Search Documents

Train services through the Channel Tunnel linking Britain and France where scheduled to be fully restored in February 2009 following several months of repairs after a major fire in the tunnel on Sept. 11, 2008. A lorry caught fire on a shuttle train carrying heavy goods vehicles bound for France through the 50-km- (31-mile-) long northern tunnel. The fire, that spread to other vehicles, raged for about 16 hours. The extreme temperatures of up to 1,000º C (1,832° F) caused extensive damage to about 600 m (2,000 ft) of the 7.6-m- (25-ft-) diameter tunnel?s concrete lining, approximately 11 km (7 miles) in from the French entrance. The Channel Tunnel operator, Eurotunnel, awarded the repair con-tract, estimated to be between ?50 to 60 million, to a consortium of Freyssinet, Eurovia Travaux Ferroviaires (ETF) and Vinci Energies. Freyssinet was appointed to look after the civil engineering works, while ETF would be responsible for track and overhead wire restoration and Vinci Energies responsible for other equipment. The technique of hydrodemolition, which uses high-pressure water jets to remove concrete from various structures, was specified as the method to remove the fire damaged concrete. Freyssinet subcontracted the concrete removal to the specialist hydrodemolition and industrial cleaning contractor Philip Lasserat.

Jan 1, 2009

By W. H. Strickland

The research reported here characterizes ultrasonic ranging sensors for autonomous navigation on underground mine mobile equipment. Because ultrasonic rangers are inexpensive, have no moving parts, have no lenses to clean, are small and unobtrusive, and can measure distances in dusty environments, they are especially sui ted to underground mi ne environments. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of individual rangers and a ring array of 24 sensors. The results showed the sensors have good accuracy and low variability. Additional experiments at AHAX' s Henderson mine Showed the sensors could accurately and reliably measure rib features, convex and concave corners, and drift intersections. The results showed that when used and analyzed properly, the sensor data may be used reliably for underground mobile equipment navigation.

Jan 1, 1990

By A. J. Romeo

The Old Hickory heavy mineral ore body, which lies within the Fall Zone of south central Virginia, has been mined since 1997. There are many differences in this deposit when compared to humate-laden mineral sands mines of southern Georgia and Florida. These differences include an abundance of kaolin-rich clayey sands, highly concentrated and iron-colored heavy mineral sand units, and a base of mineralization that is undulating. For these reasons, the selective approach of dry mining with track excavators is ideal. Grade control in this deposit uses traditional panning techniques and requires an intimate working knowledge of near-by drilling data. Mine geologists train equipment operators to recognize the base of mineralization by such characteristics as a stark color change, significant changes in grain size, and/or considerable, recognizable shifts in the concentration of heavy minerals. The regular pattern of mine site drilling does not always prepare the geologist and digging crews for occurrences of near-vertical contacts between the saprolite basement and the ore sands. These deformed areas, combined with undulating and pinching ore zones, require close monitoring and flexibility by the geologist and the mine operators.

Jan 1, 2005

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By M. A. Stoakes, H. D. S. Miller

Surface subsidence is becoming an increasingly important factor in the economics of mining Louisiana salt domes due to, amongst others, excessive shaft deformations and land loss to encroaching sea water. The vast majority of subsidence studies have been undertaken on bedded, tabular deposits. It is important to understand the causes of subsidence due to mining domal salt and how it can be minimized. The paper will review the major differences between subsidence caused by domal and tabular evaporite mines, the problems encountered in predicting subsidence, the factors that influence subsidence and, finally, possible alternative mining methods.

Jan 1, 1986

By W. L. Wilson

This article could be entitled "The Rediscovery of the Windfall Mine," since it was originally discovered early in this century. The "Rediscovery" was made by personnel of Idaho Mining Corp. during the course of an investigation of the Windfall mine beginning in 1967. There had been historic production from the Windfall mine sporadically from 1908 until 1951 and there was present during much of this time a mill that vat leached crushed ore. Mining was underground to a depth of 91 m (300 ft). Prior to Idaho's activities, the mine had been inactive since the early 1950s. Idaho Mining Corp. was an "exploration company," privately owned and based in Reno, NV. The writer was at that time manager of exploration for Idaho Mining. The company held interests in the Cortez Gold mine, then being readied for production, and had conducted exploration for various mineral commodities in Nevada for several years. Idaho's attention was first directed to the Windfall mine in the Eureka District, Eureka County, Nevada (see Fig. 1, Nevada map) by a search of published geologic literature of the state of Nevada. An attempt was made to acquire a library consisting of all of the published geo-data for the state of Nevada as well as to obtain as much of the unpublished material as could be acquired. A study of these data, and in particular Tom Nolan's Professional Paper 406 (1962), indicated that the Windfall mine was anomalous for the Eureka District in that it contained deposits of disseminated gold. This source and other sources indicated that the Windfall had produced from underground operations approximately 59 kt (65,000 tons) grading 12.6 g/t (0.368 oz per ton) gold ore that was processed in a vat leaching operation and that the gold was "invisible" to the naked eye and could not be panned. It was ascertained that there were no active operations near the mine and a geologic reconnaissance was made and a few samples were taken to attempt to determine if the mineralization was indeed disseminated. The initial group of samples around the mine area averaged 1.25 ppm [11.5 g/t gold (0.036 oz per ton)] and the mineralization did appear to disseminate into the wallrock. The next step involved researching the ownership of property in the immediate area of the mine, and [ ] a property map was constructed that showed six or seven different ownerships of patented and unpatented claims, as well as some open ground, in the target area. Negotiations were commenced with the claim owners, ultimately resulting in the acquisition of all of the desired property, although some of

Jan 1, 1990

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By P. A. Dimas

A new family of sulfide flotation collectors has been developed in our laboratory. These formulations are comprised of novel renewable materials combined with conventional reagents. The resulting diversity permits tunability of collector chemistry to meet a range of flotation problems. Several attributes of the new collectors are presented.

Jan 1, 2012

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

P.T. Freeport Indonesia's latest expansion has increased total mill throughput to 125,000 dry metric tonnes per day. The most recent expansion included the installation of a Semi Autogenous Mill designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation including conventional and column cells and a regrind circuit. All equipment is supported by a modem distributed control system. This paper describes the design considerations, construction, commissioning and start-up of the SAG concentrator and support facilities and includes an overview of the oreflow and milling facilities.

Jan 1, 1996

By Arthur L. Raub

During the last decade, there haven't been any great innovations in the design features of a copper concentrator. What has worked well in the past continues to work well, so that major breakthroughs have been minimal. Conservatism in the ranks also plays an important part. As a copper concentrator is not designed and built everyday, Davy was elated to have an important part in this project. This is the story of the design of the oracle Ridge Project located north of Tucson on the back of Mt. Lemmon at an elevation of 5,900 feet on the N.E. slope of the Catalinas. The Oracle Ridge property, formerly known as the Control Mine, is owned by Oracle Ridge Mining Partners, a joint venture between Continental Materials Corp. of Chicago and Union Miniere of Brussels, Belgium; both or¬ganizations specializing in the non-ferrous metal industry.

Jan 1, 1979

By R. J. Sawyer

*An earlier version of this paper was presented at the IMM meeting, "Use of Cultivated Carbon in Extraction of Gold and Other Metals," held in London in January, 1983, and was subsequently published in Trans. IMM (Sect. C: Mineral Process. Extr. Metall.) in December, 1983. Reprinted with permission of The Institution of Mining and Metallurgy, London. INTRODUCTION This paper describes the development of the processing route for the Alligator Ridge Mine which commenced operation in 1980. It also reviews the modifications which have been made to improve operating efficiency during the three years that the mine has been in production. Alligator Ridge is located 70 miles Northwest of Ely, Nevada. The mine is a joint venture between Amselco and Nerco with Amselco acting as operator. The deposit consists of micron sized disseminated gold imbedded in siltstone. Although definitive conclusions have yet to be drawn as to the age and origin of the deposit, it is probable that it is young by geological standards, perhaps only 5 million years old. It is likely that the gold was brought to the surface by hot springs. As the superheated solutions rose through the porous siltstone, they redeposited minerals in the rock, forming the present ore bodies.

Jan 1, 1984

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By W. A. Vine

Next year, in 1964, Butte will celebrate its Centennial. It was in May, 1864, that the first recorded mining activity took place. During that summer, several rich placers were found on Silver Bow Creek and its tributaries, and a gold rush followed. As placer mining proceeded in the creek beds, the quartz lodes on the hillsides were located and the veins were prospected. Mining in Butte entered its second phase when the rich silver mines, the Alice, Moulton, and Lexington, were opened. The silver boom lasted until the decline in the price of silver in the early 1890's forced the closure of many of the mines. An indication of the beginning of the copper mining era in Butte was in 1866 when it was noticed that green copper carbonate discolored some of the, lode material. It was not until ten years later, however, that the Anaconda and St. Lawrence claims were located by Michael and Ed Hickey. The claims were sold in 1880 to Marcus Daly and in 1881, Daly obtained financing and organized the Anaconda Silver Mining Company to exploit the vein The silver venture was a failure because of the predominance of copper which diluted the bullion to only 400 fine.

Jan 1, 1963

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By T. J. van der Walt

This paper proposes a new methodology to model ill- defined processing operations using neural nets (NN's). A process with many variables (large dimensionality) cannot be modelled adequately if limited process data are available. This problem of multi-dimensionality is addressed and an approach suggested to reduce the dimensionality using NN's. The result of this modelling methodology is a combined model of phenomenological expressions and NN's. The model can successfully be incorporated in a dynamic simulator of the process. A new approach to conduct modelling on the basis of continuous data collected directly from an industrial processing unit, is also proposed. The modelling methodology is applied to a typical processing operation, the resin-in-pulp (RIP) process.

Jan 1, 1992

By Ben H. Daud

The systems optimization approach to mine planning has led to the adoption of a number of mathematical and computer models for short, medium and long range planning of mining operations. In the realm of open pit mine planning, the most common uses of such an approach have been in the areas of optimal pit design and planning of materials handling operations. Since a truck-shovel combination is the most widely used method of materials handling in open pit mines, a number of models have been presented in the past to analyze and optimize such systems. Broadly, these models can be divided into two categories. The simulation model, which is primarily used as an aid in analyzing the performance of either an operating or a proposed haulage system under the influence of externally alterable parameters, and the linear or integer model which is used as a tool for short or medium term optimization of the system under the operating constraints. In the first part of this paper, a brief discussion is presented of the linear/integer optimization models presented in the past, and in the second part a new model is described which is actually a combination of the simulation and the integer programming models. In its bare essentials, the model consists of an integer optimization algorithm, but the constraints are regularly and dynamically updated by incorporating the conclusions drawn from a stochastic simulation model of the mine haulage system. Since the successive optimization is performed by the mine operator who manipulates the constraints to guide the model towards the optimum, the mystical black box approach is minimized and should help in adoption of the model by the mine personnel. Also, by combining the stochastic simulation model and the deterministic integer model, some of the advantages of each are acquired.

Jan 1, 1976

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984