Search Documents

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite's use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are. the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread- sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin.

Jan 1, 1987

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By Abdullah Arik

An ore reserve block model is the basis for various decisions in mine development and production. The block model is initially built using the information from the drillhole data only. Once the mine is put in operation, the information from the blasthole data becomes available. Since the spacing of the blastholes are much closer than the exploration drillholes, the blasthole data gathered from the mine over the years become quite extensive containing valuable information about the deposit. In practice, the information from the blastholes is the basis of determining the ore and waste boundaries between and within mining blocks. In an ore reserve model, the valuation of blocks on and close to the pit face can obviously be improved by using blasthole data from neat by drilled and mined-out blocks in addition to using the widely spaced drillhole data. The ideal basis on which to integrate blasthole and drillhole data is to use cokriging.

Jan 1, 1996

By J. E. Lonergan

The in-pit placement of crushing and conveying equipment results in a flattening of the pit slope of a multiple-bench open pit mine. To maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must minimize the cost of the flatter slope which is expressed in terms of additional stripping or tied up ore. A computer program that compares the tonnage aspects of various conveyor layouts will be discussed.

Jan 1, 1985

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By Hitch M.

Many mining wastes, especially those from the metal mining industry, have traditionally been treated as a matter of little or no value and in practice a cost burden. Some wastes, due to their reactivity characteristics, have emergent values that go beyond purely economic and into the environmentally beneficial realm. This paper discusses the changing paradigm of mine waste management. Such fundamental parameters such as cut off grade, and strip ratio, are positively impacted by the revaluation of waste rock material. Mine rock waste can now be seen as a commodity of value, similar to the underlying ore being mined and influences the economic performance of suitable projects. This valuable material can be used for industrial purposes including acid neutralization as well as the capture and long-term disposal of anthropogenic carbon dioxide. The Turnagain Nickel project, located in northern British Columbia serves as an example of how waste rock material can become an important matrix for carbon capture and sequestration and can benefit economically from it. By producing material that has emergent economic value as well as carbon capture and sequestration capabilities, the sequestration matrix producer is a beneficiary of new carbon credits that have a market value and is looked upon favourably by regulatory authorities and affected stakeholders.

Jan 1, 2010

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By G. A. Campbell

This paper considers the international market trends of the rare earths and how they are strongly influenced by the by-product/co-product nature of their mining and processing. The two main economic minerals for the rare earths are bastnasite and monazite. Monazite is primarily a by-product of mining ilmenite and rutile and is affected by changes in these markets as well as the presence of thorium. Bastnasite is a by-product of mining iron ore in China and a stand-alone product in the USA. The paper will use conceptional relationships and empirical data to delineate the various by-products/co-products relationships and how they determine observed international market behavior.

Jan 1, 1996

By D. W. Gunkle

Processing of various ores and materials in a reducing atmosphere has been done for many years. However, the typical device currently used is a large, often high maintenance, expensive piece of equipment; the rotary kiln. While it is a very reliable and a proven technology, the rotary kiln also has its limitations. It is limited by its ability to process very fine materials without creating a huge dust loss to the air pollution control equipment. This leads us towards the development of an alternate technology; the Gas Suspension System. Gas suspension preheating of various materials has been in commercial use since the early 1950's, but recently has been expanded to include Gas Suspension Reduction. Laboratory experience has proven successful on several materials; Nickel Laterite Fines, Iron Ore Fines, Fluorspar, and Clays. The gas suspension reduction system has many advantages over the conventional reduction kiln when processing fines. They are; lower cost, more fuel efficient, able to process fines, less real estate required, etc.

Jan 1, 1998

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By A. Newman, M. Goycoolea

"In this paper, we consider an underground production scheduling problem consisting of determining the proper time interval or intervals in which to complete each mining activity so as to maximize a mine’s discounted value while adhering to precedence, activity durations, and production and processing limits. We present two different integer programming formulations for modeling this optimization problem. Both formulations possess a resource-constrained project scheduling problem structure. The first formulation uses a fine time discretization and is better suited for tactical mine scheduling applications. The second formulation, which uses a coarser time discretization, is better suited for strategic scheduling applications. We illustrate the strengths and weaknesses of each formulation with examples.IntroductionProject scheduling is an important aspect of underground mine planning that consists of determining the start dates for a given set of activities so as to maximize the value of a project while adhering to operational and re-source-availability constraints. Important activities that require scheduling include development, drilling, stoping and other ore-extraction techniques, and backfilling. Precedence relation-ships impose an order in which activities can be carried out based on their location in the mine: for example, the activity a associated with development of an area must be completed before the activity a´ associated with extraction of that same area can begin. Re-sources include attributes of the mining operation, such as the amount of extraction and mill capacity available per time period, and are determined by capital and equipment availability and other factors. In this paper, for our set-ting, resource-availability constraints consider the amounts of material that can be extracted and sent to the mill — that is, processed — per time period."

Mar 1, 2017

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By John J. Rhodes

I welcome this opportunity to give a Congressman's birdseye view of a subject which I believe holds great potential for the future in helping meet the needs of people, with minimal adverse impact on the environment. All mankind, not just the people in this great nation, faces the need for additional usable space. In some parts of the United States the problem arises from rapid urbanization of the surface and little utilization of the subsurface. Everywhere there is an increasing problem of insufficient space arising out of the increasing population crush and growing demands for open space, housing, water, transportation, communication, and social service. You are the technicians to whom we look for assistance in finding answers. We look to you also to provide guidance for broad policy decisions concerning underground space. I prepared for a career practicing law, but since 1952 I have been a member of the House of Representatives. In this latter capacity I deal with programs designed to help solve all kinds of problems. But, naturally, I am especially interested in the water scarcity and other environmental problems of my home state of Arizona and the arid and semi-arid areas in the West. This North American Rapid Excavation and Tunneling Conference has as its theme: "Tomorrow's Tunneling Technology Today." I have a very great interest in this potential of our underground space resource. The Central Arizona Project now getting underway in my state will consist in part of tunnels and underground pipelines to convey life-sustaining water from the Colorado River to people and lands across Arizona to the Phoenix and Tucson areas.

Jan 1, 1997

By T. Weatherwax, A. Rai, J. Poor

"This paper provides an overview of the current use of auxiliary ventilation products and the challenges with limited air quantity in dead-end entry or working faces. The PVC’s low frictional factor, low physical constraint and minimum leakage properties were ideal to develop as ventilation duct in conjunction with the concept of ""Made in the US and Used in the US"". The PVC duct supports the operational and total cost of ownership with on-going success. This paper will discuss the continuous improvement made in ventilation ancillary products for optimum results. The paper will also cover mine site usage of second generation PVC vent duct underground and the results from the operational and technical side making a difference in health and safety and overall auxiliary ventilation. INTRODUCTION The Barrick Turquoise Ridge Inc. (TR) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone, siltstones, and mudstones. The weak nature of the ground facilitates the need for underhand cut and fills mining methods.Mining Method; Underhand cut and fill: The mine uses underhand cut and fill method which has 12’x12’ and or 14’x14’ top cuts with several different size undercuts. The ore body is accessed off of a secondary tertiary heading, utilizing a heading with a cross section of 14W x 14H or 15W x 15H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the ground conditions and drift dimension. An example of a typical topcut and associated undercut layout is shown in Figure 2."

Jan 1, 2016

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.