Search Documents

By R. K. Mehta, M. G. Bersch

Characterization of an ore or mill product is routinely performed by time consuming and tedious chemical analyses, sink-float separations, etc. Additionally, these types of tests do not provide data concerning the interrelations and interlocking of the mineral constituents. This paper discusses some of the applications and capabilities of the Minerals and Material Science Research Center at The University of Alabama. Back-scattered electron images of coal, oil shale, complex suldfide, and tantalium ores were acquired using a JEOL 8600 electron microprobe with a NORAN (formerly Tracor Northern] 8500 image analysis system. Methods of analysis and typical results are discussed.

Jan 1, 1992

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By P. F. Mataich

"Why bother with computer control?" This question and others like it have been heard over and over again by those who have tried to convince operating men that there are sound merits to installing a process control computer. At IMC we have done a great deal of thinking and talking about computer control. In the course of these discussions the operating people have asked a number of questions about computer control. These questions and our answers to them make up the main part of this article. Obviously, the answer as to whether or not to go into computer control will be an individual problem conditioned by your company's circumstances. What I hope to do here is raise some questions, give you an idea of our thinking on the subject, and lay out some general guidelines for you to consider.

Jan 1, 1965

By M. Wickham

Design of an open pit backfill requires an understanding of highly varied processes including slope stability, hydrogeology, pit lake chemistry, climate, runoff, and mine waste behavior. Dynamic systems modeling (DSM) provides flexibility to the designers of open pit backfill, allowing them to directly integrate many different physical processes and varying levels of complexity. DSM also provides for the efficient application of uncertainty analysis to define a range of possible results, the sensitivity of the results to uncertainties in model inputs, and the value of additional data. This paper presents the results of an analysis using DSM to evaluate a pit backfill design at an Arizona mine. The objective of the partial backfill was to stabilize an active slope that threatened facilities adjacent to the pit. DSM was used, in part, to develop a pit lake water balance model for evaluating the influence of the backfill on the ability of the pit to maintain passive hydraulic containment of groundwater and surface water inflows and for evaluating costs for various backfill scenarios.

Jan 1, 2001

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By Gilles Recher, Jörg Riechers, Albert Lueghamer

"INTRODUCTIONIn view of a global trend towards urbanization, more and more trunk sewers and combined sewer overflow tunnels (CSO) with medium to large diameters and the corresponding link sewers are currently built and under design. Shielded tunnel boring machines using segmental lining as tunnel support represent an efficient solution for construction of new wastewater and supply tunnels. Especially in the field of sewers, the durability of concrete structures both exposed to any groundwater present on its exterior and to aggressive waste water as well as gases on its interior is a key requirement. Despite thorough research on segmental lining and mechanized tunneling machinery, conventional thermoplastic liners show comparatively minimal progress in terms of practical advancements. This is in contrast with the development of the latest segment embedded high density polyethylene (HDPE) system. Based on experiences achieved, this paper discusses the latest development of an integral protective lining system in respect of material characteristics and its adaptability to both project and customers’ demands. Reviewed performances, as the bondage behavior of the embedded HDPE system at axial stress loads due to acting thrust cylinders during ring build as well as the ability to drain pressurized water behind the embedded membrane, tested at full scale segments, are also presented. The paper is round off by presenting first details of sewer projects endeavoring to utilize this cutting-edge solution for an integral concrete protection, which will be commenced beginning of 2016.CASE HISTORIES ENCOURAGE ADVANCEMENTS Past experience has shown that unprotected concrete surfaces as well as chemical based linings such as coatings, sprayed linings and cured in-place-systems cannot reach the desired life times. Also the fact that in deep tunnel sewer system hardly maintenance is possible, a durable and maintenance free system is required which only can be reached by applying mechanical anchored HDPE (CPL)."

Jan 1, 2016

By S. P. Brown, J. E. Worthington

Increasingly, exploration geology seems to be growing into a practice overly separated from production geology, yet the eventual purpose of exploration is a producing mine. To help in the search for new deposits, exploration "lessons" will be drawn from the papers given at the Fall AIME Applied Geology Symposium. In addition, examples will be re-emphasized to show how early observation of matters now routine to mine work (for example, hydrology, rock mechanics, oxidation state) can help increase the effectiveness of exploration.

Jan 1, 1992

By J. L. Furtney, C. Fairhurst

"Although global mineral resources are considered to be adequate to meet the needs of a rapidly growing world population, the United States is becoming increasingly dependent on imports. This could have implications for both the economy and national security. The US is a country with a strong tradition of leadership in science and technology. Impressive advances in autonomous underground mining systems reduce the adverse effects of heat and humidity in deep mines and focus renewed attention on ground control. Developments in computing power open opportunities to develop improved understanding of the important role of discontinuities (faults and fracture systems) and more effective design of deep excavations. Establishment of mining R&D Centers at leading US research universities, jointly funded by industry and US federal agencies is recommended as an effective step for the nation to remain an influential partner in world mining. INTRODUCTION. “None of the arts is older than agriculture, but that of metals is no less ancient.. . for no mortal man ever tilled a field without implements. If we remove metals from the service of man, all methods of protecting and sustaining health and more carefully preserving the course of life are done away with.” Agricola (1558)i Homo sapiens, generally acknowledged as the species from which modern Man has evolved, is considered to have originated in Swaziland some 100,000-200,000 years ago. Evidence of use of minerals in that region has been dated to earlier than 40,000 BC.ii Today, a large fraction of the elements of the Periodic Table are derived from minerals, and finding new applications in development of innovative technologies. Agricola’s comments are as applicable today as ever.iii Metals such as copper, tin, lead, iron and aluminum were mined and smelted several thousands of years BC. It was not until the Industrial Revolution, started in the latter half of the 17th Century in Northern England, where coal was available as an energy source, and iron as the basis for fabricating machinery, that dramatic change to society began to occur. Human toil was replaced by far more powerful machines. Rural communities migrated to work in factories in urban areas. Rapid transportation over long distances became possible, leading eventually to the world of today. The change spread to other parts of the world, bringing wealth and power. Although now well established in some regions, the Revolution has still to arrive in many other parts of the world. This can be seen in Figure 1, which shows the relative wealth, or ‘Standard of Living’ as measured by the GDP/capita, of regions around the world. Regions such as North America, Europe, and Australasia iv are seen to have the highest standard. Thanks to today’s global communications systems, regions with relatively low GDP/capita are well aware of ‘how others live’ – and eager to emulate them."

Jan 1, 2018

By L. G. Closs

Gold continued to be the primary focus of minerals exploration worldwide during 1995. Other targets, though, included primary diamonds and base metals, especially copper deposits amenable to solvent-extraction/electrowinning (SX/EW) processing. The discovery of nickel, copper and cobalt at Voisey Bay in Labrador, Canada was an unusual surprise. Meanwhile, exploration geochemistry continues to evolve to meet new challenges. The major event in this category during 1995 was the17th International Geochemical Exploration Symposium (IGES) held in Townsville, Queensland, Australia in May. The meeting was sponsored by the Association of Exploration Geochemists, which celebrated its 25thanniversary of service to the mineral industry, and the Economic Geology Research Unit of James Cook University, Townsville.

Jan 1, 1996

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By Lawrence A. Browning

In recent years, there has been a growing realization of the importance of ground water as a national resource and increasing concern that this resource be properly managed and protected from a variety of pervasive practices that endanger it. Aquifers have been adversely affected in every region of the country. In dealing w.ith the underground water program, EPA will have the following objectives: to protect human health, and to protect and conserve an important national resource. In pursuing these objectives, EPA will take economic consequences and other national objectives (e.g., energy) into account. EPA intends to pursue these objectives in full partnership with the States. Generally the States should retain the lead in protecting ground water.

Jan 1, 1978

By R. Schulz, K. King

Concentrating Line 6 just went down again. The control room operator checks the graphic display. Only one piece of equipment shows an alarm. Clicking on the ball mill icon, he discovers the culprit was the low flow lube switch. The flow looks okay now, but it is the third time this week the switch has stopped the line. Maintenance is called, the switch replaced and the line is up running again. Sending the right person to the right spot immediately can save hundreds of hours of downtime every year. This paper discusses the principles behind implementing smart First-Out Fault Detection to dramatically reduce equipment downtime in new, or existing control system architectures. Methodologies are presented to maximize the system benefits, while minimizing development costs. Case histories are presented for a number of successful implementations in mineral processing plants.

Jan 1, 2001

By X. Zhu, L. Chen, R. Guru, M. Peiravi, M. Mohanty, L. Ackah, B. Xu

"The overall goal of this study was to develop a suitable flowsheet to extract rare earth elements (REEs) from coal ash. Only the findings from the first part of this study is being reported at this time. A total of fourteen coal samples of different ranks were examined for REEs concentration. An anthracite coal sample, originating from Pennsylvania having more than 700 ppm (in the coal ash) was selected for the REE extraction tests. The experimental program completed so far included high temperature leaching using nitric acid, followed by the solvent extraction tests. A 4x2x2 experimental design was used to conduct a total of thirty two high temperature leaching tests by varying acid molarity (at 4 levels), solid content (at 2 level) and leaching time (at 2 level). The highest LREE (light REE) recovery of 90% and HREE (heavy REE) recovery of 94% were obtained from the most optimum leaching test condition while maintaining the impurity recovery to the leachate at less than 40%. Solvent extraction experiments were conducted to recover the REE’s from the above leachate solution using a variety of organic extractants including, TBP, Cyanex, D2EHPA and their combinations. D2EHPA was found to be the best extractant during this SX text series providing nearly 99% recovery of REEs. INTRODUCTION The demand for rare earth element and other strategic metals (REM) in the world is rapidly increasing due to their use in a variety of high technology applications. More than 100,000 tons of rare earth oxides (REO) are being used worldwide on an annual basis. However, we have less than 10% of the world reserve of rare earth element (REE) mineral deposits in the US. More than 60% of rare earth oxide (REO) was imported to the US from outside (mostly from China) in the year of 2013. However, China’s institution of export quota has significantly reduced the supply of REMs to the U.S. Hence, new ways of producing REM and/or finding substitutes for those metals for the high-tech applications need to be invented/discovered in a timely manner. Coal Combustion Byproducts (CCBs), which are discarded as waste materials in most cases, are known to contain REEs (in low concentration) that could be extracted using a suitable process flowsheet. This may be a worthwhile route to pursue considering the short supply of REMs and the abundance of coal ash in thousands of ash ponds in the US. On an annual basis, more than 110 million tons of Coal Combustion Byproducts (CCBs) are being produced while satisfying our nation’s need for electricity (ACAA, 2014). However, less than 50% of these CCBs are being successfully used in various applications and the remainder is being dumped as waste materials in the landfills and ash ponds."

Jan 1, 2017

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1% of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By W. Zhang

"Western China has many shallow coal seams. Mining of these shallow seams contributes to environmental deterioration in part due to disruption of groundwater sources. The lowering of the phreatic surface is attributed to the instability of the impermeable rock groups as a result of mining leading to an increase in permeability and drop in phreatic surface. Underground mining with partial backfilling is one of the fundamental methods of controlling the lowering of the water table in sensitive cases. At present, although significant research has been done in shallow seam mining, there has been no research on the laws governing the movement of impermeable rock groups in partial backfill mining using backfill materials of lower strength. this research, conducted in the Yu Shen-fu region of Western China, developed similar material of sand-based paste filling materials, tested the mechanical parameters of similar material of sand-based paste filling materials, researched on long wall partial backfill mining through similar simulation experiments, obtained the development of “upward fractures” and “downward fracture” under different gap-filling widths and body-filling widths and the movement law of impermeable rock groups under different gap-filling widths and body-filling widths. INTRODUCTION Jurassic coalfield is in the North of Shaanxi province in China, located in border areas of the Maowusu Desert and the Loess Plateau, water resources of Jurassic coalfield in the North of Shaanxi province is meager, ecological environment is fragile (Wang, 2010). With the large-scale development of the mining area, permeable fracture zone will directly affect and spread to the aquifer, causing direct damage to water sources, and lead to the dried up of reservoir, river, wellspring which is recharged by the aquifer(Qian, 2003). There are many researches on aquiclude or impermeable rock groups of shallow coal seam in china, but researches are mainly based on the key strata theory characterized by hard rock as skeleton, without considering the flexibility of impermeable rock groups which is important to reduce the cost of control (Huang, 2010). There are some researches on the stability of impermeable rock groups, but the researches are mainly on permeable fracture zone, which is also called the ""upward crack"" (Wang, 2010), ignoring the influence of the ""downward crack"" on the edge of subsidence basin of impermeable rock groups (Huang, 2010). Previous researches showed that pillar-and-room mining can control the rock crack and surface subsidence (Qiu, 2013), but with the loss of coal resources, and existing disaster a threat of a large scale roof falling. Partial backfill mining mainly by eolian sand bring hope to water-preserved-mining (Fan, 2000), successful practice of paste material backfill mining under buildings and water(Song, 2010)showed its feasibility. Through useing the filling materials with low strength, flexibility and small ratio of height to width, eliminated the threat of a large scale of roof falling, the quantity of partial backfill materials relative to full backfilling are little, the price of sand paste backfilling material is low(Huang, 2011), through designing rational parameters of partial backfill mining, we can achieve the purpose of protecting the phreatic. In this paper, based on the similar simulation experiments, researched on development of the ""upward crack"" , ""downward crack"" and subsidence of impermeable rock groups, researching results can provides the rational parameters to partial backfill mining, and can reduce the cost of filling mining."

Jan 1, 2015

By Harold E. Goetzman, Blair R. Benner, Shaolin Zhong, Rodney L. Bleifuss

A commercial high pressure roller press (KHD 90125) was installed at the Coleraine Minerals Research Laboratory for testing in October, 1994. Pilot plant evaluation of the high pressure roller press has shown that it can be used as an alternative to the rod mill for the comminution of taconite. A series of pilot plant tests were run to compare roller press products to rod mill products in a simulated taconite flowsheet using magnet separation and closed circuit ball milling. Further investigation of a hybrid grinding system, roller press crushing followed by ball mill grinding, indicate that the combination may represent the most energy efficient system for taconite processing.

Jan 1, 1998

By L. Hales

Neural networks are a generalized, multivariable non-linear modeling technique that can be used to model mineral processing operations. Neural networks will be described as will their use in modeling column flotation. Optimization of column flotation will be explored and discussed by using the neural network column models.

Jan 1, 1996