Search Documents

By Greg P. Timms, John W. Bennett

Monitoring on Whites waste rock dump at Rum Jungle has provided a unique opportunity to assess the effectiveness of a cover in the medium term. Temperature and oxygen concentration profiles have been measured continuously, from some years before the cover was put in place in 1983 until the present. Lysimeters have been used to measure water infiltration rates. Heat and oxygen transport processes in the dump have been modelled and compared with field data, enabling oxidation rates to be quantified both before and after the cover was put in place. It has been found that the cover reduced the overall oxidation rate to between one third and one half of the uncovered rate. There is evidence that both the overall oxidation rate and water infiltration rate have increased in recent years.

Jan 1, 2000

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By R. S. Das, A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in terms of complexity and value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer-based predictions and practical results. Research conducted to compare computer results with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only if reliable input data are provided.

Jan 1, 1987

By Rilung Xu, Jerry C. Tien, Jian Liu

As underground mines become deeper and ventilation networs more complex, ventilation data becomes more complicated and voluminous, making timely ventilation planning and necessary changes more difficult. Oftentimes, ventilation engineers have to rely on special techques using graphs and schematic maps to carry out necessary ventilation planning [1, 4, 5, 6, 9, 10, 11, 12]. A different graphical method, similar to that reported by Taminago and Isobe [10], has been developed in China [13]. This method uses a two-dimensional diagram drawn from available ventilation survey results. It combines both the customary pressure-quantity diagram and ventilation schematic map, and can greatly expedite the interpretation of survey results, facilitate ventilation system design, short and long-range planning, and emergency planning.

Jan 1, 1993

By Hans von Michaelis

The renaissance in extractive metallurgical practices for gold and silver recovery is far from over. This is one conclusion of a three year investigation into innovations in Cold & Silver Recovery by Randol International Ltd. (1981, 1983). The six volume reference report reviews a host of new processes and innovative applications of older metallurgical practices. Some of these were summarized by von Michaelis (1982, 1982a). There are several reasons to expect this renaissance to continue. One reason is the nature of gold and silver deposits. The list of known occurrences of These metals is very extensive. There are literally tens of thousands of prospects but over 99% of these are too low grade, too small or too refractory for a viable operation employing conventional processing.

Jan 1, 1983

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By Robin Adams

After nearly five years of economic hardship, the world copper industry is, in our opinion, about to enter a period of considerable strength. This opinion is based on three main propositions, namely: 1) there are a number of reasons, both general-economic and industry-specific why copper demand is likely to perform significantly, more strongly in the 1980's than in the 1970's; 2) the virtual cessation of investment in new facilities, especially at the mine level, over the past years makes it physically impossible for capacity to expand as fast as demand in the mid-1980's; and 3) there is much less "excess" inventory available than most analysts believe. If we are correct in these assumptions, then the implication is that copper prices will climb up to, and possibly beyond, the cost-justified price level. Combined with general inflation, this suggests a price in excess of $2/pound by 1985 or roughly treble the 1978 average.

Jan 1, 1979

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By T. Mudder

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

With mine activity dating back to 1792, the Lehigh Valley, about 80 km (50 miles) northeast of the historic Allentown/Bethlehem steel mills and about 160 km (100 miles) northeast of Philadelphia, PA, defined early-day coal mining. Coal mining began just nine years after the end of America?s Revolutionary War. The high-carbon, clean-burning anthracite coal that was hand-dug from the Pennsylvania hills fueled the steam engines that powered the Industrial Revolution, helping build early steam ships and even the first automobiles. Around 1910, at the peak of the U.S.?s early mining effort, there were more than 250,000 men working underground ? 10,000 of them in the Lehigh Valley.

Jan 1, 2012

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

By Alena Johnson

"Much of the copper being produced today uses heap leaching, where pure metal is extracted from the ore with a chemical process rather than smelting. This technique is deployed extensively in major copper producing areas including Chile, Peru and the southwestern United States.Copper ore is excavated from the ground, crushed and then spread in uniform layers on a pad. A slow trickle of sulfuric acid is distributed over the pile, where it percolates to the bottom and a collection point. The acid leaches out the copper, along with other minerals, which can be extracted chemically. This process can be used at large sites producing 100 kt/a (110,000 stpy) and greater.Production on a massive scaleProduction at heap-leach sites is continuous and can operate on an enormous scale. The ore is fed into a crusher to break down the large pieces, and then it moves into an agglomerator to capture the fines and create more uniform particles. While in the agglomerator, the ore is mixed with acid for the first time, helping it to bind the fines into larger particles and starting the leaching process. The treated ore moves by conveyors to a stacker designed to spread it uniformly on the pad.The size of the operation comes into perspective by considering a typical pad measures 1.6-km (1-mile) long and 0.8-km (0.5-miles) wide. Working day after day, the stacker creates individual piles or modules on the pad, each 122 x 61 m (400 by 200 ft) and 3 m (10 ft) deep. When one module is filled, it moves across the pad to the next, filling the area in one continuous pile. A completed row of modules spanning the width of the pad is a cell. Once the entire pad is covered, the process begins again laying down another 3-m (10-ft) layer, and it continues until the entire pad reaches its height limit which can be several hundred feet.Once a new module is completed, technicians lay a network of plastic pipes over the surface in a pattern similar to agricultural drip irrigation installations. The diluted sulfuric acid, called raffinate, is pumped through the pipes so it can be distributed over the module, allowing the acid to soak through the ore and leach out copper as it percolates to the bottom. At the same time, approximately 35 to 45 percent of the acid is consumed by dissolving the calcite carrying the metal in the process. The raffinate reaching the bottom is now characterized as pregnant-leach solution (PLS) since it carries the copper the company is seeking to recover."

Jan 10, 2018

By C. Vasilescu

Phytotechnologies use plants to remediate various media impacted with different types of contaminants. These technologies can be implemented either in situ or ex situ. The affected media in which phytotechnologies can be applied include soil, sediments, groundwater and surface water. They are best applied at sites with shallow contamination of organic, nutrient, or metal pollutants that are amenable to one of five treatment options: phytoextraction, phytotrans-formation, rhizosphere, bioremediation, phyto-stabilization or rhizofiltration. Phytoremediation can be used along or, in some cases, in place of mechanical cleanup methods. Phytoremediation can be used to clean up metals, pesticides, solvents, explosives, crude oil, polycyclic aromatic hydrocarbons and landfill leachates.

Jan 1, 2006

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives – HydroStar® 4208, DXG-F7® and Cyquest® N-900 – using a potentiostatic technique. The current–time data obtained at 0.16V versus the SHE were analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A/m2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current–time data from the electrolyte without organic additives, and confirmed by SEM images, indicate progressive nucleation with two-dimensional growth under diffusion control. None of the organic additives studied at a concentration of 2.5 mg/L with 20 mg/L chloride changed the nucleation and growth mechanism, but the additives increased the number and reduced the size of copper nuclei, leading to more uniform coverage of the stainless steel substrate.IntroductionElectrowinning of copper is an important process in the manufacture of high-purity copper metal. Approximately 20 percent of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth and nature of the initial deposit (Sun and O’Keefe, 1992).Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature and copper concentration, small amounts of organic smoothing agents – traditionally, guar products – are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper nodules and lead to improved deposit quality by producing bright, smooth and dense cathodes.Recently, the use of polysaccharides, such as HydroStar 4208 and DXG-F7, and polyacrylamides, such as Cyquest N-900, has been reported in commercial electrowinning tankhouses as replacements for guar (Ashford, Clayton and Sandoval, 2012; Robinson et al., 2013; Sandoval, Morales and Bernu, 2010). However, little information has been published on the effect of these new organic additives, especially regarding the nucleation and growth mechanisms of copper electrodeposits in their presence."

Jan 1, 2016

By Emmanuel J. Voulgaris

The ?Milos Conferences? is an activity of the non-profit organization ?Milos Conference Center - George Eliopoulos?, located on the island of Milos, Greece. The objective of the ?Milos Conferences? is to create the conditions for interaction among different disciplines of academia and industry, and dissemination of the cutting edge between scientific and technological development. The young scientists are our special aim. The governing body of the ?Milos Conferences? is the ?Milos Conferences Council?. The president of the Council is Mrs. Kitty Kyriacopoulos - founder of the ?Milos Conference Center - George Eliopoulos?, and the members are from academia and industry. The planning and the organization of all conferences are carried out by the ?Heliotopos Professional Congress Organizers? in Athens. The venue is always the ?Milos Conference Center - George Eliopoulos? on the island of Milos. The ?Milos Conferences? comprise of different conference series, each devoted to a general subject. This book covers the proceedings of the ?International Conference on Sustainable Development Indicators in the Mineral Industries?, (SDIMI), a conference of the series under the general title ?Restoring the Natural Balance?.

Jan 1, 2003

By Wern-ping Chen

Technical and non-technical challenges exist in each mega infrastructure project. It?s no exception to the first US underground PPP Port of Miami Tunnel (POMT) project in Miami, FL. The POMT will connect two man-made islands, the Dodge and the Watson Islands, under the Biscayne Bay within highly porous limestone formation. Permeability as high as 0.1 cm/sec has been identified. Its 41-ft outside diameter, if constructed, is the largest precast segment lining in the US. Besides its geological and hydro geological challenges and risks, local community influence and impacts have controlled the fate of this project. This paper describes its tender design enhancements and the evolving of its slow advancement in resolving local community issues.

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010