Search Documents

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982

By Kenneth K. Humphreys

INTRODUCTION At the time the 4th edition of this book was published in 1979, the coal industry had experienced a sharp upturn in prices for its product. From 1950 throgh 1969, steam coal prices had held almost flat at about $5 US per st (about $5.50/t). Thus, when considering the effects of inflation, the price of coal had actually been declining for two decades. The passage of the Coal Mine Health and Safety Act in 1969 and its cost effects started an upward trend in coal prices which was rapidly accelerated by the effects of the Mid-East oil embargo in 1972. Prices of steam coal on the spot market eventually climbed to over $30 US per st ($33/t) and higher in some cases. Metallurgical coal prices skyrocketed in a similar manner and the industry at long last appeared assured of an adequate return on investment. Many companies did expend large sums of money to upgrade and expand their mining and preparation facilities. Unfortunately the bubble eventually burst, in great measure due to the downturn in the US domestic steel industry and the resultant decline in metallurgical coal demand, loss of export markets to other nations and even imports of large amounts of foreign coal to the United States, and more stringent environmental regulations which made many high sulfur coal measures uneconomical to mine. Compounding the problem was the rapid world decline in oil prices in the mid-1980s which encouraged many consumers to utilize oil rather than coal. During the 1980s, metallurgical coal dropped over 20% in price, which, when considering inflation, actually amounted to about a 40% decrease in value. Export coal decreased a similar amount in price. Steam coal prices held nearly constant, thus also losing considerable value when inflation is considered. All of these factors make it even more imperative than ever that the industry do everything in its power to make wise economic decisions and to examine carefully all existing operations and planned future expenditures to be certain that their full cost implications are understood and that they can be justified on the basis of an adequate return on investment. It cannot be assumed that the price of coal will increase. To the contrary, as indicated previously, when considering inflation, coal decreased in value in the 1980s, just as it also did in the 1950s and 1960s. The price surges in the 1970s merely were a catchup game, and in truth the true market value of coal is in reality even lower than it was in 1950. CAPITAL AND OPERATING COST ESTIMATION Prior to constructing a new plant or expanding existing facilities, a detailed preliminary cost estimate is necessary to determine the capital investment

Jan 1, 1991

By Myron W. Mellor

Much has been published concerning the subject of coal preparation as related to electric power generation however it is always a most vital topic for both utilities and coal producers, It also constitutes a field of study that is never finished since new concepts and changing demands continually require altered perspectives. One graphic illustration that has been used to emphasize the rapidity with which times are changing is the fact that during World War I, a station that consumed 1000 tons per day was looked upon as a large central station, while today some single generators require 1500 tons during the same period, For further emphasis, at that time a 20,000 horsepower turbo-generator was a mighty large machine; today, a unit of this size is planned for driving the boiler water feed pump required for a single large main unit. During the past ten years alone, electric utilities have more than doubled their percentage of coal consumed as compared to the total market. They now account for approximately 40% of the United States consumption and one-third of all production including export, Conversely, approximately 70% of all U. S. steam electric generation is by coal and this percentage is expected to increase. It is further predicted that utility consumption will increase from the current 160,000,000 tons per year to between 400 and 500 million tons in 1975 which is approximately equal to todays total production

Jan 1, 1959

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

By Jerry M. Whiting, Landy A. Stinnett

The subject of this paper is broad and complex. Secondly, it is near and dear to the authors' hearts. Therefore, it doesn't seem possible to deal with every aspect of it in less space than a good size textbook. Also, if we dealt with all of the basics of feasibility studies and report preparation, we would cover a lot of material available in the literature, and would have to minimize our editorial comments. In view of these limiting realities, we have chosen to discuss selected facets of the subject, and to provide several comments which stem from our personal experiences during the past 20 years. "Think Ahead" hen someone is undergoing training to command a large ship, the following short phrase is engraved in his memory: "Think Ahead." The reason is simple enough. A battleship, aircraft carrier or oil tanker cannot change directions quickly, and if one waits to a what the other ship is going to do, there may be twisted metal and bodies scattered all over the ocean floor. The commanding officer has to use radar, forward rind aft lookouts, experience, common sense, intuition, weather forecasts, and everything else available to him to avoid trouble. Remember the USS Stark, and the fate of its captain? The fact the Stark was hit by a "friendly" missile didn't lessen the damage. How about running into a mine? Is it an excuse that no one thought about the possibility of a minefield ahead of the ship? The point is, relative to feasibility studies, that its prospective authors, and especially the commander of the efforts required to create it, must "think ahead" from the moment of their association with 4 mining activity. They must

Jan 1, 1987

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

By Zefang ChenLi, Laijun Ma, Lei Mao, Fang Lian

"In our work, the preparation technique of high pure manganese sulfate directly from low-grade rhodochrosite ore (MnCO3) was studied and improved intensively, including the effective leaching process and the short purifying process. Based on the same ion effect, the repeated leaching of rhodochrosite with sulfuric acid is proposed to improve the solubility of Mn2+ and inhibit the dissolution of the impurities Ca2+ and Mg2+. Moreover, the repeated leaching process could make full use of rhodochrosite and lower the dosage of sulfuric acidas raw material. With the aid of theoretical calculation, Ba(OH)2 was chose to adjust the pH value of manganese sulfate solution, and BaF2 to remove Ca2+ and Mg2+completely in the process of purifying. The results demonstrate that the extraction ratio and the recovery ratio of manganese reached 94.3% and 92.7%, respectively, which shows the prospect of industrial application. In manganese sulfate production, the heavy metal impurities have been decreased to less than 1ppm. Moreover, the content of calcium, magnesium and sodium has been decreased to less than 20ppm, which meets the standards of high pure reagent for energy and electronic materials. Our study enlightens an approach to the sustainable application of low-grade rhodochrosite.Introduction Low-grade manganese carbonate ores (=14%) becomes gradually the main resources for exploitation and applications in China according to national mineral resources survey (Tan et al 2004 and Singh et al 2017). Therefore, the electrolytic deposition technique of rhodochrosite faces great challenges including low electrolysis efficiency, high-resource input and high-pollution discharge (Fu et al 2010, Michelis et al 2009, Zhang et al 2013). Recently, more and more amount of manganese series with high or super high purity such as MnSO4, MnO2, Mn3O4 and MnO is demanded with the development of energy and electronic materials. Due to low-grade ores containing multiple elements such as iron, silicon, calcium and magnesium, conventional preparation of manganese sulphate with high purity from electrolytic product is characterized by long production-cycle and high-energy consumption (Subrat et al 2011, Mpho et al 2013). By contrast, hydrometallurgical method combined with thermal decomposition, hydrothermal synthesis and sol-gel processes has been widely studied because of its high efficiency, low consumption and low cost (Chen et al 2008). But the key problem in direct preparation of manganese series form low-grade rhodochrosite is to remove completely the multiple impurities such as iron, silicon, calcium and magnesium (Liu et al 2014). So it is urgent to develop a sustainable alternative approach with character of short process, high efficiency and environmental friendly."

Jan 1, 2017

By Arthur S. Maynard

There was a tendency several years ago for the average coal producer to more or less sit back satisfied with the big utility and metallurgical mar¬kets with long term contracts, not realizing, or possibly not evaluating correctly the importance of the growing industrial market Even the companies which were producing coal for the industrial market were primarily interested in the larger industrial customer, not fully realizing that a large percent of the industrial coal sold was to plants using less than 15,000 tons per year. As a result, possibly, the greatest inroad made by competitive fuel was made in this group. The situation mentioned previously cannot be blamed entirely on the fact that the coal markets were not evaluated in their proper perspective. Some of the responsibility would have to be due to the situation that existed during the last war' and the period immediately following, when most of the coal was put to markets of higher realization, leaving the relatively small -industrial user-to get his fuel wherever he could. This usually would mean coal from some 'gopher hole" with fluxuating quality and supply. Therefore, it was not uncommon for some industrial customers to go to competitive fuels as soon as equipment and fuel were available. Fortunately, before this situation got completely out of control, the coal producers, realizing the seriousness of the problem, made available, usually through their sales department, combustion engineers and other specialists, to help the industrial user with his problems; The engineers usually found several problems, old equipment, use of incorrect size con¬sist, ash and fusion coals, lack of automation, fly ash and dust problems which increased cost and jeopardized the customer's relations with his employees and the public.

Jan 1, 1959

By Ch. R. V. S. Nagesh, Ramesh Naidu Mandapati, Venkata Swamy Nalajala, Tondepu Subbaiah, Naga Jyothi Kothamasu

Leaching studies of magnesite obtained from Tamilnadu Magnesite Limited, Salem, have been carried out using hydrochloric acid leaching and percentage of magnesium chloride recovered was estimated. The variables considered in this study were the following: duration of leaching, volume percentage of hydrochloric acid, temperature, and pulp density. Percentage recovery of magnesium chloride increased with duration of the leaching, volume % of concentrated hydrochloric acid, and temperature. Percentage recovery of magnesium chloride decreased with increase of pulp density. The optimum conditions found to be pulp density (10%), hydrochloric acid concentration (30%), duration of leaching (2 h), and temperature (348.15 K). Iron was removed by treating the leach liquor with hydrogen peroxide and by raising the pH to 3.5–4. The purified leach liquor was subjected to spray drying for producing high pure magnesium chloride.

Jun 7, 2022

By M. S. Vernon, J. J. Kellar, W. M. Cross, R. M. Winter, F. J. Johnson, A. G. Pommer

Three substrates (MgO crystal, CaF2 crystal and Mg plate) were used to construct thin layers of Mg(OH)2. Various routes were used to modify these substrates, including surface hydration and sol-gel coating. In each case, it was found (by using Fourier transform infrared spectroscopy) that thin layers of Mg(OH)2 could be produced. In the case of hydrated layers, the surface morphology of the Mg(OH)2 resembles the bulk platelet shape of precipitated Mg(OH)2.

Jan 1, 2000

By James Yancik

The Howe Coal Company located in Leflore County, Oklahoma is mining the Oklahoma Lower Hartshorne Coal bed which ranges in thickness from 38" to 42" and dips approximately 7 degrees to the Northeast. The Lower Hartshorne bed lies within the Hartshorne sandstone in Oklahoma but is as much as 60 feet above this sandstone formation in Arkansas. This coal bed extends throughout the Arkansas Oklahoma coal basin, which is about 50 miles wide and 180 miles long and progresses from a semi anthracite in Arkansas to a low-volatile coal in the eastern part of the Oklahoma to a high-volatile coal in the western area. The Howe Mine #1 in the eastern area is mining a low-volatile bituminous coal which has been used as metallurgical coal since the early 1900's as evidence of Bee-hive coke ovens still remain near the town Howe, a few miles northwest of the mine site. The Howe Mine is the first mine in the area to use modern mining equipment, however, numerous punch mines have been worked along the outcrop south of the mine site dating from 1900 with the last closing in 1965. The coal characteristics of the Lower Hartshorne rival the Pocahontas seam in chemistry and coking qualities. This paper will be concerned with the preparation of the coal for the Japanese steel market. The three man crew necessary to operate the plant are the operator, the helper, and the equipment operator needed to feed the raw coal hopper. An additional equipment operator is available on the day shift for coal loading and moving the clean coal to the storage pile as the area under the clean coal belt is only large enough for 1 shifts production. We are at present running the plant on a 2 shift per day basis.

Jan 1, 1969

By C. I. Wilmot, A. Sass, J. VanDeBeuken

Introduction This chapter addresses the need for operation manuals, presents an outline as a guide for writing the manual, discusses who should write the manual, suggests how it is implemented and gives tips to potential manual writers. Theory & Purpose of Operating Manuals The primary objective of the operating manual is to provide every operator the benefit of a uniform minimum level of training. This training is not only critical to the safety and efficiency of every employee, but also provides a basis for incorporating future operational improvements into standard and emergency procedures. The manual promotes safety through- out and additionally has a special section devoted to safety. The operator should be able to find information on chemical and physical hazards as well as be exposed to safety procedures for such items as motor lockouts and tank entries. The operating manual will usually reference a separate safety manual or incorporate parts of the safety manual. Safety is also promoted through standardized procedures for operation of equipment. Standardized operation is the second most important reason for the writing of manuals. If equipment is started, operated, and shut down in a consistent manner, then operational efficiency should be maximized. If it is not, then the procedure is adjusted until it is. The experience of many can be condensed into set responses for start up, shutdown, steady state operations, and upsets. Implicit with the standardized operation objective is a minimum level of training the operator will receive by thorough familiarization with the manual. The ability to know the contents of the manual is a basic requirement for operator status. The operating manual serves as a basis for a training program both at the start of the new plant and as new operators are hired or promoted into the job. The operating manual is a collection of at least part of the knowledge that "key people" own and will cushion the loss of key personnel for whatever reason. The manual can only fulfill these lofty goals by being a dynamic document. Manuals must change as equipment is modified and superior techniques evolve. To be effective they must be periodically updated, so word processors and reproduction

Jan 1, 1986

By Karl S. Vorres

Coal my not seem like it, but it is a perishable commodity. The basic coal scientist cannot always replicate earlier experiments with a given sample because of changes that have taken place in the sample. This has led to a stated need for stable samples Coal looks like a uniform black solid to many people, but it does vary in its composition from state to state and mine to mine it also can be shown to vary significantly within a mine or seam. These variations have led to a stated need for consistent samples.

Jan 1, 1985

By Ahmed M. Yousif, Walid M. Abdellah, Galal M. Abdel Wahab, Amal E. Mubark

The present work is concerned with selective dissolution of niobium from Gabal El Faliq concentrate sample by using fluoridefree process. The chemical analysis of concentrate sample revealed the presence of high amount of ZrO2, Nb2O5, Re2O3, and HfO2 assaying 33.6, 1.99, 4.8, and 1.2%w/w respectively. Several economic minerals including zircon, samarskite, fergusonite, and xenotimewere recorded in the studied sample. About 98%of Nb content was selectively dissolved at the optimumconditions of 1:2 concentrate sample: KOH weight ratio, 2.5 h fusion time, and fusion temperature of 550 °C. Organic solvent extraction process using Aliquat 336S in xylene was effectively used for preparing pure Nb2O5 (98.95%).

Oct 22, 2019

By John Duff Erickson

Computer use has become an integral part of mine planning at Kennecott Copper Corporation?s Utah Copper Division, Bingham Canyon mine. Engineers are using the computer for development drilling calculations, mineralization grade interpolations, ore value summaries, long-range mining plans and short- range mining plans. The versatility of the computer has made it possible to explore many mining plan variations and to develop plans covering varying time intervals and production rates. This paper will summarize computer use in long-range mine planning, tell how short-range mining plans are prepared by conventional methods and discuss the development and application of short-range mine planning by computer.

Jan 1, 1966

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By Jae-Chun Lee, Kang-In Rhee, D. B. Dreisinger, Hyo-Shin Yu, G. A. Kordosky

The development of a process for direct synthesis of very pure ZnO powders from zinc-bearing waste was investigated. The zinc waste which contains 55% zinc was leached with sulfuric acid. After iron removal by hydrolysis from this zinc solution, purification through solvent extraction by the use of D2EHPA as an extractant was carried out. Then, loaded zinc in the organic solution was stripped and precipitated simultaneously using oxalic acid as a precipitant. Synthesized ZnC2O4 precursors by precipitation stripping were calcined to obtain ZnO powders exceeding 99.9% purity. The effects of sulfuric acid concentration, leaching time, and pulp density on the extraction of zinc were studied and optimum conditions for the solvent extraction were obtained through purification of the zinc solution. The size, morphology, and size distribution of synthesized ZnC204 powders were studied in terms of oxalic acid concentration, temperature, surfactant added, precipitation time, etc.

Jan 1, 1993

By S. Bhattacharjee, S. K. Singh, R. K. Galgali

A method for the preparation of zirconia- toughened mullite using dc plasma is presented. An indigenously developed 50-kW thermal plasma reactor is used for the preparation of zirconia-toughened mullite using a dissociated zircon and alumina mixture. Both XRD and SEM studies of the product confirmed the formation of mullite and zirconia. The zirconia grew as equiaxed grains of uniform size (~5 µm) in a mullite matrix.

Jan 1, 2002

By Mel J. Laurila

The application of on-line ash analyzers in coal processing has become widespread. However, the analyzers are employed largely in monitoring, blending or sorting applications. Just recently has work begun on using on-line ash, moisture and/or solids data for plant control; and even more recently for localized circuit or unit operation control. Process Technology, Inc. (PTI) has since 1990 placed several bulk coal and slurry analyzers in practice where Fuzzy Logic Control (FLC) loops are used to manipulate controllable variables in real time. This technology is now being advanced by PTI. Unit operations where FLC has been employed in feedback loops using on-line ash analyzers include: heavy media vessels, cyclones, concentrating tables and froth flotation. The design, implementation and improvements attainable in preparation plant control using on-line ash analyzers are outlined in this paper.

Jan 1, 1995

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969