Search Documents

By Graham G. W. Mustoe

Energy losses are important factors in a conveyor's performance and design. A significant energy loss due to belt sag within a conveyor system occurs when shearing motion between the bulk material particles occurs as the material moves along the belt. An initial analysis of these phenomena was performed using the discrete element method, which is a general-purpose numerical modeling technique for analyzing the mechanical behavior of particulate materials. The software used in this work was Overland Conveyor Company's, Chute Analyst Professional, a discrete element computer code designed specifically for analyzing bulk materials transportation and handling problems.

Jan 1, 2008

By S. Park

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing less hydrophobic particles to drop off. A bubble-coarsening model has been developed by calculating the changes in Plateau border area as a function of the initial bubble size at the base of a foam, liquid fraction, and foam height and then relating the predicted Plateau border area to the critical rupture thickness of lamellae film. The model predicts that bubble coarsens with increasing froth height, decreasing frother dosage, and decreasing aeration rate. The model predictions are in good agreement with actual bubble size measurements.

Feb 23, 2014

By R. S. Saunders

Congress, under the Nuclear Waste Policy Act of 1982, as amended, charged the U.S. Department of Energy (DOE) with the responsibility for safe and permanent disposal of high-level radioactive waste in a geologic repository. The waste will consist of spent fuel from commercial nuclear generating plants and reprocessing activities. Under direction of this law DOE is currently evaluating Yucca Mountain in Southern Nevada as the candidate site for a potential high-level radioactive waste repository. Presidential, Congressional and State of Nevada approval are needed for repository construction to proceed after successful completion of site characterization and recommendation of the site to Congress. The DOE will submit a license application to the Nuclear Regulatory Commission (NRC) to construct the geologic repository. Following successful construction DOE will update its license application to operate the repository.

Jan 1, 1993

By Gunnar Nord

Shifting ground conditions when tunnelling often call for different methods of attacking the tunnel face. In order to overcome problems with local unstable soft ground in a hard rock tunnelling project the Boodex method offers a cost effective alternative. Boodex and variants of it is a combination of two well-known techniques, drilling with Boomer rig using Odex gear. It will give a steel lined hole ready for grouting and the steel pipe has a load bearing capacity that means that a spiling effect is achieved. In this paper the method and some applications will be described with possibilities and limitations.

Jan 1, 2003

By Matthias Rheinlander

The paper will describe Virtual Design and Construction (VDC) as a tool which will enable us to build a project ?virtually? on a computer before constructing and operating it in the real world. VDC computer models are built, using information from various sources including survey, 3D laser scanning, CAD and GIS to represent the project and its components in a coordinated and consolidated infrastructure model. This model is reviewed and evaluated by, and shared among project teams including owners, con-tractors, designers, engineers, construction managers, stakeholders and operators. It allows teams to fix costly design and construction issues before construction on site. Benefits and lessons learned from global projects will be discussed

By W. K. Hitchcock

Hydrogen is regarded as being a high temperature indicator of spontaneous combustion. It is currently used in underground coal mines to detect advanced heating?s. Previous work has mostly consisted of small scale tests with high air flow to mass ratios. A large-scale test rig has been used to investigate the gas indicators of coal self-heating. In particular, the relationship of gas evolution, the location of its evolution and the temperature at which it is evolved has been examined. It has been found that there are two distinct zones of hydrogen production: one at the hot spot and the other in an oxygen deficient moist zone downstream from the hot spot which is at a relatively low temperature of approximately 100°C. This has implications for the interpretation of mine atmospheres.

Jan 1, 2009

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation's first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By Dilip K. Sinha

In the paper some interesting cases of applications of Operations Research and Computer Methods as worked out by the author and accepted by the management of some of the newly formed Indian mining organisation for implementation are highlighted. The main emphasis on the application cases was to use simple techniques and methods which yield the result in shorter time period, The case problems mainly deals with the production system optimisation in unit mines, areas/divisions and at the corporate levels. Also the management decisions regarding reorganisation of transport and distribution system of material and mineral are attempted to be optimised. Further, the case of management system development with computer aided decision making worked out for single large Iron Ore Project captive to a steel plant is outlined. Finally, the case of a large mining company having decentralised units and divisions geographically dispersed throughout the country, computerised management decision-information system designed on the basis of inputs and outputs of decision models relevant for different levels of management in the organisation is depicted.

Jan 1, 1986

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

By M. P. Meehan

The purpose of this paper is to present the Anamax Instrumentation Department's: responsibilities, organization, preventive maintenance, test facilities, training and applications. The Anamax Mining Company is a general partnership between AMAX Arizona, Inc. (a subsidiary of AMAX INC.) and The Anaconda Company (a subsidiary of Atlantic Richfield). Anamax's product and by-products include: copper, molybdenum, and silver; uranium is to be added as a by-product in early 1980.

Jan 1, 1980

By T. Panhorst

Evaluation of through-deck blasthole sample reliability at the Lone Tree gold mine revealed a non-systematic bias in the sampling system. Ore is primarily hosted within the Powerline fault zone. Clay gouge, present in the fault zone and typically enriched in gold content, forms agglomerates during blasthole drilling leading to a segregation error during sampling. Replicated samples split from blasthole cuttings piles show through-deck samples to be either significantly enriched or depleted by 1.5 standard deviations or more from the mean gold content of their respective cuttings pile quality of through-deck samples correlates strongly with quantity of clay present.

Jan 1, 1999

By August V. Castelli

Drilling fluids have changed over the years from water and/or water frequently mixed with local clays to scientifically com- pounded materials (mud). This change has occurred due to changes in drilling methods from percussion to rotary: depth maximum from 21 m in the first oil well to more than 9 000 m; and variety in types of well or hole to gas, oil, water, and mineral exploration. Environmental concerns about the composition of the fluid as to heavy metals and oil on the cuttings has recently caused changes in the materials used in the mud. The drilling fluid should perform the following functions (Darley et al., 1980): 1) Carry cuttings from beneath the bit, transport them up the annulus, and permit their separation at the surface. 2) Cool and clean the bit. 3) Reduce friction between the drilling string and the sides of the hole. 4) Maintain the stability of uncased sections of the borehole. 5) Prevent the inflow of fluids-oil, gas, or water-from permeable rocks penetrated. 6) Form a thin, low-permeability filter cake which seals pores and other openings in formations penetrated by the bit. In addition to these, the fluid should: 1) Not injure drilling personnel nor be damaging or offensive to the environment. 2) Not require unusual or expensive methods of completion of the drilled hole. 3) Not interfere with the normal productivity of the fluid- bearing formation. 4) Not corrode or cause excessive wear of drilling equipment. A number of industrial minerals, chemicals, and other materials are used as additives in the drilling fluid to accomplish these functions. Industrial minerals make up the highest percentage of the additives in a drilling fluid. Drilling fluids are classified according to their principal components: water, oil, and gas. If the major component is either water or oil, the component along with the suspension of solids, cuttings and additives is referred to in the trade as a mud. The largest use of some industrial minerals, such as barite and bentonite, is in drilling muds. For other materials, such as gypsum and limestone, drilling usage is only a small percentage of total demand. RAW MATERIALS [Table 1] lists the industrial minerals used in drilling fluids, their form, specifications, and uses. Each raw material will be discussed as to its mineralogy, physical and chemical properties, and the location of major deposits with respect to drilling fluids. Attapulgite Attapulgite is a crystalline hydrated magnesium silicate clay mineral, prized for its viscosity in saline waters. The particles are needle-like rather than the platelets common to most clay minerals. The specific gravity is 2.5 and the Mohs hardness is 1 to 1.5. Attapulgite is one of the materials sometimes referred to as fuller's earth. The major producing areas in the United States are southern Georgia and northwestern Florida. It also is mined in Spain, Senegal, the Republic of South Africa, Turkey, India, and Australia. Barite Barite is crystalline barium sulfate. It has a high specific gravity for a non-metallic mineral, 4.5 when pure, and is used as a weighting agent. Generally, the specific gravity ranges from 4.20 to 4.35. It is relatively soft with a Mohs hardness of 3 to 3.5 and is not very abrasive. Barite is inert, non-toxic, and clean to handle. Common contaminants are quartz, iron minerals, gypsum, and calcium carbonate. If there is considerable gypsum in the barite, it will thicken the mud. The major deposits in the United States are in north central Nevada, near Battle Mountain. The major producing countries, other than the United States, are China, India, Mexico, the former USSR, Turkey, and Morocco. The major deposits in India and Nevada, and some in China, are stratiform, commonly quite pure bodies in bedded sedimentary rocks.

Jan 1, 1994

The minerals industry contributes to the economic growth, prosperity and quality of life of nations, particularly in areas where there might be limited opportunities for employment in other sectors. However, notwithstanding their economic importance, the minerals extraction and processing industries are considered to have significant impacts on the surrounding environment. In recent years many mines have implemented modern monitoring technology and modelling of the monitored environmental parameters to provide scientifically proven indicators about the state of the environment. The flexibility required by the minerals industry to respond dynamically to a changing natural, social and economic environment has become a major consideration. Whilst the notion of continuous improvement is embodied within most environmental management systems, what is now required is a structured audit trail which tracks the flow of resources through the production process to the ultimate environmental impact associated with their consumption, transformation and disposal. Imperial College is coordinating an EC funded project, which is developing a methodology to minimise the ?full life-cycle? impact of metalliferous mining projects, adopting an integrated approach to production and process design, and the costs involved. In order to develop a life cycle assessment (LCA) system that will incorporate different types of data related to the minerals extraction operations, a data inventory was designed and coded in an object-relational database model. The calculation procedures accounting for the input/output balance of the alternative scenarios for mining production, processing, waste disposal, monitoring, and their financial implications are being programmed into a software system. This paper presents the rational and innovative aspects of this work. The methodology developed for the life cycle database is illustrated for the mining production and gaseous emissions components of the system.

Jan 1, 2003

Everyone knows the importance of careful handling of explosives. Even so, the point is on occasion all too graphically driven home. Witness the recent blast at a Utah explosives plant that killed five people. Part three of this series on explosives discusses transportation, storage, handling, and destruction. Federal, state, and sometimes local regulations govern the many steps involved in transporting, storing, and handling explosive materials. Regulations minimize personnel exposure to hazardous material and insure that the explosives remain stable and usable.

Jan 9, 1981

By Thomas V. Durkin

About 1.41 kt (45.2 million oz) of gold have been ! produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection. Mining is promoted as an industry while prevention of pollution is required along with reclamation of affected lands to a beneficial use. The South Dakota Department of Environment and Natural Resources' (DENR) system of "one-stop shop- ping" for environmental permits streamlines the permit process. It fosters quick resolutions to compliance problems and helps keep enforcement actions out of the courts. Paha Sapa means "Hills that are Black" in Dakota Sioux. Appearing dark from a distance due to a thick forest of Ponderosa pine, the Black Hills were gold to many people. The exact date that gold was discovered in the Black Hills remains debatable. An inscribed stone tablet found in 1887 near Spearfish recorded these words:

Jan 1, 1998

By M. Balakrishnan, K. A. Natarajan, J. M. Modak, J. S. Gururaj Naik

The ability of various fungal species isolated from gold mines to uptake gold and base metals such as zinc, copper, iron and lead from gold-process cyanide effluents was investigated. Under identical treatment conditions, different strains showed wide variations in their ability to take up gold and other base metals. Aspergillus terreus exhibited as high as a 60% gold uptake. Almost complete removal of zinc was possible with various fungi and with the yeast Saccharomyces cerevisiae. Studies at various metal concentrations showed a higher gold uptake from dilute solutions, and studies with Aspergillus niger showed that gold uptake by living cells increased gradually as the contact time increased. Metal uptake capacities between living and nonliving cells were also compared. A waste biomass (ABM- I), obtained from a fermentation industry, wasalso identified as having a high gold uptake capacity. At 5% (W/v) solids, ABM-I could efficiently remove up to 83% of the gold contained in an effluent solution within 24 hrs.

Jan 1, 1995

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By B. J. Scheiner

The Bureau of Mines has developed a system for dewatering waste slurries by flocculating mineral particles with polyethylene oxide (PEO) and dewatering the resulting flocs on static and/or rotary screens. This paper discusses data obtained from dewatering, rheology, and ion-exchange experiments. A possible mechanism is postulated for the attachment of PEO to claylike particles through a water bridge with the intershell waters of the exchanged ion and the polymer.

Jan 1, 1986

By Richard R. Klimpel

INTRODUCTION Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Froth flotation is a physico-chemical process for separating finely ground minerals from their associated gangue material. The process involves chemical treatment of a finely divided (ground) ore in a water pulp to create conditions favorable for the attachment of certain of the mineral particles to air bubbles. The air bubbles then carry the selected minerals, called valuable, to the surface of the pulp to form a stabilized froth which is removed and recovered. The unattached gangue material remains submerged in the pulp and is either discarded or reprocessed. To obtain the adherence of the desired mineral particles to the air bubbles, at least two specific steps must occur: a hydrophobic (water hating) surface film must be formed on the particles to be floated along with a hydrophillic (water wetting) film on all other particles; and a controlled bubble surface tension interface must be maintained, allowing for high particlelbubble collision frequency and efficient attachment or sticking of the particle to the bubble once collision has taken place. In most flotation applications, the above two steps are controlled by chemical flotation reagents. The collector is a chemical reagent which produces the hydrophobic film on the valuable mineral particle and is the primary driving force that initiates the flotation process. The frother is a chemical reagent which influences the collision frequency and attachment efficiency of hydrophobic particles and air bubbles. Thousands of research papers and books have been published on the chemical theory behind sulfide mineral collectors, e.g., Fuerstenau (1962), Fuerstenau (1976), Fuerstenau, et. al. (1985), King (1982), Leja (1982) and Moudgil and Somasundaran (1987), This article will only address and summarize some of the more practical aspects of collector usage. The industrial scale practice of froth flotation in sulfide mineral concentration has changed little since the 1950's. For example, of the approximately 80,000 metric tons of sulfide mineral collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago. A very interesting and informative history of collector development has been given by Crozier (1984). In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920's with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years. As a result of the above environment which makes reagent cost/performance analysis difficult for new reagents, there is a strong tendency for the flotation operation to use, and reagent companies to supply, as cheap as possible raw materials and manufactured products that are quite general in application. In the last 20 years or so, there has been increasing technical effort to tailor make reagents for specific applications, but to date such work has had little commercial impact. It is clearly the hope of this author and others that this situation will change in future years as technology improves and pressure for improved flotation performance intensifies. This article is a condensation of collector usage trends quantified as part of a comprehensive industrially oriented applications program on froth flotation organized by Klimpel and coworkers (1979-1987) and as reported in various countries that participated in the program from 1978-1983. No attempt will be made to provide specific.

Jan 1, 1986