Search Documents

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By J. E. Carr

A bewildering number of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General types are: 1. Conventional Thickeners (Fig. 1). 2. Thickeners with Flocculating Feedwells (Fig. 2). 3. Solids Contactors (Fig. 2). 4. Tray Thickeners (Fig. 3). 5. Lamellas (Fig. 4). 6. Conventional Thickeners with Lamellas 7. High Flow, Fluid Bed Thickeners (Fig. 5). These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these are listed: 1. Feed velocities must be limited and/or controlled. 2. Natural or reagent flocculation is necessary. 3. Horizontal settling area is the basis for capacity. 4. Overflow velocities must be limited and/or controlled. 5. A controlled underflow is necessary. Applying these needs to the basic process concepts is thickener selection. The basic function of a thickener in the minerals industry is the separation of a thickened sludge containing fine solids from water. To this primary separation function are frequently added others to give a list as follows:

Jan 1, 1977

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By Sam H. Patterson

This paper is concerned primarily with the kaolin deposits extending northwestward from Macon, Ga., which is in the western part of the Irwinton district (fig. 1). These deposits are in a belt of kaolin districts extending along the inner edge of the Coastal Plain from the Aiken district, S. C., southwestward to the vicinity of Macon, a distance of 150 miles (250 km). Large kaolin deposits associated with bauxite also occur in an extension of this belt southwestward from Macon as far as the Eufaula district, Ala., a distance of about 130 miles (208 km). The belt splits away from the inner edge of the Coastal Plain in a southwesterly direction from Macon; the Eufaula district is approximately 50 miles (80 km) south of the contact of Coastal Plain sedimentary rocks with much older crystalline rocks. Structure The strata of Cretaceous and Tertiary age containing the kaolin deposits all dip gently seaward irom the landward edge of the sedimentary rocks. The dip of the Cretaceous strata is about 25 feet per mile (4.9 m per km). The dip of Tertiary strata is about 15 feet per mile (2.1 m per km). In places, the Tertiary strata overlap the older sedimentary beds and rest directly on the crystalline rocks. Faults having a few feet of displacement have been observed in several mines, but no major faulting is known in the area.

Jan 1, 1977

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I'm not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I'm using the term "battle" loosely because, in reality, it wasn't a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I'd like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government's harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

By John W. Wilson

Every operation connected with the working of a deep-level mine has, to a greater or lesser extent, a direct bearing on the costs of production, and hence, profitability of the mine. If adequate mine planning is not done in the early stages in the life of a mine, considerable expenditure can result from the cost of maintaining mine service tunnels, production delays in stopes caused by poor strata control, distortion of fittings in hoisting shafts, rockbursts and so on. In fact, the optimum profitability of a deep-level, hard-rock mine can only be achieved if the layout of the shaft systems, ore passes, tunnels, stoping areas and other underground excavations are designed to withstand or accommodate the rock stress conditions that will be created by mining operations. In South Africa where the deepest mines in the world are located, access to the underground workings of most deep-level gold mines is via vertical shaft systems and a network of tunnels connecting the shaft systems to the stoping areas. In current practice, there are two basic methods of extracting the gold-bearing reef,* namely, the scattered stoping method and the longwall stoping method. The choice of the stoping method is governed largely by the anticipated gold distribution and payability of the reef in the area, the geological conditions, the degree and complexity of faulting and dyke intrusions, the depth at which the gold-bearing reef is to be mined and the inclination and width of the reef. The longwall system was first introduced at the East 717 Rand Proprietary Mines Limited in 1942 in an effort to combat the rockburst hazard which appeared to increase with increase in depth. This mining method became standard practice on that mine for stoping operations 700 ft. below the surface. Since that date, several deep mines on the Central Rand, East Rand and West Wits gold mining areas have adopted this method.

Jan 1, 1977

By William J. Dimond

Computor analysis has opened a new world of information for the mining of resources. This paper is directed at the mining of coal. The same procedures apply to most mining projects. The available facts when evaluated against the variables produce the answers. The project must be carefully analyzed, so that the facts can be organized in a data file. The file can be expanded as additional information is obtained during the entire life of the mine. If the mine is pre-planned, the file will be expanded in an orderly fashion and updated information will be available at all times. The development of a property goes through several phases; Exploration, Economic Analysis, Development, Production, and Reclamation. Each phase is an expansion of the data file. The validity of the answers is directly related to the accuracy and quantity of available data. The basis for a data file is horizontal position, and elevation of each piece of information. A coordinate system and datum are reference for a digital (X, Y and Z) position in a spatial system, a three dimensional digital model of the mine. The current practice is to use the State Plane Coordinate system and elevations as established by the U. S. Coast and Geodetic Survey. Each state has adopted this system by law. In the event there is litigation, it is an advantage to have the data on the legally recognized system. The control must be expanded so that all data can be assigned a digital position, and planned to fulfill the requirements for all phases of the mining operation. The project must be analyzed to insure that the objectives can be achieved without duplication or loss of time. sufficient data must be available to reach each required level of information. The coal data can be defined in two categories, spatial

Jan 1, 1977

By Daniel A. Jones

The Surface Mining Control and Reclamation Act of 1977 establishes a nation-wide program requiring the Secretary of the Interior, through the Office of Surface Mining Reclamation and Enforcement, and the States to protect against the adverse effects of coal mining and to reclaim previously mined lands left without adequate reclamation. The Act requires coal mine operators to: restore the land to approximate original contour, return the land to a condition capable of supporting prior potential uses, protect the hydrologic balance, segregate and restore topsoil, control blasting to prevent damage and injury, establish vegetative cover, and control surface effects of underground mining. The Act also establishes: a reclamation fee on coal, a program to assist small operators, a program to give technical and financial assistance to State programs, State Mining and Mineral Research Institutes., a program for designating areas as unsuitable for mining, and a study on surface mining of minerals other than coal.

Jan 1, 1977

By H. A. von Schonfeldt, H. Douglas Dahl

INTRODUCTION During the past decade, significant pro¬gress has been made in applying rock mechanics principles to mine design problems by a great number of researchers. Some of these new techniques have found their way into the engineering and planning offices of the operating mine. In spite of these advances, however, the application of rock mechanics in the day-to-day mine planning and design of our domestic coal mines is rela¬tively rare. There are a number of reasons responsi¬ble for this relatively slow progress, not the least of which is the question of how to measure the success or cost effectiveness of a sizable rock mechanics effort in an opera¬ting mine. Firstly, the properties of geologic materials generally vary over a wide range and it is, therefore, difficult to assess whether an improvement in the mining conditions is due to a design change or due to a change in the geologic conditions. A second reason for the slow acceptance of rock mechanics in engineering thinking is the fact that some of the concepts are quite difficult and that physical evidence of their validity to mine design is still rare. Thirdly, com¬munication between research, engineering and applications oriented people appears to function only intermittently. In our view, however, the most important impediment lies in the "state-of-the-art." Exactly how much can rock mechanics help the mine operator? The best that rock mechanics can do at present is determine whether one approach is better than another when weighed against some design objective (stress, strain, deformation). We cannot determine the abso¬lute best ground control design -- only what is better. If ground control is lost, the statement that "it's the best one we looked at" means very little to the harried operator. While the "state-of-the art" has advanced a great deal, it has certainly not been reduced to an engineering matter in that design hand¬books are available -- they are not. The success of a rock mechanics program, there¬fore, can be determined only over a long period of time of continuous effort.

Jan 1, 1977

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

By John W. Graham

To start my talk, I thought it might be helpful for us to define the term "aggregate", so I went to the dictionary. Webster has several listings under "aggregate", and I found the following: "1. A mass or body of units or parts somewhat loosely associated with one another." Well, I didn't like that term "loosely" so I read on. "2. Crystals of one or more kinds of mineral or rock fragments." That sounded better, but I still read on. "3. Any of several hard inert materials used for mixing with a cementing material to form concrete or mortar." That sounded even better, but it should be a little broader. So I would like to define "aggregates" for you as follows: "Hard, inert fragments of rock or minerals used alone or with cementing agents to form products essential to nearly all types of construction." Usually aggregates are sand, gravel, or crushed stone, but other minerals such as clay or shale can be heated and become aggregates. What are some of the construction uses? Well, we've already mentioned concrete, as used in streets and highways, sidewalks and parking lots, airports and all kinds of building construction, not to mention bridges and swimming pools, and docks and breakwaters, just to list some of the uses. Our way of life couldn't exist without concrete. And you can't have concrete without aggregates,

Jan 1, 1977

By T. D. MacQueen

Thank you Mr. Stevens. It's a pleasure for me to be speaking to this meeting of the Society of Mining Engineers of AIME this afternoon, and the Gypsum, Association is grateful for the invitation. A brief word about who we are: the Gypsum Association is the trade association for the gypsum industry - the manufacturers of gypsum board and lath a-d plaster. We have a membership of eight companies. These eight companies produce about 90% of the gypsum products manufactured in the United States ... closer to 94% actually. Our headquarters is in Evanston, Illinois. We have an east coast office in Washington, D.C. where the eastern manager handles technical and building code matters and maintains liaison between all of the government agencies and departments and our industry. We also have a west coast office in Los Angeles where our west coast representatives is heavily involved with the Uniform Building Code and ICBO. And then in the Evanston office our manager of technical and building code services, Herb Carlsen, bites his nails and loses his hair over these problems and various other projects that come in, such as conversion to metric and various other things. We also have a research associate at the National Bureau of Standards in Washington who is currently concentrating his efforts on the combustibility of building materials. His studies involve current testing methods, definitions, data analysis, and proposed new testing methods,.' It is anticipated that this program will lead to a better understanding of non-combustibility of building materials and systems. I mentioned that our members represent over 90% of gypsum products,' manufactured in the United States; it might be well to point out a couple of statistics about what that really means. According to the Bureau of Mines,

Jan 1, 1977

By Frank W. Reinrniller

Mill ball charging systems have undergone little change during the past two decades. Most operations utilize a locomotive/ball car combination to load and haul charges from the ball storage bin to the mill charging boxes or, alternatively, transport charges to the charging boxes by means of a ball bucket handled by bridge crane. This paper describes a new concept in ball handling systems that is in operation at the Island Copper Concentrator of Utah Mines, Ltd. at Port Hardy, B.C. This system employs a narrow belt conveyor to convey a weighed charge to each of nine belt unloading stations at the mills. In operation, the system has proved to be practicable, trouble-free and economical of operating labor.

Jan 1, 1977

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By James B. Cathcart

Marine phosphorite deposits occur in Brazil, in the Bambui Group of late Precambrian or Early Cambrian age. The phosphorite is laminated, isoclinally folded, and is composed of black, elongated apatite pellets and quartz grains cemented by quartz and muscovite. Abundant, narrow quartz veinlets cut through the rock at right angles to the elongation direction of the pellets. The phosphorite is 0 to 80 meters thick and contains 5 to 30 percent P205. The deposit is elongate towards the northeast, and the central, thickest, and richest part is bounded by faults. Measured reserves are about 250 million tonnes that average about 13 percent P205. Preliminary testing indicates that grinding, scrubbing, and desliming will produce a material usable for fertilizer manufacture at a cost competitive with imported phosphate fertilizers.

Jan 1, 1977