phosphate pavements and nodules, which can be considered as potential sources of raw materials.

Sep 1, 2014

By S. Hearn, S. Boskovic, A. Smethurst

"The digestion of minerals in strong acids or at elevated temperatures can result in the release of large amounts of silicic acid which can polymerize in solution to form colloidal silica and gels. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Huntsman’s POLYSIL® polyether coagulants have a “lock and key” relationship with the surface of colloidal silica to help lower the concentration of these particles in solution, improve process efficiency and reduce reagent losses by minimizing crud formation. This paper investigates some of the issues caused by colloidal silica in hydrometallurgy processes and illustrates how the use of POLYSIL® coagulants has helped to improve process outcomes. INTRODUCTION Coagulation differs from flocculation in a number of ways. Coagulants are relatively small molecules that modify the surfaces of fine particles, weakening repulsive forces between them and allowing particles to stick together, while flocculants are generally molecules that are large enough to bridge the boundary layers between the particles. With flocculation, addition rate and mixing all make a difference to the flocs formed. Coagulation, on the other hand, is an equilibrium process. With coagulation it is only necessary to achieve good mixing, and coagulates will form as Brownian motion pushes the particles into each other. In real systems, this process is complete within seconds. Huntsman’s POLYSIL® polyether based coagulants have a strong affinity with the surface of colloidal silica formed by the polymerization of silicic acid. While silica found in minerals has a low aqueous solubility, large amounts of silica as silicic acid can be released as these minerals are digested in strong acids at elevated temperatures. The solubility of free silicic acid is about 150 ppm under pH conditions typical in acid leach environments (1), so the bulk of the silica will polymerize in solution to form colloidal silica. Colloidal silica can pass through a hydrometallurgy process without affecting any of the operations. However, it can cause a number of problems. These include gelling in a leach, interfering with flocculation or crystallization, initiating crud formation (2,3,4), decreasing extraction kinetics and increasing phase disengagement times (5,6) in solvent extraction. In these cases, coagulating the silica with POLYSIL® coagulants can reduce or eliminate the problem by enabling these particles to be flocculated and removed from the solution."

Jan 1, 2015

By D. Earley

High metal prices and new world trade standards and accounting for environmental liability in financial disclosures are creating markets for metals commodities that are produced using ?green technologies?. A promising "green" gold leaching system uses a polysulfide based lixiviant which is non-toxic and non-polluting. Laboratory testing has demonstrated selective gold extraction rates comparable to those of cyanide. The polysulfide lixiviant is a dilute aqueous solution which can be inexpensively produced from readily available chemical reagents and even mining wastes. The reagent system is self-buffering and maintains the optimal chemical environment for leaching. Treatment of residual leach solutions is not necessary because the lixiviant itself is not toxic, and breaks down as the system equilibrates. Simple closed system boiling is used to recover gold from process solutions. The polysulfide lixiviant can then be readily renewed and recycled back into the system, forming a closed loop system that conserves reagents and energy which minimizes operating costs. Economic projections have shown that the system can be used profitably for standard ore types and grades.

Jan 1, 2009

By Delbert Hamilton, Christopher Snyder

In the last three years there have been four uncontrolled heating events in mines that have been attributed to the use of polyurethane foam as a void fill product. These heating events are due to the exothermic reaction that occurs during application of these polymeric products. These events led the Mine Safety and Health Administration to issue a safety alert on polyurethane products used in void filling and ground consolidation in mining, with the goal of educating the mining community about this potential hazard. This paper provides an overview of various types of polymeric products and best practices, the factors that contributed to the heating events, and case studies involving polymeric products.

Jun 25, 2024

By A. Koski

A pond rehabilitation and environmental education project were proposed by Cleveland-Cliffs Michigan Operations (CCMO) and approved by the Michigan Department of Environmental Quality (MDEQ) and the United States Environmental Protection Agency (USEPA) as partial fulfillment of conditions for a stream mitigation permit. The goals of the project were the rehabilitation of a pond on a tributary of a local trout stream, enhancement of public access and appreciation, and the initiation of a site-based environmental educational curriculum. Cleveland-Cliffs undertook a suite of actions to rehabilitate a pond created by a previous mining operation in 1912 and make accessible to local schools the aquatic and riparian ecosystems. Cleveland-Cliffs partnered with the local governmental unit and two local school districts. The rehabilitated pond and riparian zone provide an accessible natural area that local residents can use for such activities as hiking, biking, walking, fishing and nature study. Vegetative enhancement includes the planting of native shrubs, wildflowers and showy herbaceous plants in the pond, on the riparian fringe and the surrounding area. An interpretive trail was developed around the pond with signs created by a local master watercolor artist. Local schools built and installed picnic tables, benches and a kiosk. Cleveland-Cliffs created pond lesson plans tied to the Michigan Curriculum Framework, developed inexpensive teaching kits and hosted a workshop for teachers from nine local schools. Classes regularly utilize the pond during the school year conducting environmental studies. Nesting boxes, wildflower gardens, bat houses, frog deformity surveys and water quality studies are a few of the activities that classes have conducted at the pond.

Jan 1, 2007

By A. D. Randolph

Comminution represents one of the major costs of mineral recovery from low-grade ores. Efficient mineral recovery in a typical low-grade ore grinding-flo¬tation process depends on grinding the ore small enough to liberate mineralization without producing excessive slimes, which would result in higher power and flotation reagent costs. Size criteria for efficient grinding should be stated in terms of the distribution of mineralization sizes, but as the mineralization-size distribution is difficult to determine, less desirable criteria of absolute particle-size distribution (PSD) are used in practice. Thus, there is considerable incentive to be able to analyze and predict the PSD performance of grinding circuits for control and optimization of the process. Any realistic model of a grinding circuit must account for recycle of oversize material; such oversize recycle adds to the total mill load and limits total production rate. Simulation of such closed-circuit operation to study grind factors affecting total throughput can be done in a straightforward fashion provided recycle calculations can be added to an accurate input-output model of PSD in the grinding mill itself. Such a total simulation of mill performance is of obvious practical value in assessing the practicality and benefits of various over-all mill control schemes and/or modes of operation. For example, considerable interest has been shown in the development of continuous on-line particle-size sensors and such instruments should be an operating reality in a few years. A total closed-circuit PSD model of this type would be invaluable in the utilization of, and in predicting the pay-out from, such an on-line particle-size sensor. The purpose of this paper is to present a new approach to the development of an input-output PSD model of a grinding mill. The model is continuous in the par¬ticle size coordinate, L, and is based on the principle of a particle population balance along the particle size coordinate. Most previous studies of the grinding unit operation attempt to relate power

Jan 1, 1971

By Paul Dean Proctor

The world's population by 2000 A. D. may approximate 6.5 billion and the United States' 304 million. South Asian population increases between 1970 and 2000 A. D. will be triple the projected population of North America. Such anticipated dramatic and probably traumatic increases in world population yield grave concern for the standard of living in the world and the United States. The people of the United States currently consume 32 percent of the world's energy and similarly large percentages of the world's mineral raw materials. With only 6 percent of the present world's population and slightly smaller percentage by 2000 A. D., much expanded world-wide production of energy and raw materials will be required to maintain even a standstill living standard. A minimal 2 percent increase per year in the standard of living in the United States and a 4 percent increase elsewhere in the world, beyond the demands of the estimated population increases, suggest the magnitude of the increased need for energy-mineral raw materials and the possible crises the world will face in these areas by 2000 A. D. Mineral engineers and scientists with broad educational backgrounds will be required in greatly increased numbers to help alleviate, and possibly avert, expected energy-mineral raw materials shortages of the next millenium. Explorationists, mineral engineers, commodity economists, environmentalists, city, county, state, and federal mineral materials planners and coordinators, and metallurgists will be among those most needed. AIME membership in the second century of the Institute's history will contribute directly to this personnel pool.

Jan 1, 1971

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world's first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth's crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world's most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah' and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By Sergey N. Zhurin

At Gubkin Mine (Korobkovo Iron Ore Deposit, Russia) tailings are being pumped into two experimental stopes. Slurry has water content that exceeds 80%. In-situ measurements were conducted to determine pore pressure distribution in the backfilling panels. Numerical FEM modeling has been implemented to infer pore pressure distribution within filled cavities. Field observations reveal that pore pressures within neighboring stopes are slightly interrelated, because of drift connecting stopes at its bottom and single drainage system occurrence within filled caverns. Both extensive field data and numerical analysis demonstrate that water pressure on the bulkhead depends predominantly on filtration rate through bulkhead filters.

Jan 1, 2001

By Neil Hillhouse

The Porgera gold district, like many other large gold deposits, has a long history of awareness, but only in the last five years has a geologic understanding of the district permitted the discovery of economically attractive gold reserves. The following sequence of events highlights the various significant steps in the evolution of the discovery process. The history of the district goes back about 50 years, and for several decades it was known only for its placer gold. Gradually, as gold became a more interesting metal, more and more attention was centered on the district. The sequence of events does not overstate the problems caused by isolation and climate, but the reader can imagine the difficulties inherent in such an area.

Jan 1, 1990

By D. Robert Weir

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation in order to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration.

Jan 1, 1986

By Eugene W. Price

One of the most important fundamental characteristics of iron ore pellets is their porosity. This importance arises from the fact that the pores are the busy avenues whereby many changes are brought about in the life and form of the pellet from the time it is made until the iron it contains emerges as a molten stream from the blast furnace. As a green iron ore pellet is first heated in the drying cycle of a typical heat-hardening process, the pores act as conduits to allow the escape of steam from the water or vapor from the oil which served as binders to hold the green pellet together. After the release of the steam (or oil vapor) the pores then act as conduits whereby oxygen can enter the pellets to 1) convert magnetite (Fe304) to hematite (Fe203), if appropriate, and 2) promote solid state grain growth between adjacent particles of iron ore. The rate of oxidation and the rate of grain growth are directly related to pore size' and pore size distribution. Rate of oxidation is also directly influenced by length of pore and length of pore is obviously related to pellet diameter. It is well to keep in mind that the heat-hardening process does not harden the mineral grains themselves. What it does is weld them together to change the green pellet from a doughy mass, composed of thousands of tiny individual particles, into a strong, intergrown monolithic structure. In the blast furnace the pores again act as conduits for gases, but in this case they trans¬port reductants such as hydrogen (H2) and carbon monoxide (C0) which remove most of the oxygen from the ore. Rate of reduction is also directly related to pore size and pore size distribution.

Jan 1, 1967

By Marvin P. Barnes

An attempt has been made to compile and code geologic data relating to twenty of the major porphyry copper districts of North America in such a manner as to permit the use of modern electronic digital computers to retrieve, compare, and build statistical mathematical models from the input. In the exploration process as part of his broader efforts to evaluate the potential of some prospective region, district, or ore body, the experienced geologist consciously or subconsciously compares and fits the observed geologic features to similar phenomena associated with known ore bodies with which he is acquainted. Thus an adequate conceptual "model" of the total geologic environment and type of ore body sought is an essential requirement for the successful exploration effort. Numerous such models of porphyry coppers already exist in the minds and notes of many experienced geologists today. These models are, of necessity, couched largely in qualitative terms and though they may be quite definite in the mind of the porphyry copper expert, the total concept of what constitutes a porphyry copper deposit and environment is difficult to convey in very precise terms. There probably is no such thing as a typical porphyry copper deposit. However, it is well understood that most of the deposits that have been studied have many geological characteristics in common. A logical question then might be: What characteristics are most common or how often do they occur in common, and what is their relationship to other common characteristics ?

Jan 1, 1970

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By Garry G. Lowder

The regional geologic setting is essentially a volcanic island arc built upon an oceanic basement, consisting of basalt and minor pelagic sediments (the Tinombo Formation of Eocene - lower Miocene age. Trail et. al. 1974). -- An east-west chain of intermediate and acid calc-alkaline volcanoes (the Bilungala Volcanics) was built on the oceanic basement during the Miocene. The Bilungala Volcanics are flanked to the north largely by contemporaneous andesites and volcanoclastic sediments of the Dolokapa Formation. During middle to upper Miocene time the Bilungala Volcanics were invaded by large masses of predominantly dioritic intrusive rock and it is within one of these dioritic intrusive complexes, the Bone Diorite, that the cluster of porphyry copper systems occurs. Renewed volcanic activity in the Plio-Pleistocene produced acid pyroclastic rocks (the Pinogu Volcanicsi whose distribution is controlled by present-day topography. Structural trends, largely interpreted from SLR imagery, are pre- dominantly NW or NIWJ. The right-lateral Gorontalo Fault, which trends hW through the town of Gorontalo (Katili, 19691 is the most prominent structural feature. Many of the major structures in the Tapadaa district have similar orientations and may be sympathetically related to the Gorontalo Fault.

Jan 1, 1976

By R. L. Andrew

The southwest Pacific has produced at least four of the world’s premier porphyry copper-gold deposits, and the current level of exploration is likely to produce even more. An appreciable amount of gold is being produced with this copper, with obvious economic advantages. Gold content, in addition to their large size, makes the southwest Pacific’s porphyrycopper-gold deposits very attractive exploration targets. The recognition of telescoping and overprinting of porphyry systems has produced a greater awareness of the likely surface expressions, in particular the significance of advanced argillic lithocaps in porphyry exploration. The recognition of the spatial and genetic association of porphyry copper and epithermal gold systems (Sillitoe, 1972), as in other parts of the world, has had important implications for exploration in the Asia Pacific region.

Jan 1, 1995

By Cyrus W. Field

The Pacific Northwest as defined in this review comprises an exceedingly large and geologically complex terrain that occupies the 'Western Cordillera mobile tectonic belt. This metallogenic province is approximately 2100 miles long and 350 to 500 miles wide. It extends north-northwest from northern California and Nevada, through western Idaho and Montana, Oregon, Washington, British Columbia, and southwestern Yukon Territory, to southern Alaska, and west from the western flank of the Northern Rocky Mountains to the continental margin (Fig. 1). Many detailed and thorough exploration programs that have been conducted by mining and petroleum companies for over a decade have demonstrated that porphyry-type deposits are both numerous and wide-spread throughout this province. Although the Granby Mining Company extracted about 34 million tons of copper sulfide ore from Copper Mountain during the period 1900-1957, intentional large-scale production of porphyry-type ores was first initiated in 1962. It began at Bethlehem Copper Corporation's East Jersey orebody in the Highland Valley District of south-central British Columbia, approximately eight years after Mr. H. H. Huestis rediscovered that broad zone of copper-molybdenum metallization and recognized its potential significance.

Jan 1, 1973

By Paul Zick

The Port Authority of Allegheny County North Shore Connector (NSC) Project involves TBM excavation of twin 690 m (2,240 lf) precast segment lined light rail tunnels through soil and rock under the Allegheny River and a narrow, downtown city street. The $435 M project is funded 80% ($348 M) by the Federal Government, 17% ($72.5 M) by the State of Pennsylvania and 3% ($14.5 M) by Allegheny County. Along the tunnel alignment are a historic building on shallow foundations, modern buildings on deep foundations, and one building constructed directly over the alignment. The project includes construction of twin 369 m (1200 lf) cut and cover concrete box tunnels and an underground station shell. This paper provides an overview of general site conditions, current project status and construction challenges for the Twin Tunnels and North Shore Light Rail Station.