Search Documents

By Ralph Bernstein

The processing of earth observation sensor data by digital technology is almost two decades old. Only recently, however, has this technology become practical and economical. The reasons for this are interesting to analyze, and they provide some insight into what the future may bring. Some of the earlier activities and their limitations, current systems and their applications, and future technology direction are summarized.

Jan 1, 1979

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By Arthur L. Raub

During the last decade, there haven't been any great innovations in the design features of a copper concentrator. What has worked well in the past continues to work well, so that major breakthroughs have been minimal. Conservatism in the ranks also plays an important part. As a copper concentrator is not designed and built everyday, Davy was elated to have an important part in this project. This is the story of the design of the oracle Ridge Project located north of Tucson on the back of Mt. Lemmon at an elevation of 5,900 feet on the N.E. slope of the Catalinas. The Oracle Ridge property, formerly known as the Control Mine, is owned by Oracle Ridge Mining Partners, a joint venture between Continental Materials Corp. of Chicago and Union Miniere of Brussels, Belgium; both or¬ganizations specializing in the non-ferrous metal industry.

Jan 1, 1979

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By Jan Jekielek

Increasing capacity of bulk material handling systems creates difficult problems for accurate in-line material weight measurements. At the same time increasing system complexity and growing user demands call for more measurements. Precision in-line weight measurements for bulk materials are usually accomplished by application of conveyor belt scales. Belt scale accuracies listed by scale vendors are applicable for ideal situations with suitable conveyor design, belt scale location and calibration means. This paper attempts to provide designers and users with simple means to evaluate belt scale accuracy for practical scale installations. Based on known mathematical models simplified formulas for measurement errors are derived and discussed. These formulas allow for simple determination of achievable accuracy for alternative scale installations on the conveyor, conveyor designs, etc.

Jan 1, 1979

By Raimo J. Leimala, Heimo U. A. Saarinen, Matti Seilo

Processes for hydrometallurgical treatment of crude nickel hydroxy carbonate and impure high grade ferronickel to produce cathode nickel and cobalt hydroxide are described. Outokumpu nickel refining process originally developed for nickel matte has been adapted to the mentioned new raw materials. Both new process routes contain the Outokumpu cobalt removal and nickel electrowinning stages but leaching and solution purification stages differ from the industrial process in operation in Harjavalta.

Jan 1, 1979

By G. E. McCormack

The Development of Water Gel Explosives Water gels are the most recent development in the evolution of commercial explosives. They are replacing dynamite, having proven themselves to be excellent alternatives to this standard explosive. Water gels have steadily displaced dynamite over the past two decades. In 1959, they accounted for only 1 percent of the market they share with dynamite. By 1965, the share taken by water gels had grown to 21 percent. In 1970, it was more than 40 percent, and today it is nearly 70 percent. Black powder, the first widely used explosive, revolutionized mining and quarrying in its day. However, when nitroglycerin dynamite became available about a century ago, it rapidly displaced black powder because it provided greater energy for a given weight, much higher velocity for better rock shattering performance, and water resistance for easy use in wet conditions. During the past 50 years, ammonium nitrate has played a dramatically increasing role in explosives. First, it was used as an ingredient in dynamite, and then as the main component in nitrocarbonitrate blasting agents. About a quarter of a century ago, it began to find use in a simple and inexpensive mixture with fuel oil that has revolutionized the explosives industry and today fills about 80 percent of the requirements for explosives in the U.S., and certainly the bulk of blasting requirements worldwide. Water gels and dynamites share the remaining 20 percent. Water gel explosives based on ammonium nitrate have also been developed during the past quarter century. These explosives contain

Jan 1, 1979

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By John A. Herbst

Mathematical models of mineral processing unit operations have been developed and used for a variety of purposes. Models, defined as equations which mathematically approximate the behavior of process units, are being employed in simulators to evaluate proposed flowsheets, to investigate flowsheet modifications, to study the effect of variables on circuit behavior, to optimize the performance of circuits off-line, and to compare alternate control strategies (Mular and Herbst, 1978). Models developed for mineral processing operations may be placed in one of two general categories: phenomenological (based on mechanism) and. empirical (based on experimental data only). Dynamic models (including time as a variable) .are useful for control studies, while steady-state models (independent of time) are employed in flowsheet evaluations. Phenomenological models are potentially more flexible and accurate than empirical models. However, models constructed from theoretical knowledge are less easily developed compared to empirical expressions fitted statistically to experimental data. The latter apply only over the range of data acquired. Most often, models used in practice are the result of a combination of theoretical and empirical approaches.

Jan 1, 1979

By Christopher Haycocks

Successful ground control is an essential part of all viable underground mining operations. To a large extent ground conditions influence the choice of mining methods, percentage and cost of extraction, and often the degree of safety that can be achieved. Utilizing the computer for ground-control planning offers great potential under many diverse conditions as not only are computations facilitated, but also details of the often complex geologic and structural framework of the mine can be readily stored and retrieved. Two basic approaches have been developed for applying the computer in solving ground-control problems. The first uses an analytical method, such as the finite element technique, for solving a specific problem. The second is more general and involves storage of geologic data and application of general design equations. The latter has found wide application in stratified deposits. It is the purpose of this chapter to describe both approaches as they are used for improving the ground-control aspects of mine planning.

Jan 1, 1979

By Thomas F. Martin

Contract 75-124-211 extends along the Chicago River from Roosevelt Road on the south to Ogden Avenue on the north. In addition a branch tunnel runs east from approximately mid-project ending near Lake Michigan. The contract was bid on December 14, 1977 with three joint-ventures submitting bids. Of these the joint venture of J.F. Shea Co., Inc. Walnut, California, (Sponsor), Peter Kiewit Sons' Co., Omaha, Nebraska and Shea Company and Associates, Walnut, California was low with a bid of $101,976,680.00. The MSD awarded the job to the Joint-Venture on January 5, 1978 with a scheduled completion date of January 23, 1983. The project consists of the following major items of work: (1.) A 25'-0" minimum diameter Construction Shaft, 220 feet deep (2.) 13,726 Linear Feet of 30'-0" Concrete lined Tunnel in rock (3.) 6,648 Linear Feet of 13'-0" Concrete lined Tunnel in rock (4.) Seventeen concrete lined Drop Shafts varying in finished diameter from 4'-0" to 12'-0", and each approximately 250 feet deep with chambers and connections to the tunnels varying from 100 to 1300 feet in length.

Jan 1, 1979

By David H. Carlson

The paper presents background information including data on diesel exhaust pollutants, amounts produced and standards, a desscription of mine characteristics that affect air monitoring techniques and a review of portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the Experimental Mine, the diesel dilution tunnel test cell, the Mine Air Monitoring Lab (MAML), the portable instruments and the production mines used.

Jan 1, 1979

By Ian McFeat-Smith, Robert J. Fowell

Roadheader machines have a specific place in modern tunnelling, not simply as a compromise between drill and blast techniques and full face machines, but as an economic and versatile form of mechanised tunnelling where the method of excavation is easily integrated with tunnelling operations. In the past, roadheaders have been subjected to misuses by engineers who failed to realise that, as in all mechanised tunnelling, a planned and systematic approach is essential if the full potential of these machines is to be gained. An increasing awareness of this, together with the introduction of the more powerful roadheader carrying their cutting potential into the hard range of rock is changing this situation and now makes the prospect of using roadheaders particularly attractive (1). The advantages gained by employing these machines can be considerable and Table 1 lists some of them. This table illustrates that from both cost, and installation points of view, the roadheader has considerable benefits over the full face machine. However, the principal advantage gained is in broken ground where heavy supports can be installed immediately at the tunnel face. In addition, access for planned maintenance and repairs to most working parts of the machine is at a premium and average machine utilisations of 40 - 60% can be expected. In comparison to drill and blast methods, up to 40% better progress can be regularly achieved, and the subsequent savings in overbreak costs alone would more than pay for the cost of a roadheader used to drive a 3km long tunnel. As with full face machines, ground disturbance is minimal and for short tunnels in urban areas a road-

Jan 1, 1979

By Karen M. Kessen

The isotopic variations of lead from Mississippi Valley galenas have long been used to place constraints on the sources of the lead, and on the residence the of the lead in crustal reservoirs prior to its emplacement in the Mississippi Valley province. Similar studies based on strontium isotope variations in gangue minerals associated with the lead-zinc sulphides have been neglected until Haden's (1) study of such minerals from several localities in northwestern Ohio. His work revealed two things about the mineralization. Firstly, it shoved that the average isotope composition of lead from galenas from northwestern Ohio lies on the anamalous lead line characterizing Mississippi Valley-type leads, albeit at the least radiogenic end of the entire data array. This confirm earlier assignments of the Ohio mineralization as Mississippi Valley-type (Hey1 and others (2)). Secondly, Haden (I) showed that the strontium in the calcite, strontianite and fluorite is broadly similar in isotopic composition to the strontium in the host Silurian to Devonian marine carbonates within which these minerals arc emplaced. He concluded that the mineral strontium my have been very locally derived, from the carbonate hosts.

Jan 1, 1979

By T. A. McAfoose

As one of the major suppliers of the chestnut Ridge energy center, Rochester and Pittsburgh Coal Company continues the search for more efficient haulage systems. This search is one that is essential in providing coal to the Keystone and Homer City power plants at the most economical cost. These two electrical generating plants located in west central Pennsylvania are part of the energy center which consists of four generating stations. Prior to the time the two stations were put on line, August, 1967 for Keystone and August, 1969 for Homer City, our company made the decision to rely on belt conveyors from the section to the surface to provide for continuous main line haulage. The proximity of these generating stations to proven reserves allow for minimal truck haulage and minemouth setups. With the addition of seven new mines, in the past ten years, revisions have been made on the original setup to interconnect the haulage of several mines to deliver the product by belt to the power plants.

Jan 1, 1979

By Dale K. Fields

With today's technological advances in mineral processing equipment, there is an increasing demand for accurate system control. This can only come about through representative sampling. The purpose of this paper is to guide you in the selection of sampling equipment and outline design parameters for the cutters used in dry and wet sampling without adding redundant mathematical probability formulas to your files. Special attention will also be given to the equipment used in conjunction with samplers and sampling systems, such as feeders, crushers, chutes, launders, and controls.

Jan 1, 1979

By Hans Skretting, Abraham A. Dor

This paper briefly reviews the historical development of the Rotary Kiln-Electric Furnace Process, which was first applied commercially to the treatment of qarnieritic ores in New Caledonia in the mid-fifties. It describes various technological improvements introduced, since, in industrial plants or developed in pilot facilities where a wide variety of nickel oxide ores has been treated success- fully over the years. Major categories of ores are characterized. The effect of their physical and chemical properties on their performance in the electric furnace is discussed. The relationships between ore composition, ferronickel grade and slag composition are analyzed and their effect on slag and metal tapping temperatures, nickel recovery, and electrode voltage are discussed.

Jan 1, 1979

By Ignacio Salazar

Somebody sure gave me the wrong title. I can talk much more freely about the impact of the anti-nuclear movement on the DRILLING industry in New Mexico. In a word, it is being "clobbered." It doesn't seem like very long ago that my brothers and I were busy trying to find enough new equipment (and trying to talk bankers into lending us enough money) to keep up with drilling work we could get. Seemed like no matter how hard we worked, and how much money we borrowed, we were always one step behind where we wanted to be. We had so many holes to drill that all our crews were working three shifts a day, and over several states. The nation needed energy, and we were ready to help supply it. Exploration and development drilling jobs were all going full-blast. We had trouble keeping up with them. With luck, we figured we'd be able to get all our equipment out of hock before all the necessary uranium mines were developed.

Jan 1, 1979

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979