Search Documents

By M. A. Cristovici

The use of surfactants as wetting agents to suppress sulfide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulfide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactant adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1992

By S. R. Titley

Results of regional analyses of precious metal habits in Arizona ores lead to interpretations of a fundamental ore control related to geographic location that corresponds with crustal contrasts. Measurements of isotopic and trace element characteristics of Laramide ore-related intrusions lead to interpretations of crustal derivation of apparent ore-related magmas. Interpreted regionally, the numerous kinds of Laramide ores, which include porphyry copper deposits of this southern cordilleran region appear to be phenomena of a specific crustal lithology characterized by a basement of Proterozoic turbidites and (an interpreted) lower crust of amphibolite. This association with a specific basement terrane may be extended in principle from the United states into Mexico where faulted offsets of this basement are similarly favorable to formation of Laramide porphyry ores -to the exclusion of adjacent terranes. Whereas plate tectonic mechanisms may have triggered evolution of these ores, it is hypothesized here that crustal setting and crustal composition are more profound influences of metallogenesis.

Jan 1, 1992

By J. G. Groppo, J. G. Justice, B. K. Parekh

Removal of particulates and/or metal ions from mineral/coal processing waste water is a necessity from the environmental point of view. This paper describes application of a novel AC- electrocoagulation technique to remove the particulates as well as metal ions using AC power. A series of laboratory tests conducted on a stable black water sample obtained from a sub-bitminous coal operation provided a clear supernatant (-10 NTU) from the suspension. The process also shows promise in removal of up to 90 percent of phosphate ions and other metal ions (copper and nickel) from solution. A preliminary economic evaluation of the process will also be included.

Jan 1, 1992

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992

By A. Knoll, J. W. Beck, W. C. Brice, E. K. Lehmann

A cooperative study was undertaken in a neutral atmosphere by representatives of the environmental community, the mining industry and state government to identify and resolve environmental issues associated with base and precious metal mining before a commercial mining development is announced. The study included testing Minnesota's as-yet-untried nonferrous mining regulatory program using three hypothetical mining developments sited in environmentally sensitive areas where future mining could occur. Results include identification of critical paths for regulatory decision making, identification of particularly sensitive environmental issues that mill need continued deliberation before resolution and characterization of data necessary for environmental review and permitting decisions.

Jan 1, 1992

By B. M. Davis, J. Wilkins

The method of conditional simulation is easily implemented on the personal computer when the LU decomposition algorithm of Davis (1987) is employed. This algorithm is fairly compact, yet can generate moderate-sized simulations in a few minutes on a 80286 or 80386-based personal computer. The application of conditional simulation presented here is to generate possible ore inventories from a limited amount of exploration sampling. The simulations can then he examined to decide if the potential inventories are sufficiently attractive to proceed with further exploration. An example showing one application of this approach is presented.

Jan 1, 1992

By K. Cothern, S. Novack, D. A. Johnson, R. Borden, S. Pavlou

A procedure is presented for ranking hazardous waste sites for remedial decisions, and an example with application to mining waste sites is discussed. Typical contaminant concentrations are calculated from field data. Exposure indices that compare these measured concentrations with allowable limits are then computed. The limits are selected to protect both the health of humans (for both carcinogen and noncarcinogen effects) and the health of key organisms in the ecological food web. The additive exposure index for a site, defined as the sum of all contaminant-specific exposure indices, is then used in ranking the sites and assigning each a priority for remedial action. One key source of uncertainty in the process is the estimation of a typical site concentration from data that include values reported as "below certified reporting limit" (BCRL). This uncertainty is compounded in the additive exposure index and therefore may have a substantial effect on the assignment of remediation priority. A general approach is presented for incorporating consideration of BCRL data into uncertainty evaluation when assigning remediation priority designators to hazardous waste sites.

Jan 1, 1992

By Donald P. Spitzer, Peter V. Avotins

The flow properties of thickener underflow slurries can be characterized by their rheological parameters. Most of these slurries exhibit Bingham plastic behavior, characterized by a yield stress, to, and a Bingham viscosity, nB. Red mud is generated as a leach residue in the Bayer process. The use of new Bayer process flocculants which contain hydroxamate functional groups leads to muds which are qua1itatively considerably more fluid than muds generated with conventional polyacrylates or acrylatefamide copolymers. A variety of rheological tests confirm lower yield stresses and less extended floc structures with the new flocculants, at the same solids levels. Conversely, under given viscosity restraints, the new polymers make it possible to operate at higher solids levels, which offers major benefits in processing red muds.

Jan 1, 1992

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By E. Marques Coelho

Cationic flotation of quartz is currently utilized in the concentration of iron ores and the cleaning of phosphate concentrates. The present work deals with depression of quartz in the presence of aluminum aqueous species during cationic flotation. It was established that aluminum species depress the flotation of quartz with an amine, especially under neutral and slightly alkaline conditions. With an amine as the collector, studies of the adsorption (abstraction) of Al species on quartz surfaces, as a function of pH, correlated well with the depression of this mineral. The presence of Al species also enhanced the depressant action of corn starch on quartz. In addition, the sodium salt of ethylenediaminotetraacetic (EDTA) was found to be an effective complexing agent to suppress the depression caused by aluminum ions.

Jan 1, 1992

By T. R. Raponi, D. Barnes

The Williams Mine mines and mills 6000 t/d (6600 stp’d) of gold ore using SAG/ball milling, leaching and CIP, electrowinning and refining. Electrowinning, high-pressure cathode washing, filtering, retorting and refining are based around the use of knitted stainless steel mesh cathodes. Their primary advantage over conventional steel wool cathodes is that electrowon gold can be washed off and the cathode can then be reused. Typically, the knitted cathodes have a useful life of up to 15 months. Gold production of up to15 t/month (50,000 oz/month) is easily processed with this system. Presented is a description of this operation, including a review of the equipment and performance data.

Jan 1, 1992

By G. A. Rowell, T. M. Barczak, J. C. Zelanko

The US Bureau of Mines conducted a multifaceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps because the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements and microseismic monitoring, as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading and microseismic activity were monitored prior to, during and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and following the face bump. Shield load data, evaluated in an effort to identify trends that could be used to forecast coal bumps, appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source-location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1992

By D. Park, V. Gall

The three-dimensional finite element technique combined with a progressive failure approach were used to simulate stress distributions in a complete mine section that occur in response to a longwall mining operation. Due to the availability of a Cray supercomputer, a large-scale, three-dimensional, finite-element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1992

By J. E. Garlanger, R. K. Shrestha

During mining, the surficial aquifer and, in some cases, the top of the uppermost confining unit within the mined areas are excavated. Portions are removed from the area for resource recovery. Until the mined areas are reclaimed, the surrounding unmined area continues to dewater. The impact of mining and subsequent restoration of the surficial aquifer on the ground and surface water resources of the watershed affected by the mining will be described. This will be done in terms of ground water recharge, ground water levels, and base flow and runoff to surface streams. Data from actual mining situations will be used in analyses and discussion. Recommendations will be made for further research.

Jan 1, 1992

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By K. S. Narasimhan, T. C. Rao, R. Bhima Rao

Investigations have been carried out to evolve a grinding aid useful in grinding a 40% iron-bearing magnetite containing quartz as the major gangue, based on studies conducted with pure magnetite, pure quartz and its synthetic mixture. These investigations established that an addition of 200 g of CaO per metric ton of ore was the most effective in grinding quartz preferentially over magnetite at 75% solids concentration by weight. The limited rheological studies conducted suggest that the effect could either be due to dispersion or the structural modification of quartz. More importantly, a new concept, that of Critical Solids Concentration, where two different minerals behave like one with respect to response to communication in a tumbling mill, has been introduced for the, first time. Above this concentration, one of the minerals is ground at a faster rate than the other, whereas the reverse is the case below this concentration.

Jan 1, 1992

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992

By E. Arioglu

Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence (?Smax) induced by chain pillar convergence has been related to a parameter (h/I -p) by linear regression. (Notations are expressed in this discussion's Fig. I (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goaf may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between ?Smax/m vs. h/1-p. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data.

Jan 1, 1992

By W. E. Heinrichs, R. W. Davis

Introduction Cross borehole seismic tomography (CBST) is a geophysical technique that allows definition of the distribution of some physical rock property between two boreholes. The method is similar to the computer-assisted tomography (CAT) scans used by the medical industry. This paper describes the method, its applications and the developing trends in its use that interest the mining industry. The idea of using tomography in connection with geophysical methods for measuring rock properties between boreholes has been around for three or four decades. Until the advent of high-speed, large-capacity computers, the necessary calculations were too formidable for production use. Another factor in the development of the technique has been the refinement of a mathematical base to meet the needs of the medical industry. The geophysical applications have benefited from this refinement. An extensive discussion of the basic theory is given in Kak and Slaney (1988). CBST, although widely researched and written about, is still not extensively put to use in mining and engineering projects. Most real world examples in the literature have come from research carried out by government laboratories or by large companies. An exception is the regular use by Prospection Geophysique Francaise (Cottin et al., 1986) in damsite investigations. The Japanese appear to be doing extensive research and testing of CBST's uses in civil engineering projects (Saito et al., 1988). Canada is researching the use of the method in connection with nuclear waste site investigations (Wong et al., 1987). Finland has tested the method in connection with a foundation investigation for a nuclear power plant (Cosma et al., 1984). In the US, the US Bureau of Mines has taken an interest in using CBST as a means to enhance in situ mining operations (Tweeton, 1988). Major oil companies are examining the method as a tool in oil field development (Justice et al., 1989). Description of the method CBST involves placing a series of receivers down one borehole and recording transmissions from an energy source placed successively at a series of positions in another hole. The objective is to generate a dense network of seismic raypaths between the holes. The denser the network of raypaths, the better the features between the boreholes are resolved. Either seismic travel times or sine wave amplitudes are measured by the receivers. Analysis of travel times between boreholes develops a picture of rock velocities between the holes. Analysis of seismic wave amplitudes develops a picture of the distribution of energy transmission characteristics between the holes. These seismic properties can be used to define occurrences of fracture zones, lenticular sequences or other important geologic data not apparent from examination of the borehole logs. When longitudinal (compressional) and transverse (shear) waves are analyzed, the physical properties, such as elastic moduli, can also be mapped. When wave amplitudes are measured, rather extensive corrections to the data are necessary. There is some disagreement among researchers as to the feasibility of making some of the corrections. For this reason, this paper will concentrate primarily on travel time analysis. Wave amplitude analysis will be mentioned occasionally only in passing. This does not mean that amplitude analysis does not provide important data on rock parameters, only that for the present there are limitations on its uses. Vertical seismic profiling (VSP), extensively used in recent years in oil exploration, is similar to CBST. Instead of using two boreholes, however, the VSP method uses an array of seismic sources or detectors down one hole and an array of detectors or sources along the surface radiating outward from the hole. While adequate for determining vertical velocity distributions, the VSP method is not, by itself, suitable for most engineering or mining projects. Computer programs used to analyze the field data make use of the fact that the total travel time or change in signal amplitude between boreholes is described by Dines and Lytle (1979) as: [9k = f Rk f( x,Y) ds (1)] where gk = the total time or attenuation along the kth ray path,

Jan 1, 1992

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992