Search Documents

By R. Larry Grayson

A menu-driven, linear-programming- based, user friendly computer program was developed to assist mine managers in determining optimal longwall panel dimensions for a given set of operating conditions. A sensitivity analysis must be performed by varying key mining and configurational parameters over an expected, practical range during the optimization process. Results from analysis of a base case mine indicated that no single combination of longwall panel length and face width is optimal for all operating situations. Each mine manager must therefore look closely at his operating situation and determine the proper dimensions to minimize total mining cost.

Jan 1, 1989

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By Michael Cruickshank

Bob Woolsey was born in 1936 in the state of Georgia and grew up to be a man of great integrity, vitality, wisdom and charm, totally neutral on matters of race, gender, and religion. A true Southern Gentleman in every sense of the word. His passing on July 9, 2008, the victim of an automobile collision, left an empty space in the hearts of his family, and his many friends and colleagues throughout the globe. The posthumous award of the Moore Medal of the International Marine Minerals Society, to Dr. J. Robert Woolsey for Excellence in the Development of Marine Minerals, is a well deserved tribute to this man who spent the last 30 years of his professional career heavily involved in research and development of marine minerals on an international basis. He first came to my attention in Burma in 1979 where, as a newly appointed technical advisor to the United Nations Development Program Offshore Exploration for Tin, I had to fill the shoes of an almost legendary figure "Dr. Bob", who accompanied by his wife Maxine had spent the previous two years initiating the program. Bob had planned to completion the construction in Singapore of a unique drilling vessel the RV Sea Drill, a spud anchored, twin-hulled barge, mounted with a Becker Drill, and designed for sampling alluvial tin deposits in the coastal waters of the Mergui Archipelago in the Andaman Sea, off Tenasserim. He had also designed and built, with the help of his side -kick Bruce Jernigan, a barge mounted dressing plant for reducing and concentrating the drill samples. The adventures of Dr. Bob in transporting the equipment to the drilling site in monsoon weather and the transfer of the drill barge from the Malaysian port of Ranong across the strait to Victoria Point in Burma with a mutinous crew will remain in the hearts and minds of his Burmese colleagues for many a long year. On his return to the States he joined, in 1980, the faculty of the University of Mississippi (UM) as assistant Professor of Geology and Geological Engineering. His prior experience in private industry and the United Nations had focused on marine mineral resources and related environmental engineering projects in Africa, South America, the Mediterranean, the South Pacific as well as south east Asia, working with dredges, mining for alluvial tin, gold, diamonds and industrial minerals. He continued to work in the area of marine minerals at UM, making a name for himself as Director of the Mississippi Mineral Resources Institute (MMRI).

Jan 1, 2008

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By P. Somasundaran, Bruno Lartiges

Two different groups of mechanisms have been considered in the past to explain the effects of chemical additives on grinding. While one group of explanations is based upon alterations of surface and mechanical properties of the individual particles, the other group depends mainly on the arrangement of particles and their flow in suspensions. In this paper some of the past work on grinding aids is reviewed and attrition grinding of a commercially important ceramic material, zirconia (stabilized with yttria) with polyaaylic acid as grinding aid, is studied in order to determine the effect of the aid on the ground product itself. It was observed that even though polyaaylic acid did cause a drastic decrease in the viscosity of the pulp, it did not have any major effect on the grinding of zirconia at least up to 2000 ppm and only minor detrimental effect above it. Importantly, complexation by the polymer was found to cause extraction of yttrium into solution with possibly significant changes in the surface chemical composition of the product.

Jan 1, 1992

By K. S. Eric Forssberg, T. V. Subrahmanyam

The present paper deals with the important technological developments in gold processing and where possible, the data is presented in the form of tables. Gold processing methods have evolved to such an extent that low grade and complex ores once considered uneconomic are now becoming viable. Constant efforts are underway to innovate technologies in order to improve the efficiencies and cut down the capital and operating costs. The methods are discussed.

Jan 1, 1988

By A. Mukherjee

This paper presents an analytical technique for prediction of the damaged rock zone (DRZ) around a circular drift subjected to an anisotropic stress field (analytical solution exists only for the case of hydrostatic stress field). The method can readily be adapted to micro or personal computers. Stress concentrations around the drift are calculated at the centers of small rock elements, using the analytical solutions for a hole in an infinite plate. Potential failure of a rock element is assumed to be governed by the Coulomb failure criterion. When the failure condition is exceeded for an element, the excess shear stress is transferred to the neighboring elements. Progressive failure is allowed to occur until convergence is obtained. The final configuration of the damaged rock zone so obtained can be used to assess rock support requirements, as well as modified modulus and permeability of the DRZ.

Jan 1, 1988

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.

By Duk-Won Park

Since geologic anomalies are one of the governing factors of instability of underground openings, it is extremely important to know in advance the locations and extent of these anomalies such as faults and weak zones. At an underground coal mine in the Black Warrior Basin, core drilling was conducted to find a fault in an area where they were planning to locate longwall panels and possibly a shaft. Core logging did not provide sufficient information to delineate the exact location, strike, and dip of the fault. However, a high resolution reflection seismic study successfully solved this problem. This experience proved the seismic exploration technique could be used for premining coal exploration by reducing drilling costs and providing more accurate and detailed information about geologic anomalies.

Jan 1, 1988

By J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated longwall test facility located at the Pittsburgh Research Center. Sound levels were recorded every l.5 m [5 ft] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 dBA attenuation was attained upwind of the headgate drum.

Jan 1, 1997

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

By R. K. Rajamani, R. Verma

In ball milling the rates of breakage vary primarily with the size distribution of powder in the mill. Using an approximate solution to the batch-grinding equation, the acceleration and deceleration of breakage rates of all individual size classes are determined when the grinding environment is varied. Experimental results with limestone and copper ore show time-dependent breakage rates under both dry and wet grinding conditions. The effect of grinding additives on breakage rates is also studied. In general, breakage rates increase for coarse sizes and decrease for fine sizes with an increase in the fines present in the mill. Such variations have strong implications in closed-circuit grinding.

Jan 1, 1992

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By Ch. Apostolaki

Eighty samples from Roman wall paintings from ancient Corinth were studied by means of optical and scanning electron microscopy coupled to an energy dispersive analyzer, X-ray diffraction and image analysis techniques. The goals of the study were the identification of the exact nature of the pigments and the technical features of paint application (binding medium, adherence to plaster, thickness of the pigment layer), which would provide evidence about the painting technique (fresco or secco). The main plaster is calcitic with secondary calcite as a cement binder to the primary calcite grains. All pigments, except Egyptian Blue, were naturally occurring ochres or pigment minerals, such as limonite, goethite, hematite for yellow, brown and red hues, cinnabar for red hues and celadonite for green color. The presence of specific elements such as Ni and Cr or minerals such as olivine, in the yellow, brown and red pigments, gave an indication about the provenance of the original pigments, which seems to be from Cyprus. The black color was represented using charcoal. It seems, finally, that for the pigment application the fresco technique was used, while secco is also apparent.

Jan 1, 2006

By Asa Weber

With continuing pressure from stockholders not only to maintain but to increase mineral revenues, producers have increased plant capacity. Depressed mineral prices have accentuated the trend toward higher production rates to maintain consistent cash flow, and these same trends have promoted the development of large-scale processing equipment. In addition to the need to handle increased throughput, larger flotation equipment can result in decreased capital-equipment and operating costs. The development of larger column and conventional flotation equipment relies, in part, on suitable scale-up procedures. To properly scale-up large flotation cells and columns, certain constraints and design parameters must be taken into consideration, including velocities in the vessel, residence time, solids suspension, and lip loading. This paper will review the design constraints and scale-up criteria for WEMCO® flotation cells. Scale-up criteria are augmented with computational-fluid- dynamics analyses and high-speed imaging techniques, as well as multiple regresesion analysis of in-plant operational data.

Jan 1, 1999

By K. -A. Björkstedt

INTRODUCTION Strassa lies in the central part of Bergslagen, a tradi¬tional mining district, on the eastern side of the Stora Valley at an elevation of about 200 m above sea level. A railway siding runs between the mine and the Stora railway station from which there are railway connections to the shipping port and iron and steel works in Oxelosund, about 224 km away. The distance to the provin¬cial capital Orebro is about 60 km. The climate is typi¬cal for this part of central Sweden and is illustrated by the diagram of monthly precipitation and temperatures for the years 1968-1975 (Fig. 1). HISTORY There is no certain information as to when the Strassa mine was first worked, but it is known from sur¬viving accounts of mine inspectors that there were smelt¬ing works in operation in nearby villages in the 12th century. An example is the Gusselhytta ore smelting works, 10 km south of Strassa, which dates from this period. Around the year 1540 there were two smelting works in Strassa, the Upper Karberg and Lower Karberg works. Ore for these smelters was probably taken from Strassa and from the adjacent Blanka mine. In the year 1624 Strassa is mentioned by the painter Jons Nils Krook in an account of the iron mines in the Linde mining district (Linde Bergslags Jarngruvor). Several mines were listed in the area, the deepest being about 30 m. An impressive power installation is mentioned in 1639, including a piston system of lashed poles for transmit¬ting power from the Stora River to the Strassa fields. Its length was 2670 m. Common ground comprising about 20.2 km2 (5000 acres) of forest was allocated in 1689 for the furtherance of mining operations. Until the beginning of this century only the rich cen¬tral parts of the ore body were mined and these yielded, after handpicking, lump ore suitable for smelter feed. An example of the ore grades from these early times is an analysis of ore from the "Big Mine" (Storgruvan) from the year 1873: 48.5% Fe, 0.008% P, and 0.06% S. This same year a total of about 18 000 t was ex¬tracted from the Strassa mine. OWNERSHIP The mine was owned and run until 1874 by a min¬ing association made up of 119 so-called "bergsman," who were homesteaders often engaged in agriculture and timber-cutting as well. In that year the Strossa Grufvebolag (Mining Co.) was founded. In 1906 it was con¬verted into a joint stock company, the Strossa Gruveaktiebolag. This was acquired in 1907 by Metallurgiska AB for the implementation of Gustav Grondal&apos;s beneficiating and briquetting methods, for which the Strassa ore was well suited. The same year saw the completion of a new ore dressing plant with an annual production of 46 000 t of ore concentrate. In 1911 the mine passed to new hands, and in 1913 it was purchased by an Austrian company. Extensive new installations were made and in 1915 a new dressing and briquetting plant was completed with twice the capacity of the old one. In 1917 the Strassa mine was acquired by Granges. Be¬cause of unfavorable business trends and technical diffi¬culties, mining operations were brought to a close in 1923. Pumping kept the mine free of water until 1933 but it was completely filled ten years later. Up to 1950 the surface buildings and installations remained intact but the large dressing and briquetting plant burned to the ground in that year. Today only the machine shop re¬mains from this earlier period of operation, now housing parts of the Mineral Processing Laboratory. The decision to take up mining operations again was made in 1955 and construction work began the follow¬ing year. Of the old installation, only the "southern shaft" could be used for some development drifting after it had been completed with a new headframe. Other¬wise, all the buildings and installations required for the operations had to be rebuilt. New installations ready by 1960 were office and personnel facilities, a new shaft and headframe, a sorting and concentrating plant, a macadam plant, settling basins, pump stations, and a railway and yard with transport equipment. The instal¬lation was completed with two plants

Jan 1, 1982

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By A. D. Davis

Limestone-based technology for arsenic removal from water is an innovative and promising method. The technology offers the potential for low-cost disposal of a stable waste product after arsenic removal, either in an ordinary landfill or by encapsulation in concrete. Leaching research described in this paper shows that the limestone waste, after encapsulation in concrete, passes the Toxicity Characteristic Leaching Procedure (TCLP) test. Leaching was less than 0.05 mg/L, which is 1/100 of the U.S. EPA?s standard for disposal of arsenic in a landfill. Disposal of arsenic-enriched waste is critical for commercial viability of arsenic-removal technologies. Low-cost disposal gives the limestone-based method an advantage that could help communities meet the new maximum contaminant level of 10 parts per billion for arsenic in drinking water. The ability to recycle the waste material in concrete could add a significant economic benefit, further reducing overall costs.

Jan 1, 2009

By P. Schmieder

"The close vicinity of mining companies to other sites that are used for commercial and residential purposes or to areas under conservation as well as the fact that the people become more and more sensitive to emissions have led to a negative attitude towards mining operations in the neighborhood. It is above all the use of drilling and blasting techniques that give rise to objections, in the course of which demands for more environmentally-friendly production methods have been voiced. It is in this context that production methods without the use of explosives are considered as an option. After all, the use of such production methods is the only alternative for some quarry operators. The question is what are the true benefits of these techniques and what is the relation between a possible improvement of the environmental effects on the one hand and the technological potential as well as the costs on the other. It is intended to assess the mining techniques for solid rock in their entirety. This paper will therefore look at the aspects for assessing mining techniques in the context of their environmental impact and the costs."

Jan 1, 2005