Search Documents

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By Terry Ramsey, N. Finkelstein

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion I1 was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion I11 followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autogenous grinding circuit, is located in a separate building (Mill 11) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By Georgene Renner

Due to disturbance of their traditional roosts, caves and tree hollows, more than half of the 44 bat species found in the United States and Canada now live in abandoned and inactive underground mines. The North American Bats and Mines Project was created two years ago by Bat Conservation International Inc. (BCI) in Austin, TX and the Bureau of Land Management (BLM) in response to the issue of mine closure and bat habitat. The partnership provides national coordination among government and private agencies and the mining industry to minimize the loss of bats living in mines. It also trains land managers on how to conduct cost-effective mine assessment and closure to protect both bats and people.

Jan 1, 1996

By L. Vinnett, J. Yianatos, S. Flores

"A numerical conditioning analysis for mineral recovery estimation was performed for industrial flotation plants, considering the copper (Cu), molybdenum (Mo) and iron (Fe) separability. A modified relative condition number, ?, was presented that allowed sensitivity analysis to be evaluated for the component recovery by means of an analytical formula. This closed form made it possible for the error propagation to be determined from feed, concentrate and tail grades with different orders of magnitude. The ? parameter can be evaluated using available grade data from the design criteria or historical mass balances, in which the variability is typically unknown. Reconciled data from different Cu/Mo concentrators were employed to evaluate the effect of small numerical disturbances in the grade data on the mineral recovery estimation. Higher error propagation was typically observed for Fe. The Mo minerals presented numerical problems, mainly in second cleaners and in the first cell of rougher banks. Lower condition numbers were observed for Cu due to the higher flotation rates.Mass-balance data reconciliation without redundancy was evaluated for a typical Cu/Mo flotation circuit using relative error minimization. Significant relative errors in the mineral recovery estimation were obtained with nonreconciled data in ill-conditioned problems. Negligible improvements in the mineral recovery estimation because of the data reconciliation with regard to the nonreconciled approach were obtained in well-conditioned problems. In addition, the improvements in mineral recovery estimation by using Cu, Mo and Fe in the data reconciliation were nonsignificant with respect to using only the best-conditioned component in well- and ill-conditioned problems.Despite the effort in data reconciliation and data repetition, poor performance may be obtained in ill-conditioned problems, which can deteriorate the flotation rate characterization. The error propagation has a negative impact on the mineral recovery of the first cell, which may significantly bias the flotation rate characterization of both valuable and nonvaluable elements.IntroductionMass balances have been extensively used in flotation processes to determine the mass flowrates (production) and mineral recovery (efficiency) of valuable minerals. Simple relationships for steadystate processes based on the feed, concentrate and tail grades can be obtained by taking a black-box approach. However, the calculation of concentrate flowrates from different components of the system, such as size fractions, chemical elements or minerals, does not satisfy the mass-conservation principle because of measurement errors (Smith and Ichiyen, 1973; Romagnoli and Sánchez, 2000). Mass-balance data reconciliation allows for obtaining a unique solution that satisfies the total and component mass balances, making small adjustments to the process data and taking advantage of the information redundancy (Narasimhan and Jordache, 2000). This methodology, which is based on a constrained weighted least-squares minimization, has proved to be robust when measurement errors are normally distributed, in the absence of gross errors.Commercial software has been developed to conduct massbalance data reconciliation in flotation processes, including MATBAL (Algosys, 2002), BILMAT (Algosys, 2013), JKMultibal (JKTech, 2013), BILCO (Caspeo, 2013) and HSC Chemistry (Outotec, 2013), which accomplish the reconciliation using known data accuracy in the optimization problem. The data accuracy can be obtained by sampling a stream n times in a run, known as repeats, each with independent chemical assays. Some unmeasured variables can be estimated using the measuring redundancy and sensor location. At present, grade and flow rate sensors may be incorporated in flotation to conduct real-time mass balances. However, a lack of sensor calibration and maintenance for suitable online measurements hinders the quality of the information. In"

Jan 1, 2016

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By Kenneth S. Graham, S. C. Gambrell

A short term, simple roof bolt load cell which uses a birefringent (photoelastic) coating as its sensing element has been developed. The load cell is installed between the bearing plate and the nut/washer and measures the initial force after installation by the bolting machine. The load cell can be removed from the bolt and used again to measure initial force in another bolt if desired. Because temperature and humidity changes in the mine cause creep/relaxation of the coating and/or adhesive, the load cell is useful for accurately measuring force for a period of only two weeks after installation. Force in the bolt is determined by referring to a calibration curve for the load cell.

Jan 1, 1992

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By Randy J. Mikula

Cleaning of low-rank coals can have several meanings, depending upon the definitions of the terms "low rank" and "cleaning." In general, low-rank coals would be lignite or subbituminous according to the ASTM classification. For the purposes of this summary, cleaning is defined to be any process which materially reduces the proportion of inert material in the coal. For low-rank coals, this often means a reduction in moisture content since moisture is the major inert component in these coals. A brief discussion of conventional cleaning processes is included, as is an extensive reference list.

Jan 1, 1991

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By George J. Simchuk

The selection of a stripping method and subsequently, the stripping equipment, are two of the most important decisions confronting a project engineering staff during the initial feasibility study of a new coal stripping operation. The selected stripping units average from 60 to 70 percent of the total capital outlay for mine equipment and their selection will affect the type, size, and quantity of the attendant equipment, such as loading shovels, drills, haulage trucks, and bulldozers. This paper is intended to report on an in depth study by Utah's Technical Services Staff regarding the selection of stripping equipment for the Goonyella Coal Mine in Queensland, Australia. We will touch briefly, on the objectives considered in this selection; the various alternatives which were explored; the general assumptions that were followed throughout the engineering and design of an appropriate stripping system; and computations necessary to determine the amount and size of stripping equipment. INITIAL EXPLORATION Utah Development Company (presently 90% owned by Utah Construction & Mining Co. and 10% by Australian investors) commenced systematic geological studies of the Bowen Basin coal fields of Central Queensland in 1961. The Blackwater Mine as shown in Figure 1 has since been established in this area and is now producing 3.0 million tons per annum of washed coking coal. Geological reconnaissance was then extended to the northern part of the Bowen Basin and in 1963 Utah's coal prospecting area covered 2444 square miles of Central Queensland. The authority to prospect north of Blackwater has since been trimmed to 810 square miles by relinquishments to the State.

Jan 1, 1971

By Stephen V. Thompson

Within recent years portable seismic refraction units have found their place in the industry for shallow investigations, Completely portable, relatively inexpensive and of proven accuracy, the portable refraction seismograph is an electronic tool in an electronic age. The age of electronic instrumentation has seen the development of seismic reflection and refraction equipment for deep exploration, especially in the petroleum industry. Large, expensive units, normally truck-mounted and utilizing explosives, are being used successfully for this type of sub- surface investigation. The portable seismograph utilizes the same theory for shallow work as that applied to deep refraction seismology.

Jan 1, 1964

By Richard Hogg, Heechan Cho

Investigations of long-time grinding of fine quartz (to about 80% passing 0.35 pm) in a 0.6 liter stirred-media mill are described. Breakage rates and primary breakage distributions have been determined based on extensive characterization of the ground products by laser scattering/diffraction and gas adsorption. The results indicate that, while there is qualitative similarity between the breakage parameters for ultrafine and conventional (coarse) grinding, there are important, quantitative differences. In particular, it is found that primary breakage distributions become significantly narrower in the submicron sizes. The trend can be described using double-truncated log-normal distributions in which both a maximum (breaking) size and a grind limit are specified. The breakage distributions become progressively narrower as the size being broken becomes finer. Breakage rates follow a typical, consistent pattern in which the rate decreases with size according to a simple power law. Further decrease in the rates seems to occur after very long grinding times when the entire mill contents become finer than about 1µm. The effect is explained as a result of changes in the rate/size relationship in the submicron range.

Jan 1, 1995

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By P. Shang

Fly ash and zeolite have strong absorption to cations since their porous microstructure. The porosities of fly ash and zeolite can also be increased by modification, which improves the absorption of the materials. This research showed that the effects of modified fly ash and zeolite to remove ammonia nitrogen from rainwater. The optimal reaction time, additive amount of materials, and pH value of the stormwater to remove ammonia nitrogen were experimentally determined. For modified fly ash, the optimal removal rate of ammonia nitrogen from 100 ml stormwater was 74.41% with the addition of 10.0g fly ash, 1.5 hours of the reaction time, and 8 of pH value. To the modified zeolite, the optimal removal rate of ammonia nitrogen was 51.22% at the reaction conditions of 2.0g of zeolite, 1 hour of reaction time, and 7 of pH value.

Jan 1, 2010

By Allen J. Sobczak, Peter J. Peters

The five tunnel contracts of Milwaukee Northeast Side Relief Sewer System are about 80 percent complete. The tunnels are all excavated for 1.9 meter (6'-0") finish diameter sewers in a variable rock, mixed face, and glacial soil environment. Different contracts were let under two primary types of specifications, performance and prescriptive, which treated aspects of construction, such as primary ground support and groundwater control, differently. Interfacing of design and construction through field personnel allowed the needs of all parties to be met and resulted in savings in time and money to the Milwaukee Metropolitan Sewerage District (MMSD). Interfacing, cooperation and risk sharing allowed resolution of problems such as line and grade variations and potential differing site conditions. It also allowed the parties to pursue constructive changes to construction activities. Thus on one contract prescribed use of compressed air was eliminated, but migration of fines into the tunnels was stopped with filter fabric. Use of an expensive primary support system was dropped, but concern about deterioration of lagging was alleviated by use of special materials.

Jan 1, 1983

By M. Kavvadas

Geotechnical design using Factors of Safety recommended by Codes of Practice is based on largely unknown ?margins of safety?, usually without consideration for the importance of the project (i.e., potential consequences of failure) directly or explicitly. On the contrary, probabilistic modelling can be a useful tool in risk management as it provides the means to measure the risk to be managed. This is achieved by calculating the probability of failure associated with a specific design, i.e., by relating the classical factors of safety with the corresponding probability of failure and by using a cost optimization procedure to achieve ?optimal? designs, accounting for the expected costs in case of catastrophic failure. This paper describes the methods used to calculate the probability of failure and its correlation with the classical Factor of Safety using sampling techniques and a simplified method based on the moments of the factor of safety considered as a random variable. These procedures are illustrated in an example which investigates the stability of a slope.

Jan 1, 2005

By J. A. Hartlage

Four years ago, Ashland Chemical Company introduced a new copper solvent extraction reagent for hydrometallurgical utilization. The reagent, an alkylated 8-hydroxyquinoline, is called Kelex 100 ®(1). Since the time of introduction, the reagent has been investigated by several workers for its solvent extraction utility in the separation and purification of transition metals (2-7). In the following text, those factors which are essential to the optimum performance of Kelex 100 on concentrated copper solutions will be discussed. To date, the reagent has been found useful in active concentrations of from 1 to 20% Kelex 100. In order to achieve the best performance for Kelex 100, it has been found that a phase modifier is essential. Various alcohols and phenols have been evaluated in order to improve phase performance and stripping characteristics of the solvent system. Modifiers and diluents are especially important when solvent activities between 3 and 20% Kelex 100 are employed. A 15% Kelex 100 solvent, for example, containing 15% nonyl phenol in Escaid 100 (Exxon) can be utilized to remove greater than 33 grams per liter of copper from an aqueous feed without interstage neutralization, and in the same process scheme the reagent can be stripped to less than 1 gram per liter barren organic producing a pregnant electrolyte containing greater than 40 grams per liter copper and less than 120 grams per liter sulphuric acid. The unusually efficient stripping of Kelex is accomplished by protenation of the extractive molecule during the stripping process.

Jan 1, 1974

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

Magnetic separators are commonly used as an effective and low-cost method to concentrate paramagnetic or ferromagnetic minerals. These versatile separators are often used in multistage circuit configurations to further improve concentrate recovery and/or grade. Although these circuits are generally very efficient, field studies suggest that the layout of multistage circuits can be less than ideal for many industrial operations. To illustrate this shortcoming, a theoretical analysis has been conducted to compare different circuit configurations for magnetic separators. The resulting knowledge base has been used to establish generic engineering guidelines for the layout of multistage circuits. The potential improvements in separation efficiency that may be realized through the application of these guidelines have been demonstrated using a simple case study.

Jan 1, 2004

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017