Search Documents

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By Taghi Sherizadeh, KUTAY E. KARADENIZ, Dogukan Guner, Samuel Nowak

Underground mining environments bring with them occupational health and safety issues with some severe dangers, such as mine explosions. During such events, miners may escape using main access openings or find a safe haven like a refuge alternative (RA) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is detailed, depending on conditions and abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification of resistance to explosion is discussed in particular, and studies in the literature are examined in terms of structural deformation.

Mar 1, 2023

By AJIT SWAIN, SUNATI MOHANTY

The ability to predict the dewatering performance of an industrial hydrocyclone from a laboratory-model hydrocyclone is of great importance. In this study, laboratory-scale hydrocyclone experiments were conducted using silica sand samples at 10 percent solid concentration for dewatering with Mozley hydrocyclones with diameters of 2 in. and 4 in. The objective is to predict the design parameters for an industrial dewatering cyclone to achieve higher solid concentration in the underflow. A model was developed based on the Nageswararao hydrocyclone model with the help of a commercial simulator for a hydrocyclone operating at 100 t/h and 20 percent solid concentration to achieve 80 percent solid recovery at 45 percent solid concentration in the underflow.

Mar 1, 2023

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By JOHN HOMER, KATHLEEN STABRYLA, JACOB L. CARR, JONATHAN K. HRICA, JENNICA L. BELLANCA

Given the recent focus on powered haulage incidents within the U.S. mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the research literature is timely. This paper aims to evaluate the maturity of CXS technology through the application of a technology readiness assessment (TRA) to research literature identified by systematic search methods. Results indicate that much of the evidence for CXS performance is at lower levels of maturity: that is, components and prototypes tested in a laboratory and in relevant environments. Less evidence exists for CXS performance at higher levels of maturity — that is, systems evaluated within operational environments — despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for more peer-reviewed research to evaluate CXS technologies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions, which contrasts with haul truck fatal accident statistics that indicate most are due to vehicle-to-environment interactions, such as traveling through a berm. Lastly, the relatively small number and segmented nature of relevant studies suggest there is a need for more incremental research that would better facilitate the improvement of CXS technologies. This progression could be achieved through continued long-term interest and support for CXS technology research.

Mar 1, 2023

By STEVEN J. SCHATZEL, Zoheir Khademian, KAYODE M. AJAYI

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine, creating safety concerns. To provide recommendations for developing guidelines that ensure a safe coexistence of longwall mining and unconventional shale gas production, this study uses a discrete fracture network (DFN) model to evaluate the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements.

Mar 1, 2023

By Smart Chika Obiora, Anthony Chukwu

Mining and processing of raw materials is one of the earliest activities of man for survival and development. The products are used for making jewelleries, metal tools, and for exchange of goods and services. However, despite the benefits of mine recoveries, it’s negative and long term effects on the environment and lives remain the point of discussion throughout the world. This study summarizes findings of researches in active/abandoned lead–zinc mines in Enyigba and Ishiagu mining districts including social surveys in the localities surrounding the mines in order to ascertain the effects on the inhabitants. Lead–zinc mining in Enyigba and Ishiagu, southeastern Nigeria has lasted for decades and has affected the socio-economic well-being of the host communities. There are evidences of soil, water, and plants contamination by Pb, Zn, Cd, and Mn in these mining communities. The mining activities also affect the overall social development of the host communities. These effects include retardation in educational development, health care provision, unemployment, and access to potable water supply. Others are rise in poverty level, social amenities, sanitary/hygiene level, high cost of living, and fertility rate. Possible mitigation strategies such as to liaising with relevant government agencies in collaboration with mine owner, mine workers, and host communities can ameliorate these negative effects and promote environmental sustainability.

Feb 24, 2023

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

By Weijian Yu, Jianbiao Bai, Jinlin Xin, Shiqiang Xu, Shuai Yan, Zizheng Zhang, Hai Wu

The retained roadway subjected to dynamic loading from thick and hard roof (THF) fracturing caused severe deformations in the thick coal seam (TCS). Understanding the dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF is the first step in determining the stability of the retained roadway. Characteristics of dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF are investigated through numerical simulation and field test of 150208 haulage gate in Sucun coal mine. To improve the reliability of numerical simulation, the double-yield model is used to simulate gob and the strain-softening model is used to simulate filling body; the dynamic module in FLAC3D is used to simulate the dynamic loading due to the THF fracture, and the global model are validated. Characteristics of surrounding rock convergence, plastic zone distribution, and vertical stress in the filling body after the THF fracture are reveled with respect to width to height ratio (W/H) of the filling body and the dynamic loading strength of the THF. The rational width to height ration of the filling body constructed with high-water materials is 0.57. Field monitoring results show that the GER with THF in Sucun coal mine could adapt the dynamic loading due to the THF fracture and meet the requirement. This study is helpful to better study the stability of GER according to the breaking dynamic load of THF and provides reference and guidance for the analysis of breaking dynamic load of THF under similar geological conditions.

Feb 23, 2023

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Seals and build-in-place (BIP) refuge alternatives (RAs) are two main underground structures to isolate an area from the active working zones with different purposes. While seals are used to prevent methane gas that seeps from coal seams and blast pressures from a possible detonation of the contained gas, RAs are used to provide a safe haven for miners who are unable to escape their working locations after an accident like an explosion or fire. The recommended BIP RA designs can be similar to seals constructed with steel-reinforced concrete. Both seal and BIP RA are constructed in different locations of the mines for a period of time, exposed to a certain convergence due to stress redistribution which can change their responses during an explosion. In this study, a steel-reinforced concrete wall to be used in such applications is simulated to examine the structural performance during an explosion for a coal mine model with different strata conditions using dynamic analysis by a 3D distinct element method (DEM) code. The main purpose of this study is to reveal any possible effects or trends on the wall deformation with changes in strata conditions by implementing different combinations of roof, seam, and floor material properties. The model is calibrated by the experiment conducted on a steel-reinforced concrete wall by the NIOSH researchers in the Lake Lynn Experimental Mine. The results show that strong adjacent rock and coal units are the least favorable condition for the survival of the wall subjected to a simulated explosion pressure. The results indicate that changes in the roof and seam conditions can have dramatic effects on the deformation characteristics of the wall when compared to the floor conditions. The results of this study might be enlightening for future BIP RA and seal applications.

Feb 8, 2023

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By Manoj Khandelwal, Jian Zhou, Yingui Qiu, Peixi Yang, Pingan Peng

Rockburst prediction is crucial in deep hard rock mines and tunnels to make safer working conditions. Due to the complex interaction of many factors involved in rockburst prediction, such as multi-variable and multi-interference factors, three hybrid support vector machine (SVM) models optimized by particle swarm optimization (PSO), Harris hawk optimization (HHO), and moth flame optimization (MFO) are proposed to predict rockburst hazard level (RHL). The RHL is determined according to four kinds of microseismic characteristic parameters including angular frequency ratio, total energy, apparent stress, and convexity radius. Then, six types of microseismic characteristic parameters are taken as input variables in 343 sets of data, including angular frequency ratio and total energy, etc.. And the RHL is taken as the output target of rockburst prediction. The classification performance of PSO-SVM, HHO-SVM, and MFO-SVM hybrid models is evaluated by accuracy (ACC), precision (PRE), and kappa coefficient. Findings reveal that the MFO-SVM model performs best in terms of accuracy, with ACC, PRE, and kappa coefficients reaching 0.9559, 0.9063, and 0.9094 respectively, while PSO-SVM and HHO-SVM have similar performances. However, the PSO-SVM, HHO-SVM, and MFO-SVM all perform better than the unoptimized SVM model. This confirms that the three optimization algorithms significantly enhance the rockburst prediction capacity of the SVM model to help mine practitioners apply machine learning methods to rockburst prediction problems appropriately.

Feb 3, 2023

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By M. Sandin

According to the world bank1, the mining industry consumes up to 11 percent of global energy use. In comparison, 70 percent of mining projects from the six largest mining companies operate in water-stressed regions. To steer the direction of the process industries toward more sustainable practices, more than 40 governments have adopted a price on carbon. This measure includes additional taxes on the use of fossil fuels, trade programs, new standards for renewable energy, energy efficiency mandates, more stringent emissions regulation, carbon offsets, etc. This emphasis is also supported by investors shifting their priorities to reduce risk by focusing on long-term plans, including environmentally friendly operations. The metals and mining industry is at the core of the green energy mix and electrification of vehicles. This new trend creates an astronomical increase in demand for minerals. Under a 2-degree scenario, according to the latest analysis from the world bank, as new energy technologies continue to grow, it is expected that all minerals to double in demand, and the distribution of these materials will depend on their application. • Solar panels, will account for 87% of the aluminum demand, and more than 95% of silver • Wind turbines and geothermal plants will require 98% zinc and 64% titanium. • Solar and wind energy alone will demand more than 74% of the global supply of copper, and this is without considering wiring or other infrastructure to connect the grid • Battery storage accounts for 100% of the graphite and lithium demand. (Hund, 2020) • Other materials, such as nickel and steel, are also projected to more than double in demand as they are cross-technology minerals. These materials require a manufacturing process that is accountable for the emissions proper of the transformation process. It requires that these processes move from a hindsight mode focused on reporting to a forecasting mode based on run-time measurement of GHG emissions. This is a critical first step in companies realizing an economic return for doing the right thing for the environment and their communities.

Feb 1, 2023

By C. Brown, N. Rayyan, T. H. Dubaniewicz

Lithium-Ion batteries (LIBs) have the potential to go into thermal runaway which introduces a new ignition source in hazardous environments such as gassy underground mines that may contain methane in the surrounding air. Researchers from the National Institute for Occupational Safety and Health (NIOSH) used an accelerating rate calorimeter (ARC) to induce thermal runaway in individual lithium-titanium-oxide (LTO) and lithium-nickel-cobalt-aluminum-oxide (NCA) LIB cells within a sealed enclosure with either no methane, a lean, a stoichiometric, or a rich methane-air mixture in the surrounding canister to determine if these LIB types would ignite the methane, causing an additive effect on overpressures. Canister pressures and maximum temperatures reached by the cells, surrounding air, and exhausted gases were measured in this study and remained consistent with varying methane concentrations.

Feb 1, 2023

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023