Search Documents

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By Dennis Z. Mraz

Subsidence profiles over Saskatchewan potash mines exhibit forms which cannot be explained by existing subsidence models. The subsidence is affected by bridging of competent rocks. A modification of the theory can explain the observed displacement of subsidence profiles due to bridging. An unusual shallow secondary subsidence trough has been observed extending two to three kilometers outside the primary subsidence. The secondary subsidence is explained as an elastic compression inresponse to a drop in pore water pressure in the vicinity of the caving zone. The concept of pore water pressure may lead to a safe extraction limit for Saskatchewan mines.

Jan 1, 1986

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By C. A. Young

Cyanide is a toxic species that is found predominantly in industrial effluents generated by metallurgical operations. Cyanide's strong affinity for metals makes it favorable as an agent for metal finishing and treatment and as a lixivant for metal leaching, particularly gold. These technologies are environmentally sound but require safeguards to prevent accidental spills. Various methods of cyanide remediation by separation and oxidation, including photolytic advanced-oxidation processes, are therefore reviewed. Reaction mechanisms are presented throughout the paper. The methods are compared in regards to their effectiveness in treating various cyanide species: free cyanide, thiocyanate, weak-acid dissociables, and strong-acid dissociables.

Jan 1, 1996

By L. C. Morales

Mexico has an area of about 2 million km2 (772,260 sq miles), with volcanic activity, large shores and mountainous areas reaching as high as 6000 m (19,680 ft) above sea level. These conditions are favorable for most mineral deposits, some of commercial value and others as a source of mineral samples. In addition to its vast mineral wealth, Mexico has another valuable asset in its people. Even before the discovery of America, natives were successfully mining metals. During the colonial days, the mineral deposits were mined to increase the wealth of Spain. All this experience was passed from generation to generation. It created a tradition of mining and minerals processing engineers that currently accounts for about 182,000 people supported by mining-related activities. Nonmetallic minerals in Mexico have been mined by natives since the early days. They knew the value of kaolin clays for pottery, as evidenced by archeological findings. This experience was also passed from generation to generation and has become recognized worldwide as ceramic wares of high quality. The Talavera ceramic from Puebla is an example of family traditions many generations old.

Jan 1, 1994

By E. Varouchakis

Spartan Spatial Random Fields (SSRF?s) provide a new geostatistical framework (Hristopulos, 2003) with applications targeting environmental risk assessment and natural resources estimation. SSRF?s have the ability to incorporate constraints based on physical laws in the statistical description and have proved to be computationally fast in the analysis of synthetic data sets. This paper presents an application of a specific SSRF model and a new local-error spatial estimator (Hristopulos, 2005) in the mapping of environmental pollutants using a real data set. A detailed comparison of the local SSRF estimator with a classical kriging method is presented. It is shown that the SSRF approach provides a competitive alternative for spatial estimation.

Jan 1, 2005

An AFM has been applied to study in situ the adsorption of oleic acid on fluorite in aqueous solutions. The AFM images show that fluorite surface becomes smoother with the adsorption of 7 × 10-5 M oleic acid solution at pH 9. Force measurement shows that fluorite is strongly positively charged in water at pH 6, suggesting a neglectable surface carbonation of fluorite. The adsorption of oleic acid at pH 9 renders fluorite more and more negatively charged. The surface morphology change of fluorite as shown by the AFM images suggests that oleic acid chemisorbs on fluorite at pH 9. Increasing temperature can help increase the adsorption of oleic acid on fluorite. It may also improve the lateral polymerization of unsaturated oleic acid on fluorite as suggested by the smoother mineral surface in oleic acid solutions at an elevated temperature.

Feb 23, 2014

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By F. C. Bond

History The breaking and shaping of rock was one of man's earliest occupations. In the Paleolithic Age long before the dawn of history, arrow¬smiths and the makers of stone axes, hammers, knives, scrapers, spears, and borers were highly respected members of society. In early historical times stones for building blocks, roads, and city walls were shaped by slaves and convicts, who also did most of the mining. However, great artists erected beautiful stone sculptures, while gifted architects planned imposing temples and monuments. Until well into the 19th century nearly all rock was broken laboriously by hand. The small rock required by John MacAdam for his macadamized roads in England in the 1820s was produced by women and boys seated alongside the roadside with hand hammers and legs wrapped with rags. Eli Whitney Blake, a nephew of the Eli Whitney who invented the cotton gin, developed the first successful jaw crusher before 1870. The gyratory conical crusher soon followed. Comparative tests established its large capacity advantage over the jaw crusher, as well as its greater cost for a given feed size. Both types have been in use for more than 100 years. Crushing rolls appeared before 1900. Thomas A. Edison made very large diameter rolls which were excessively long; they failed because of shaft deflection. Various types of disk crushers and edge runner rolls appeared about this time. The older methods of reducing rock were adaptations of other processes. The stamp battery of dropping weights effected crushing by simulating heavy hammer blows; the much earlier arrastre, in which heavy stones were dragged in a circular path over the ore by animal power, came from the prehistoric method of grinding grain between two rubbing stones, while the jaw crusher was adapted from simple squeezing devices. But the tumbling grinding mill was not just an adaptation; it was an invention, because it required thinking on a somewhat higher order-there was no prototype. Its nearest antecedents were probably the small closed tumbling drums used in England more than a century ago for cleaning and polishing small iron castings. The date of the first tumbling mill actually used to grind rock is unknown, but it was later than the American Civil War (1861¬1865). It was almost certainly a closed or batch mill in which rock was placed and rotated until it reached the desired particle size. It could have been operated either wet or dry. The first published refer¬ence to such a batch mill was one introduced by Alsing in England (1870) for the grinding of calcined flints for pottery work.21 There are several rather indefinite reports of grinding mills in the early 1890s, including an overflow ball mill in the Helena and Livingstone reduction plant in Montana which may have been the first of its kind. 11 Many of the first mills, which were called tube mills, used hard rock both as grinding media and as mill lining. The rock used was preferably stone from the Normandy and Danish beaches, when it could be imported. This remarkable siliceous stone was already widely used for grist mills throughout America, and its resistance to wear was greatly respected. The decade of the 1890s saw the development of tumbling mills with continuous feed and discharge and their extension into different industrial uses. By 1895 some experience had been accumulated. Iron grinding balls were being tested and the proper speed of rotation was being determined. The Clark Patent tube mill was featured in an E. P. Allis bulletin of 1890, which may have been the first published description of a tube mill. More than 1,000 Gates tube mills had been built by Allis-Chalmers before 1913. Many of these were used in gold mining, espe¬cially in South Africa. The 5 x 22-ft size was particularly favored for grinding portland cement; the use of tumbling mills in the manufac¬ture of cement began about 1900. A great deal of attention was paid to the mill lining. Metal was then relatively expensive, and the general approach was to trap some of the rock grinding media into mill lining pockets. This rock would then absorb the wear and protect the metal lining. In the first ten years of the 20th century there were several different types of pocketed liners, with different manufacturers advancing the superior claims of their patented arrangements. The Osborne liner, developed in South Africa, was probably the most successful. 21 Another item which attracted much attention was size classifica¬tion within the mill and in ancillary equipment attached to the mill and rotating with it. The Krupp type, with interior screens protected inside the mill lining, was developed quite early in Germany, possibly before 1890. The Dorr reciprocating rake classifier (1907) had not yet been invented, and many strange and impractical screening and classifying devices were proposed. In these unsatisfactory machines the two separate processes of size reduction and classification were combined into one operation. It was many years before recognition came that a machine is most efficient when it is designed for one specific purpose. There was much industrial wastage before the opera¬tions of grinding and classification were finally separated. After 1900 the grinding of portland cement raw material and of cement clinker required large numbers of tumbling mills. Most of the raw material was then ground dry. This was also the heyday of gold mining. The old stamp mills that were used in great numbers for grinding gold ore did not grind sufficiently fine to liberate all of the gold, and the new tube mills were installed following the stamps. After 1910 larger diameter tum¬bling mills with larger grinding media were developed. These could receive the finely crushed ore directly, and the inefficient stamp batter¬ies were gradually eliminated. The Rand in South Africa was the greatest gold producer, treating immense quantities of rather low-grade but consistently free milling gold ore. The first tumbling mills, or tube mills, went into operation there in 1904. They were so successful that within a few years no new stamp batteries were installed in the district, even though old ones continued to pound away until after 1950.3 The early tube mills on the Rand all employed Normandy or Danish pebbles, which had to be imported at considerable expense. Their reported wear was as low as 4 lb per ton ground. 4 Many of the mills were lined with the same tough Danish stone cemented into place, while others used the pocketed steel Osborne liner. It was in 1907 on the Rand that an important test was made using hard native ore for grinding media in place of the expensive imported pebbles. 3 This ore, called banket, did not wear as well as the renowned Danish pebbles, but the cost per ton of grinding was definitely reduced. Many of the tube mills on the Rand were soon grinding with native ore. This was the beginning of the development now called autogenous grinding, in which the ore grinds itself. This is treated under a separate heading. See Subsection 3C, Chapter 4. Gold mining was important in America also, and its grinding history follows that of the Rand. Danish pebbles were replaced by native ore in Santa Gertrudis, Mexico, in 1913, 4 and in Consolidated Gold Fields, Nevada, in 1914. 5 Other properties followed suit. However, it gradually became apparent that the capacity of a given mill could be almost doubled if rock grinding media were re¬placed by cast iron or steel grinding balls. In order to increase plant grinding capacity many rock media mills were converted to iron grind¬ing media in the second decade of the present century. In some mills the motor size was doubled; other mills were cut in two and another motor was provided for the second half. Grinding mills began to assume a more modern appearance. Crushing rolls were formerly much used following crushing in jaw or gyratory crushers and preceding grinding in ball mills. How¬ever, the roll surfaces wore rapidly, and skilled maintenance was required to obtain even wear. Rod mills could take feed of the same crusher product size and reduce it finer. The first rod mill was con¬structed by Mine and Smelter Supply Co. and was tested in Canada

Jan 1, 1985

By Ashraf A. M. A. Wali

Many of the economic resources of Egypt have been recognized and exploited for thousands of years (e.g. gold and copper). Most of these minerals, particularly those from hard-rock sited deposits, are found in complex form along with other components while those present in sedimentary sequences are largely in simple compounds or as native elements. Recognition of their characteristic settings (structure, basin development, environment of formation etc.) is the main clue in predicting and locating their presence. The main economic minerals exploited in Egypt today come from sedimentary sequences and include sodium and potassium chlorides, gypsum, sulfur, and sedimentary iron ores. Large amounts of low grade sedimentary phosphates are known but are not of economic value at today's prices. Recent intensive investigation in the north-eastern Sinai (EI Arish) and along the southern coasts of the Gulf of Suez has revealed new and extensive sulfur and chloride deposits, and considerable oil and gas are now being exploited from closely related sediments. Tin is the only mineral that is produced from hard-rock sources, and gold and copper deposits are present but not of high enough grade to be economically viable. However, a significant part of Egypt has not yet been studied in enough detail to close the door on future discoveries. Another point of considerable geological interest is the presence of diverse, modern evaporitic settings, from which we may draw the analogs for many of the older gypsum, anhydrite, chloride and sulfur de-posits. In fact these analogs are so well displayed that both the Sinai and Gulf of Suez-Red Sea evaporites (Middle and Upper Miocene) can be readily compared with these modern deposits.

Jan 1, 1990

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002

By H. Habenicht, E. Urschitz

Three mining methods for full extraction in flat coal seams - i.e., longwall (L W), shortwall (SW), and rib pillar extraction (RPE) - are com- pared with each other in view of the introduction of a mechanized, self-advancing roof support. Features are shown according to which RPE appears most attractive under certain conditions. In this presentation, the mining methods are outlined and discussed. The new support (Alpine Breaker Line Support, ABLS) is described, and its employment is explained. A trial operation in RPE using the ABLS has been conducted successfully in a South African coal mine. The results and improvements are stated.

Jan 1, 1988

By S. Kittel, P. Galleguillos, H. E. Urtubia

The rougher flotation at Escondida consists of 80 cells of 100 m3 each, with injected air. Escondida has developed a system of automatic control of the rougher flotation using video cameras, which have been operating since 1997 for remote monitoring and manual control. Since 1999, an image processing software and a group of rules have allowed implementation of an expert system. To date, the expert system controls the superficial speed of each cell by adjusting the air flow and the froth depth of the flotation bank. Preliminary tests of the expert control on two of the eight rows gave 1.2% higher rougher recovery at a 92% degree of confidence. The proven benefits are already sufficient to move towards a complete plant implementation.

Jan 1, 2001

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

By P. Maraboutis

Extractive industry (mining and quarrying operations), as other industrial activities, is subject to environment protection laws, regulation and standards such as the Environmental Impact Assessment directive, Natura 2000, Habitats & Birds directive, Water Framework directive etc The European Commission (EC) is aim to strengthen the EU environmental legislation to improve the (environmental and human) safety of mining activities. The mineral processing and the management of the mining waste will be covered by the new amendment of the Seveso II Directive, by a Best Available Techniques reference document (BREF) describing the Best Available Techniques of mining waste management and a new directive on the mining waste management. At the same time initiatives as the environmental liability, the energy taxation for environmental reasons and the natural resources management policy, which will have a positive impact on the protection of the environment, will affect the extractive industry operation procedures.

Jan 1, 2002

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986