Search Documents

The development of technologies to improve mining and mineral processing is an ongoing process. These new technologies are the result of the industry’s drive to lower costs and improve productivity. Many technical conferences allow mining industry professionals to learn about these new technologies and possibly implement them in their own operations. In early November 2005, The 14th symposium on Mine Planning and Equipment Selection (MPES) was held in Banff, Alberta. It was jointly held with the Fifth International Conference on Computer Applications in the Minerals Industries (CAMI).

Jan 1, 2006

The two candidates in the upcoming presidential election in the United States each say that they have their own solution to the nation?s energy problems - solutions that will increase the amount of energy available, lessen the nation?s dependence on foreign sources and reduce the amount of pollution released to the atmosphere. Democratic nominee Sen. Barack Obama and Republican candidate Sen. John McCain both advocate research funding for coal-to-liquids and clean coal technologies. McCain also supports increased oil and gas drilling offshore. And Obama has even made some noises in that direction, although his plan leans heavily on the increased use of renewable energy sources. The energy debate is not new to this election. Congress and whichever party is in the White House has for years been trying to craft a comprehensive energy policy. One difference in this latest debate is that the increased use of nuclear energy has gained more attention. Current President George W. Bush has said he favors the increased use of nuclear power as part of the nation?s energy package. And McCain said he supports the building of more nuclear power plants. Obama has not said much about that. The American public is also showing signs of changing its stance on nuclear energy. To be sure, images of Three Mile Island and Chernobyl are still alive in some minds. However, the American public has said it wants cheaper energy and they want it produced more cleanly. With nuclear, the nation can have both. In the United States, nuclear accounts for slightly less than 20 percent of the electrical power used (see interview with Gary Steele of Energy Fuels on page 27). Globally, that figure is about 15 percent. And there are several nations that derive better than half of their power from nuclear sources. Add to that the world?s increasing need for more energy and the future of nuclear is bright.

Jan 1, 2008

By P. Todd, K. Dever, P. S. Mills, A. A. Campoli

Resin bolt performance is dependent on the size of the resin annulus, i.e., the difference between the hole and bolt radii. The majority of the millions of resin roof bolts installed each year in the United States employ an annulus of 3.175 or 4.775 mm (0.125 or 0.188 in.). Short encapsulation pull tests with resin annuli of 3.175 and 2.413 mm (0.125 and 0.095 in.) resisted an average of 0.08 t/grouted mm (2.25 st/grouted in.) with no significant variation. Resin loses to simulated fractures increased as annulus size decreased.

Jan 1, 2003

By Thomas W. Smelser

A full-scale geotechnical model of a 15-foot (4.6 m) wide coal mine entry in correlation with computer finite-element analysis (FEA) is being employed at the Bureau of Mines Spokane Research Center for basic research on roof-bolt support systems. Physical and computer modeling of various coal mine roof-bolt reinforcement systems will increase our basic knowledge of how roof supports function. This information, in correlation with computer FEA and underground verification tests, will provide a basis for establishing safer, more cost- effective roof control plans and help establish guidelines for employing fully grouted and conventional bolting systems. The basic rationale for the research, research approach, methods and equipment employed, results to date, and future research plans are described in this paper.

Jan 1, 1982

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By Kegomoditswe Koitsiwe, Tsuyoshi Adachi

"This paper characterizes quarterly LME copper price fundamentals from 1995 to 2011 by analyzing the transformation of the market mechanism based on structural change perspective. Using chow test for structural change based on the least square multiple regression, we divide the price fluctuation into: Stable price period (1995Q3-1999Q2), Low stable price period (1999Q3 – 2003Q3) and Price fluctuation period (2003Q4 – 2011Q2). The results show the existence of structural breaks disproves the investigation of the full sample period as a whole. In different structural breakpoints the main drivers of copper prices changes and their impact are significantly different. Moreover, the paper examines the role of speculation in copper price fluctuations.Introduction The rise in commodities price volatility and financial and economic crisis have led to questions over the organisation of futures and physical commodities markets. Spikes in commodity prices and volatility have coincided with a surge in financial speculators in the commodity markets inspiring a polarised and hotly debate among academics and practitioners about the role of investors in the development of physical markets. In his seminal work Kaldor (1939) focused primarily on whether speculative activity in the futures markets reduces the variance of commodity spot prices. Yet, part of the literature finds that the introduction of futures contracts destabilizes the spot market. IMF (2006) studied commodities boom and its causes concluding that there is little support for the hypothesis that speculative activity affects either price levels over the long run or price swings in the short-run. The impact of speculative activity on commodity prices remains a highly contentious topic. Other market analysts take the view that the supply and demand for physical commodities remain the major determinants of market trends (Krugman 2008). It is the aim of this study to contribute to the literature by examining the drivers of copper price changes from a structural change perspective. In this context we are attempting to answer to: What are the main drivers leading to copper price fluctuations? Are these factors having the same effect in different periods or not? It is meaningful to understand drivers of copper prices and thereby, their fluctuations because it will help developing countries depending on copper export to anticipate market situation and avoid bad economic development challenges that can result from price fluctuations. Moreover, this can ensure sustainable mineral supply."

Jan 1, 2017

By M. A. Candia

Stability analyses were performed on the La Libertad, Nicaragua existing tailings embankment in order to determine the conditions for the minimum buttressing required for stability of the dam as a short term measure. Two critical sections, shown in Figure 1, were investigated under static, drained and undrained conditions for existing and modified geometries. The existing geometries reflect the "as built" topography of the dam, and the modified geometries reflect the implementation of a toe berm to buttress the slope. For these geometries drained and undrained conditions as well as different elevations of the toe berm were evaluated against a factor of safety.

Jan 1, 1996

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

By Tom Szaraz, Steve Skelhorn

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer (BWOAS) consists of 4,000m (13,200 ft) of 3.66m (12 ft)diameter tunnel passing mainly through glacial deposits with a water head of up to 2 bar. The project involves many new innovations, including: Slurry wall work shaft with excavation below the water table; Hybrid universal rings combining traditional steel reinforcement with fibers; New, full EPB Lovat TBM; Two component grout system pumped to the TBM from the surface; and, Linabond corrosion protection liner. The paper looks at the planning approach adopted to meet the various challenges presented, combined with an overview of progress to date.

Jan 1, 2007

By G. Babut

The restructuring of mining operations in Valea Jiului coal basin imposed by the transation to the market economy calls for an increased coal production. Under the circumstances, the role of drainage networks grows ever more important. The paper describes an original mathematical model and software developed on its basis, with enables the ventilation engineer to assess the configurations of different systems, as well as to test their reliability and prognose their future performance before conceiving another methane drainage system or changing the existing one. The paper also includes the underlying principles of an optimization program for methane drainage networks, which will enable the detection of the optimal methane drainage system, both from a technical and an economic point of view.

Jan 1, 1996

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By D. R. Gibbons

This morning I would like to speak to you about an area of chemistry that is enjoying a revival-organometallic compounds. This renewed interest, principally stimulated by defense needs, has already created new markets for the products of the mineral industry. Although the consumption of metals in these new products is modest at oresent, several hold promise of importance. Because this is a new and growing market, I am sure the Council of Economics is aware of many of its facets and is interested in new developments. Of course, the chemical industry has been a significant consumer of minerals for many years. I estimate that in 1957 the chemical-industry purchased a total of $1175 million worth of minerals as raw materials (not including fuels). This estimate can be broken down as follows: [Metals and metallic minerals $375 million Nonmetallic minerals (excluding hydrocarbons ) 330 million Hydrocarbons 470 million $1175 million]

Jan 1, 1958

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By Bradford F. Townsend, Gary Peach, Roger Rothenburger

From the experience of the authors on recent large infrastructure Design-Build projects this paper reviews major lessons for Contractors and Owners in the delivery of large Design-Build infrastructure projects and some major pitfalls and warnings to both Owners and Contractors. The paper is written from both the Design and Construction perspective. A case history is presented that details the approach employed to ensure a quality project consistent from the initial design phase through construction and outlines the strategy used to guide the Design-Build process to an acceptable completion. Suggestions are made for Contractors and Owners for handling the Design and the Construction elements of Design-Build contracts.

Jan 1, 2003

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By R. L. Pozzo, I. Iwasaki

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying Faraday's law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a non- magnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-

Jan 1, 1988

By John T. Cumberlidge

The Groveland deposit, in the Upper Peninsula of Michigan, consists of an E -W trending overturned syncline of Middle Precambrian Vulcan iron formation. At Groveland, the Vulcan formation can be divided into four units or facies. The total succession may be more than 550 feet thick, and consists of a basal unit composed of a lean chemical quartzite with traces of magnetite; a non-banded, partly clastic unit characterized by the preponderance of hematite over magnetite; a transition unit of well-banded magnetite-bearing iron formation interbedded with non-banded oolitic hematite; and a well-banded magnetite-quartz silicate unit at the top of the exposed sequence. The present magnetite-hematite ratios of different units within the orebody are considered to be a primary (post-diagenetic) feature of the original sediment. Subsequent regional metamorphism has increased the grain size of the original iron oxide minerals, but did not appreciably alter the oxidation state of the original sediment.

Jan 1, 1964

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

4.1 INTRODUCTION There have been numerous methods developed for predicting the final subsidence and final displacement profiles (Voight and Pariseau, 1970; Brauner, 1973a; Kratzsch, 1983). But for discus- sion purposes, they can be classified into six categories: theoretical, profile function, influence function, graphical, physical, and numerical modeling. The theoretical method employs mainly continuum mechanics theories and attempts to explain the mechanisms that lead to sur- face subsidence. Many models using nearly all kinds of material behavior have been developed. These include elastic (Salmon, 1963; Berry, 1964), plastic (Pariseau, 1968), viscoelastic (Iman, 1965), and elastoplastic (Dahl, 1969). The Profile Function Method is essentially a method of curve-fitting against the measured subsidence profiles in a particular mine or region. There are more than 20 profile functions developed empirically for nearly all major coalfields in the world. These include, to name just a few representative ones: Hungary (Martos, 1958), Japan (Hiramatsu and Oka, 1968), Russia (Avershin, 1947), United Kingdom (Wardell, 1965), and USA (Peng and Chen, 1981; Karmis et al., 1984). The NCB's graphical method in the subsidence Engineers' Handbook (1975) also belongs to the profile function method. The influence function method was first proposed by Bals (1931/1932). It was further developed in various periods and stages by Knothe (1957), Liu and Liao (1965), Brauner (1973a) and Marr (1975). This method is now widely used in various parts of the world. The physical models include sand (Litwiniszyn, 1959; Pariseau and Dahl, 1968) and gelatin (King and Whetton, 1958; Khair et al., 1986). They are used mainly to study the parameters that control subsidence behavior. The most popular numerical method is the finite element technique. It can simulate nearly every conceivable material behavior, inhomogeneity, bedding planes, anisotropy, and various boundary conditions. This versatility is absolutely necessary considering the ever-changing geologic and mining conditions encountered. In the following sections, only those methods that have been applied to US coalfields will be discussed. Furthermore, the methods for prediction of several key parameters such as maximum subsidence, maximum possible subsidence, and maximum displacement are discussed first, because they are the key parameters to be used in the profile function, influence function, and graphical methods.

Jan 1, 1992