Search Documents

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982

By J. M. Keane

Critical to successful dump and heap leaching for copper is an adequate testing program for evaluation of the applicable parameters. This paper deals with testing methods to establish best conditions for dump and heap leaching of copper so that commercial operations can proceed on a rational basis. Discussion is also offered of ore occurrences suitable for dump and heap leaching.

Jan 1, 1985

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By C. C. Huang

Rare earth compounds, such as samarium-cobalt compounds and neodymium-icon compounds, are being used more often for the manufacture of permanent magnets, because these materials permit the production of permanent magnets with higher magnetic energy potential than the conventional ferrite magnets. Especially, the recent rapid developments in the field of electronics and electro-technology have demanded an increased production of rare earth magnets. Unlike ferrite, which is typically produced by a wet process, rare earths can be ground and classified either in a wet or dry process. In the past, batch ball mills, through-pass ball mills in circuit with air classifiers, and conventional jet mills were primarily employed for the dry processing. These methods, however, have suffered from the problems, for example, wear and contamination, low product quality In particle size distribution, difficult to adopt inert-gas operation, and high specific energy consumption. In this report, dry processing of rare earth powders will be presented, especially ultrafine grinding with fluidized bed jet mill.

Jan 1, 1993

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By William H. Hamilton

INTRODUCTION It was not very many years ago that tunneling machine manufacturers spent considerable time trying to convince contractors and mine operators of the advantages of mechanical tunnel boring over conventional drill and blast methods. Today there are few doubters left. There is universal agreement that, not only are tunneling machines here to stay, but the ratio of bored rock tunnels to blasted rock tunnels is increasing at an accelerated pace, and within the next twenty years I predict almost all tunnels will be bored by machine. I believe we are today at a very important mile-post in the development of tunnel boring systems. Felix Gaye stated in his recent article (1) "It is important to disseminate between the efficiency of cutting tools and the overall efficiency of the boring operation". Mechanized tunnel boring in the past placed almost total emphasis on the rock cutting and boring ability of the tunneling machine. With advancements in technology and better solutions to the problems of rock fracture, steering control, and structural design, the emphasis today can be placed on the total-system concept. Tunneling machine design, as one of the key elements in the overall system, presents many problems that are not totally solved today. These design problems are, in the most part, not related with rock fracture, but rather with criteria associated with the over-all operation.

Jan 1, 1997

By J. R. Sims

Gold assays from production blastholes in the Mercur Hill Pit were used to delineate known ore zones and to determine how well previous exploration drilling defined these zones. The most important factors causing inadequate ore zone definition were: 1) inappropriate location of drill holes relative to the ore zones, 2) presence of stopes from previous mining, 3) sampling and assaying errors, and 4) smoothing of the ore zone boundaries during ore reserve estimation. Infill drilling strategies were evaluated to determine the efficiency with which a given drill pattern defined the known ore zones. A drilling strategy was developed which improved ore zone delineation when compared to techniques which maintained uniform drill spacing.

Jan 1, 1992

By David M. Mchaina, Michel Grenier, Stephen G. Hardcastle

An airborne dust survey was conducted at the Arthur W. White mine of Dickenson Mines Limited by CANMET/MRL and Dickenson Mines Limited Staff in April 1990 for the purpose of evaluating environmental conditions underground and in the surface mining plants. The survey was designed to measure respirable silica, total arsenic and lead concentrations at several workplaces. In addition, settled dust and rock samples were collected from workplaces and analysed for total arsenic content. More importantly, arsenic exposure data were needed to evaluate the impact of Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. A total of 165 area and personal air filter samples were collected during the study. Of these, 85, 67 and 13 samples were for arsenic, silica and lead respectively. Sampling aid analyses were performed according to the Ontario Ministry of Labour Regulations. More than 90% of the workplaces sampled for respirable silica, total arsenic and lead were below the Ontario Ministry of Labour Regulations; and 10% of the workplaces sampled for arsenic shaved concentrations above the Threshold Limit value (TLV) proposed in the Ontario Regulation 176/86 as amended by Ontario Regulation 23/87. These results were used to identify occupations and/or workplaces where more sampling and control measures were required respirable silica, total arsenic and lead. This paper describes the results of the dust sampling program conducted at Dickenson Mines Limited.

Jan 1, 1991

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By Edehran Lotfi, Terrence Stobbe

INTRODUCTION Mobile excavating and handling equipment are important 'tools of trade' in the mining and construction industries. The handling of this equipment must be mastered so that its limitations are learned and its harmonic use with other pieces of equipment is practiced. he sudden growth in mobile excavating and handling equipment type, size, complexity, and application started after the Second World War. This growth has not been accompanied by pertinent human factors research. Investigations into the proper and safe handling of such equipment with due regard for human and machine limitations are lacking. One such piece of equipment is the front-end loader (FEL), which during one cycle of operation excavates, loads, and hauls, (Lotfi and Adler, 1981). The diversity of action by FEL is archetypical among excavating and handling equipment. Front-end loaders are the most rapidly proliferating type of equipment in the industry. Also, front-end loaders are involved in the highest number of accidents involving mobile excavating and handling equipment. In the period 1970 to 1978, FEL's were involved in 27% of all mobile equipment accidents in surface mining (Adkins, 1980). Improving operational safety and efficiency will reduce the frequency of accidents. The performance of the operators can be evaluated and improved by the following steps: first, define the operating conditions and the operator workload intensity (Adler and Lotfi, 1983), second, monitor the operator to evaluate his task performance, and third, make recommendations based on the findings. The stressful nature of the equipment operating task is an acknowledged fact (Field, 1980). However, a systematic measurement of stress evaluation is lacking. In this paper, methods for measuring mental stress and fatigue, are defined, the mental load which caused the stress is outlined, and stress measurement methods are proposed. MENTAL STRESS Mental stress has been described as a "specific somatic response to damage or the threat of damage by several environmental agents"

Jan 1, 1986

By Mark W. Springett

The examination of relatively well behaved distributions subject to truncation by a cutoff grade in the mine clearly demonstrates that a bias is inevitably introduced when the selection is based on the results of samples which are subject to even the most idealised error distribution. The idealised error used in this paper is assumed to be normally distributed with a mean of zero and is thus unbiased. The bias introduced can be minimised but it cannot be eradicated. A better understanding of the bias can lead to improved procedures for mine sampling, sample preparation, assaying and estimation of selection units which will not only reduce the discrepancy but more significantly will increase the efficiency of mining selection and hence profitability.

Jan 1, 1989

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By E. Arioglu

Discussion by E. Arioglu Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence [(ASmax)] induced by chain pillar convergence has been related to a parameter (h/1- p) by linear regression. (Notations are expressed in this discussion's Fig. 1 (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goat may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between [ASmax/m vs. h/1-p]. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data. It may be noted here that Wardell's approach (1969) can be successfully utilized for longwall panels having chain pillars. Reference Wardell, K., 1969, "Ground surface and control," Mining Congress Journal, January, pp. 1-7.

Jan 1, 1993

By Y. Okahara

The chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganeus oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were difficult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexitites of the reactions, and the possible mechanisms were discussed. Then three manganiferous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides.

Jan 1, 1969

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By Alan D. Hoagland

The Flat Gap Mine is on Copper Ridge in the Appalachian Valley of East Tennessee, Large zinc orebodies occupy zones of solution and collapse breccias in lower Ordovician Kingsport limestone and dolomite, The principal ore mineral is sphalerite and the principal gangue is dolomite, The orebearing horizons are considerably more than 95% covered by thick residual clay, and geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap Mine, The residual nature of the over-burden at Flat Gap is emphasized, Background heavy metals (mainly zinc) range from 50 to 200 ppm, and the anomalies range to 3000 ppm and more, About 80% to 9W0 of the soil zinc is in relatively insoluble form in solid solution with the hydrous iron oxides and in the crystal lattice of the clay minerals. Quite discrete zones in the soil with sharply contrasting metal value boundaries mark vestiges of bedrock mineralization, and such anomalous soil areas are often contiguous with partially weathered ore. It has not been possible on the basis of chemical criteria to distinguish between an anomaly formed from non-commercial mineralization and one formed from ore.

Jan 1, 1962

By J. N. Economopoulos

The mining industry is becoming increasingly aware of environmental issues and has made big forward steps in the field of environmental management. Legislation, social pressure and competition introduced changes in the industry?s policies and practices in order to conform to the new standards of environmental performance. The paper addresses the need for an integrated and systematic approach to the issues of environmental management within the mining industry.

Jan 1, 2002

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995