Search Documents

By G. E. Karantzavelos

Introduction Pure alunite (KAl3 (SO4 )3 (OH)6 ) contains 37% A1203. In the alunite ore found on Milos Island, Greece, opal is the principal gangue while some aluminum, iron, and titanium oxides are also present. Processing of alunite ore leads to the recovery of potassium sulfate, alusil (alumina-silica mixture), and sulfur dioxide. An interesting process has been developed in Greece (Svoronos, 1977) consisting mainly of roasting the alunite ore mixed with KCl to disrupt the mineral lattice in preparation for separating its components. The thermal decomposition of alunite at approximately 600°C occurs by the reaction: KAl3 (SO4)3 (OH)6 + nSiO2 + 6KC1 - 4 K2SO4 + 3 A1203 . nSiO2 + 6 HCl + 3H20 According to the process pure alunite mixed with 543 kg KCl, 840 kg K2SO4, 370 kg alusil, 264 kg HCl, and 65 kg H2O are produced. The roasted calcine is leached in hot water. The potassium sulfate leach slurry is then thickened and washed to obtain a solid residue (alusil) plus a solution rich in potassium sulfate. Assuming the alunite ore feed consists of 50% to 60% alunite, the solid residue might consist of approximately 22% to 27% A1203, silica, iron, and titanium oxides. This leach residue could be digested in a hot sodium hydroxide solution to dissolve alumina. An amount of the alumina (approximately 10%) would not dissolve. In addition, part of the silica would dissolve requiring removal from the solution in a subsequent desilication operation. The same leach residue could be attacked by mineral acids such as a diluted hydrochloric acid to extract aluminum chloride (Sawyer et al., 1983). Alumina and aluminum are presently produced from bauxite of which Greece has important reserves. If this aluminous material (alusil) could be beneficiated by any physical process, then it would be considered as a raw material for the production of fire-clay refractories instead of an alternate source of alumina. Experimental procedure Extensive laboratory work (mineralogical and chemical analyses) indicates that alusil is a mixture of liberated (mostly) alumina and silica particles, not a natural silicate mineral. Table 1 shows the chemical assays of two alusil samples that were obtained from a roasted alunite ore leaching pilot plant. The samples used for the experiments were a very fine alusil powder (K80 = 400 mesh, 38 µm). These were pulped in tap water. Desliming of the pulp before each flotation test was ineffective. Flotation tests were performed in a 2000 ml Denver cell. A standard 500-g sample was first conditioned at a pulp density 50% solids for 5 min with hydrofluoric (HF) acid solution (40%). The temperature of the conditioned pulp was measured and kept nearly constant at 50°C. The pH of the conditioned pulp was also regulated to 2.5-3 with HF solution. Then ARMAC C solution (2%) as well as two drops of fuel oil and one drop of AEROFROTH 65 were added and the pulp was reconditioned for 2 min. After conditioning, the viscous pulp was transfered to the flotation cell. It was then diluted with warm water to about 15% solids and floated to separate silica from alumina particles. A rougher froth product that was cleaned and recleaned was obtained from the flotation tests.

Jan 1, 1987

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By M. Phillip Jameson, Paul Sennett

The beneficiation of kaolin by flotation has been practiced on an industrial level since 1961. A brief history of industrial kaolin flotation is given, with a description of the various processing schemes used by the companies that practice kaolin flotation. Some of the areas where improvements could be made in the beneficiation of kaolin are given.

Jan 1, 1989

By Robert Seal, James J. Rytuba, Michael P. Hunerlach, Roger Ashley, Dean Enderlin

Cessation of open pit mining in 1996 at the McLaughlin hot-spring type gold deposit has resulted in the development of two pit lakes that will be managed as permanent lakes with a total storage capacity of 10,000 acre-feet. The south pit lake developed from alkaline ground water infiltration and had an initial pH of 7.2. It contained high concentrations of boron and chloride, indicating that it consisted of a mix of meteoric and evolved connate waters. Numerous carbon dioxide gas vents were present initially in the shallow south pit lake, but as the pit lake increased in depth, gas venting ceased and carbon dioxide is retained in the lower layer of the chemically stratified lake. Continued increase of dissolved carbon dioxide in the lower layer increases the potential for a limnic eruption. A chemocliie occurs at a depth of 47 m. The upper layer of the lake has lower pH, temperature, and conductivity than the lower layer. Effluent from ore and waste rock piles directed into the south pit lake has contributed to high levels of antimony, arsenic, cobalt, copper, mercury, nickel, and zinc. Iron oxyhydroxide is abundant in mine effluent that enters the pit lake and adsorption onto this phase has lowered the arsenic and antimony concentrations. The north pit lake formed primarily from winter surface runoff. The acidic water, pH 4.56, initially had high concentrations of cobalt, mercury, and nickel derived from weathering products of pyritized serpentinite and shales. Buffering by wall rocks has established a slightly alkaline pH of 7.62. The concentrations of trace metals in the north pit lake have substantially decreased due to continued dilution of the lake by surface runoff and remediation of parts of the pit walls that have been covered by backfill.

Jan 1, 2000

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By M. A. Cocquerel

INTRODUCTION Davy McKee have developed and patented a combined mixer settler (CMS) which has undergone extensive trials and has now been installed in two commercial uranium plants in South Africa. Substantial capital and operating cost savings can be realized over conventional mixer settler in uranium extraction, especially from dilute feedstocks containing approximately 200 ppm U308. Pilot plant work has also been undertaken on other metal extraction systems and the results are very encouraging in most areas of interest. CONVENTIONAL MIXER SETTLERS The conventional plant in use at many uranium recovery facilities consists typically of a mixer box in which the aqueous and organic phases are contacted and a settler in which the two phases separate. The mixer box must allow sufficient residence time for the mass transfer kinetics to be satisfied for the particular species involved. The settlers are usually rectangular and take the form of shallow tanks of large cross sectional area.

Jan 1, 1984

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the Separation Efficiency: ES = (R ? Rg) where R is the percentage of the valuable constituent and Rg the percentage of the waste appearing in the concentrate. The Separation Efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products.

Jan 1, 1969

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

Single-unit separations in mineral processing are typically not able to meet the strict purity requirements for consumer markets. As a result, multistage separation circuits are often employed. Because these circuits represent a large and inflexible capital investment, process engineers are careful to ensure that the circuit is optimally designed to meet the desired objectives. The set of interdependent decisions that constitute the circuit design may involve the selection of different unit operations, different equipment specifications, different operational parameters, and different unit interconnections. To assist circuit designers in assessing these options, researchers have attempted to establish standard design methodologies that involve various techniques and tools.

By Richard D. Lang

Introduction Argyle is located in the Kimberley region in northwest Australia (Fig. 1). It is a significant diamond discovery by world standards and is the first major diamond find in Australia. The deposit consists of a pipe and associated alluvial deposits. Before the 1970s, diamonds were known to exist only sporadically in Australia. They have been found occasionally in association with gold deposits in Western Australia. There is a small deposit near Copeton in New South Wales. Some alluvial occurrences have also been found in Victoria, South Australia, and New South Wales. The first indicator minerals in the Kimberley region of Western Australia were discovered in January 1973. Production from the alluvial deposits at Argyle began in 1983. A $430-million construction program to develop a mine and treatment plant capable of producing 25 million carats per year was completed in December (1 carat = 0.2 grams). Ownership and management Participants in the project are known as the Argyle Diamond Mines Joint Venture. The group consists of CRA Ltd., 56.8%; Ashton Mining Ltd., 38.2%; and the Western Australian Diamond Trust (formerly Northern Mining Corp.), 5%. The project is managed by Argyle Diamond Mines Pty. Ltd., a wholly-owned subsidiary of CRA. Marketing is undertaken separately by the Western Australian Diamond Trust and by Argyle Diamond Sales Ltd. (for CRA and Ashton Mining groups). History Ownership of the Exploration Joint Venture has changed over the last 12 years as various parties changed their shareholdings. The original Kalumburu Joint Venture was formed in 1972 with five participants, each holding a 20% interest. By 1983, a number of ownership changes had occurred. The end result is that two original participants have sold out. CRA now holds a 56.8% share and the Ashton Mining Group holds 38.2%. CRA also assumed project management in January 1977. Table 1 demonstrates the long lead times involved in developing a project.

Jan 1, 1986

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By D. Sotiropoulos

In the recent years, the mining sector is looking for specific indices, taking into account economic, environmental and social criteria, in order to meet the sustainable development requirements. In the present study traditional and environmental sustainable indices used in the Agios Dimitrios Power Plant, Northern Greece, are compared to those of ESKOM Company, South Africa, taken as reference. These indices are referred to, a) the solid fuels consumption, such as lignite, and, b) the emissions to the atmosphere, such as SO2, NO2 and dust. Last five years data show a remarkable improvement of all indices in the Agios Dimitrios Power Plant. Although the lignite used in this Power Plant is by far of poorer quality than that used by ESKOM - net calorific value 1272 and 4638 kcal/kg, respectively - dust emissions in both Power Plants are similar (52 and 31 g/kWh, respectively). The SO2 and NO2 emissions are very low in Agios Dimitrios compared to those of South Africa, respectively 1.92 and 7.91, and 1.74 and 3.61 g/kWh. This is mainly due to natural desulfurization (by the lignite?s calcium content) and the low NOx burners.

Jan 1, 2003

By Robert W. Waytulonis

Miners working in underground mines where diesel equipment is used are exposed to exhaust pollutants. These include carbon monoxide (CO), carbon dioxide (CO,), nitric oxide (NO), nitrogen dioxide (NO2), sulfur dioxide (SO2), hundreds of different hydrocarbons (HC) and particulate matter. Evidence from animal inhalation studies and limited epidemiological investigations have led the National Institute for Occupational Safety and Health (NIOSH) to recommend that ‘... whole diesel exhaust be regarded as a potential occupational carcinogen ...’ NIOSH further stated that ‘... the excess cancer risk for workers exposed to diesel exhaust has not yet been quantified, but the probability of developing cancer should be decreased by minimizing exposure…’ The International Agency for Research on Cancer(IARC) reached a similar conclusion, saying that ‘... diesel engine exhaust is probably carcinogenic to humans.’ Before these declarations, there was insufficient evidence concerning the carcinogenicity of diesel exhaust. It was well known, though, that diesel exhaust caused less severe problems, such as headache, eye irritation and unpleasant odors. In 1988, a milestone was reached in the Mine Safety and Health Administration (MSHA) regulatory process. An advisory committee recommended a three-tier approach to regulating diesels used underground-approval of diesel equipment, safety and health. Diesel particulate matter may be specifically regulated. In addition, ambient air quality standards are being proposed that will establish a new standard for CO2 and lower the permissible exposure limits for the NO2, CO, SO2 and formaldehyde emissions that originate from diesels and other sources. Additional safety and emission restrictions are also proposed for diesel engines in coal mines. The goal of the US Bureau of Mines (USBM) diesel engine research program is to minimize the health and safety problems associated with underground diesel equipment use. Part of this program is focused on reducing exhaust emissions from diesel-powered equipment used in underground mines.

Jan 1, 1993

By B. J. Sauer

Misapplication of ac induction motors for mine crusher and mill applications has long been a frustration for the driven equipment supplier and the mine operator. Proper selection of ac induction motors is critical to providing efficient production. This paper focuses on the selection of ac induction motors for gyratory crusher, conecrusher and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 2002

By David H. Carlson

The paper presents background information including data on diesel exhaust pollutants, amounts produced and standards, a desscription of mine characteristics that affect air monitoring techniques and a review of portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the Experimental Mine, the diesel dilution tunnel test cell, the Mine Air Monitoring Lab (MAML), the portable instruments and the production mines used.

Jan 1, 1979

By B. A. Donahue

The results of a survey of 46 West Virginia coal samples, employing the Office of Coal Research-Band coal sewage treatment process, indicated that the Freeport coal and Bakerstown coal from Preston County, Pittsburgh coal from Harrison and Ohio County and the Sewickley coal from Monongalia County offer outstanding potential for water clarification. Oxidation, steam treatment and acid and base washing of coal generally resulted in small positive or negative changes to the water clarification capacities of the coal while the employment of prepared coal fractions resulted in more significant benefits. Of the coals tested, those fractions with high ash, high sulfur and low Btu generally possessed the highest adsorption capacities.

Jan 1, 1968

By A. M. Gaudin

The recent study by R. M. Hays(l) prompted the study summarized in this paper. In his Interesting paper, Mr. Hays shows fine results to be attainable by a relatively complex flowsheet on a semi-taconite, a manifestly difficult ore to treat. We obtained a semi -taconite from Minnesota, and treated this sample by wet magnetic separation alone. The device in which the separation was accomplished is the standard pilot-plant, laboratory separator in use at Magnetic Engineering Associates' laboratory (MEA) in Cambridge, Massachusetts. It consists of a cylindrical space which can be magnetized by turning on the magnet of the separator. In this cylindrical space, there is a canister which provides the special configuration of the magnetic field and magnetic field gradients that MEA considers to be required. The ore pulp is made to flow through the canister while the current is on. A portion of the pulp is retained in the canister, and the rest is evolved as a non-magnetic fraction. The laboratory device is cyclic, but it accurately predicts the results obtainable by an Industrial unit of either cyclic or continuous type (moving matrix). The ore tested was 99.5°%o -325 mesh, and approximately 75% -500 mesh. The concentrate from this ore was, therefore, eminently suitable for pelletizing. In passing the ore through the magnet, we had the choice of repeatedly passing the concentrate from the first step through the operation, or of repeatedly passing the non-magnetics. In our experiments, the first method was clearly superior from the stand¬point of the cleanliness of concentrate. Of the many tests which we have made, we think that we have to retain two which

Jan 1, 1971

By Majid Sadeghi, Ali Naghi Dehghan, Kaveh Ahangari, Seyed Mahdi Pourhashemi

"Instrumentation and monitoring of ground deformations in tunneling is a principal means for selecting and controlling the excavation and support methods among those foreseen in the design, for ensuring safety during tunnel construction (including personnel safety inside the tunnel and safety of structures located at ground surface) and, finally, for ensuring construction quality management. In this paper, the effect of Hakim Tunnel excavation on the behavior of the surrounding ground was investigated based on the geotechnical instrumentation. This tunnel with 1080 m length, 18 m width and 12.6 m height is being constructed using the SEM/NATM along the Hakim Highway in Tehran. The results which are obtained from recorded displacements by geodetic pins (on the tunnel wall and roof), extensometers and settlements pins (at the ground surface) demonstrate the tunnel stability during the various stages of excavation. However, it is concluded that the rate of excavation in different sequences could have a major role on stability of tunnel. In this case the surface and underground openings were monitored as well as needed for controlling the face probably collapse. INTRODUCTION Tunneling is increasingly being used world-wide to provide the infrastructure required for sustainable urban areas. The high demand for space and the disturbance of existing infrastructures by construction measures increasingly forces future infrastructure projects to be conducted underground. One of the important purposes of tunneling projects in urban area is not only to minimize displacements but also to control them during the construction (Pourhashemi et al., 2015). Normal method of tunnel stability analysis is not able to evaluate the real rock and soil mass behavior. Hence, instrumentation is a practical method to monitor displacements, to evaluate the stability of underground openings, and also to determine the rock and soil mass properties (Dehghan et al., 2012. Dehghan, 2013). Rocks and soils are materials with properties that can change instantly and significantly from one point to the next. Some complications may often happen due to uncertainties in the loads that the new facility must withstand during construction and operation. Instrumentation and monitoring provide quantitative information on actual behavior of ground and adjacent structures. A lot of deformation monitoring studies for determining and analyzing different kinds of engineering structures such as tunnels, bridges, high-rise buildings and dams are implemented. Considering the type of the structure, its environmental"

Jan 1, 2016

This paper provides a summary on the use of the POL YCOM high pressure grinding roll (HPGR) for increasing extraction in copper leaching. The energy-efficiency and significant hydrometa1lurgical benefits of the HPGR result in better acid-curing, higher solution application rates, improved copper extraction from various copper minerals and better recovery from high acid consuming ores. The HPGR's metallurgical features such as micro-fracturing, better liberation of disseminated and veinlet copper, increased oxygen and lixiviant penetration lead to higher copper extractions than achieved by conventional crushing. Flowsheet options, operational characteristics and applications for various copper ores are outlined.

Jan 1, 1996