Search Documents

By J. E. Gray

Before specifications are discussed it may be well to define the term "Mineral Aggregates." Professor K. B. Woods (1) defined "Mineral Aggregate--An aggregation of sand, gravel, crushed stone, slag, or other material of mineral composition used in combination with a binding medium to form bituminous and portland cement concrete, macadam, mastic, mortar, plaster, etc., or alone as in railroad ballast, filter beds, and various manufacturing processes, such as fluxing, etc. " This definition is too all inclusive for the purposes of this paper; therefore, this discussion will be confined to specifications for natural aggregates which means sand and gravel and crushed stone, and limited primarily to coarse aggregate which is aggregate larger than one-quarter inch in size. To the uninitiated, this may seem to be a very limited subject on an unimportant material. However, aggregates are essential in all types of construction. The tonnage and value of these two aggregates produced in the United States during 1959 as reported by the Bureau of Mines were as follows: Sand and Gravel 729,895,000 tons valued at $728,527,000 Crushed stone 581,721,000 tons valued at $824,411,000

Jan 1, 1961

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner's bonanza. I do not mean to' infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

By Fred Pena

The VERTIMILL has proven itself to be a reliable performer in heavy duty industrial applications. Applications have been extensively used in the mining industry, flue gas desulfurization applications, and industrial minerals field. The machine is a vertically stirred machine that utilizes a screw operating in a grinding media. Grinding media types have ranged from several sizes of steel balls as the most common to pebbles or ceramic media. Mesh-of-grind and final product size are the determining criterion for the selection of the media size used. Product size consists have ranged from very coarse to super-fine grinds of less than 25 microns. Savings in consumption of power, grinding media, and liners when compared to a conventional ball mills, have been realized. Savings in consumption of reagents have also been demonstrated.

Jan 1, 1992

By C. J. Webb

Column experiments were performed to determine the ability of Madison aquifer material to adsorb arsenic and other constituents in a heavily mined watershed of the Black Hills in western South Dakota. The Madison aquifer is a karstic dolomite and limestone reservoir that is exposed on the flanks of the Black Hills. Streams that cross the Madison in the eastern Black Hills typically lose all their flow to the aquifer at sinkholes. In this work, Madison aquifer material was obtained for loading of six-inch diameter columns, which were backfilled with Madison aquifer water. Stream water then was allowed to displace the aquifer water during column testing in order to simulate mixing of the two waters at sinkholes and to determined adsorption of arsenic and other dissolved constituents. Initial results show that some adsorption of arsenic occurred when compared to more conservative tracers such as nitrate.

Jan 1, 1999

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

Two key strategies for a new generation of mining are developing domestic raw material production and doing so in an environmentally responsible way, according to presenters at the 83rd annual meeting of the SME Minnesota Section in Duluth (the 71st annual University of Minnesota Mining Symposium). From technical sessions detailing how to build com-munity support, to a short course on international perspectives in iron ore mining and processing, the two-day meeting emphasized the potential of Minnesota state deposits and the importance of maintaining productive community relations both locally and globally. The meeting of more than 300 mining industry professionals began on April 20 with a traditional convocation celebrating the values of northern Minnesota. The accompanying tradeshow, with a record 131 booths, showed the speed and vigor of the economic rebound. Keynote speaker Scott Anderson, vice president and senior economist at Wells Fargo, stated the prevailing mood of the conference: ?Wow, what a difference a year makes.? With metal prices and sales up and heading higher, he said, it was clear that the production-centered economic recovery is reaching the mining and the minerals industry. However, Anderson sounded a few notes of caution. Serious threats to economic stability remain, including the burgeoning national de?cit, high unemployment and the still out-of-control foreclosure crisis. Overall, he predicted a below-average recovery and stressed the importance of developing a long-term business strategy.

Jul 1, 2010

By R. J. Heath

Potassium, together with nitrogen and phosphorous, is one of the essential nutrients required for growth. All living things need potash and so the major demand for potash (approximately 95% of, total demand) is as a fertilizer. Traditional agricultural techniques relied on the return of organic materials to the soil to provide nutrient requirements and maintain soil fertility, and the prevailing low crop yields required little in the way of added fertilizers. But agricultural productivity has increased dramatically in recent times, and this increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows that there will always be a demand for potash. There is no substitute. Other fertilizers that contain N and P are complementary and not competing products.

Jan 1, 1987

By T. V. Falkie

REMARKS OF DR. THOMAS V. FALKIE, DIRECTOR, BUREAU OF MINES, U.S. DEPARTMENT OF THE INTERIOR, BEFORE THE FALL MEETING OF THE SOCIETY OF MINING ENGINEERS, AIME, ACAPULCO, MEXICO, SEPTEMBER 23, 1974 This is a time of uncertainty on the world mineral scene. For some of the world's so-called "developed" countries, reserves and production of key minerals are running low. And, we have learned that the energy so essential in recovering and processing minerals can suddenly be in short supply. The prospects for a "no growth" situation in energy or mineral consumption are practically nil. Moreover, the world's economy is in flux, casting doubt on whether traditional mineral customers will continue to be able to buy, or for that matter, whether traditional suppliers of minerals will continue to sell. It is clear that the mineral situation is contributing to world inflationary pressures, which incidentally are most damaging to developing countries. So it is appropriate that SME members devote this session to the world mineral situation, and consider some of the opportunities and responsibilities that we will inevitably encounter as the future becomes the present. The opportunities, to me at least, are especially intriguing, I have the good fortune to be part of an organization that has an enormous capability and responsibility for dealing with mineral problems. The Interior Department's Bureaus, including the Bureau of Mines, have been around for a long time. They are. a prolific and reliable source of both mineral information and mineral technology.

Jan 1, 1974

By F. Wendling, R. C. Nascimento, S. S. Wendling

"The objective of this research is to study the quality of blast-furnace iron ore pellets with binary basicity 1 fired on a pilot scale using the two main firing processes that are presently in use in the world and comparing them. Currently, the great majority of pellet producers use the traveling grate process because of its higher production capacity. In this study, the physical and chemical qualities of the pellet feed, limestone, anthracite and bentonite were determined and the amount of additives for a blast furnace pellet with the defined basicity was calculated. The physical properties of the green and dried pellets were determined accordingly. Produced pellets, after being fired on a pilot scale using traveling grate and grate kiln, were subjected to chemical analysis and physical testing. No significant difference was observed in the metallurgical quality — that is, reducibility index (RI), reducing disintegration index (RDI) and swelling index (SWI) — of the pellets produced by both processes. However, a comparison of cold physical tests — tumble and cold compression strength — shows improved quality of the pellets fired using the grate kiln process.IntroductionThe development of human civilization owes much to iron and steel (Sun et al., 2015). Iron is the most used metal in the world, and it is the main component of steel, which is present in materials for structural engineering, automotive and general industrial applications (Liu et al., 2014). Increased global demand has led to a decrease in the resources of ore with high iron content (Zhang et al., 2015), and currently 95 percent of the iron ore in China needs processing before smelting as its iron (Fe) content is only about 30 percent on average (Liu et al., 2014).Pelletizing is a process to economically agglomerate iron ore pellet feed into pellet form. After balling, green pellets are conveyed to the final step of the manufacturing process (Pena, 1982). The process is a multifaceted one, involving high temperatures, air flow gas turbulence and complex equipment geometry (Larsson et al., 2009). The pellets are fed into blast furnaces, which are now predominantly used in the extraction of iron. Ore processing also requires physical separation, including crushing, grinding and water removal (Sun et al., 2015).The increase in steel consumption favors the exploitation of low-concentration ores and the production of pellets (Halt and Kawatra, 2014). Pellet quality is affected by various factors, such as their physical and chemical characteristics and their temperatures and residence times in the furnace (Halt, Silva and Kawatra, 2015). Different geological settings lead to a wide range of different minerals (Graça et al., 2015).This work aims to generate important information for the pellet industry in the area of physical and metallurgical qualities of the agglomerates obtained by two processes: traveling grate and grate kiln."

Jan 1, 2017

By J. G. Smith

Of the variables affecting the electrical properties of coal measure rocks, water content is by far the most important, This paper describes specially developed apparatus and methods of measuring electrical conductivity and permittivity at constant humidity conditions. Electrical properties variations were measured for Applachian and Illinois, U.S.A. coal 2 basin samples in the frequency range 2 X 10 to 2 X 10 Hz. Coal measure rock electrical behavior, when correlated with mechanical behavior, is potentially useful in a number of mining applications.

Jan 1, 1985

By W. P. Stroud, R. S. Dennen

A ground penetrating synthetic pulse radar system has been used by the US Bureau of Mines to probe into a coal pillar to locate hidden structures or anomalies. Direct matrix inversion was used to obtain a velocity image of the interior of the pillar. The reconstructed image showed the existence and location of a relatively low velocity material within the pillar. Core samples were taken from the pillar in a region surrounding the low velocity material. Analysis of the cores showed the presence of a clay vein coinciding with the low velocity material imaged in the tomogram.

Jan 1, 1992

By I. A. Molodkina, A. V. Kurkov, V. V. Shatalov

New compound classes previously unknown in flotation practice of non-sulphide ore beneficiation have been developed. The presented study results consider amine salts of alkyl sulphate and alkyl benzene sulphonic acid used as primary collectors, N-methyl amides of alkyl phosphoric acids - as auxiliary modifying collectors and pentaerythritole ethers of tall oil - as flotation accelerators. These reagents synthesized from accessible raw material are almost ready for commercial production. Efficiency of the new reagents for various non-sulphide ores has been demonstrated in a series of flotation tests.

Jan 1, 1995

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By Wayne E. Kilker, Michael J. McBride, William P. Levy, Thomas J. Lamb

Between 1989 and 2004 the Massachusetts Water Resources Authority (MWRA)constructed several major wastewater and water tunnels associated with three major projects in the Boston area of eastern Massachusetts. There were many similarities and differences in the bedrock conditions encountered and among the contractual approaches for these independent projects. Through a clarification of the approach similarities and analysis of the contract differences, this paper addresses and presents what are considered to be valuable lessons learned. In doing so, the paper follows the evolution of such disparate issues as contract conditions, baseline reports and dispute review boards. The authors believe that the lessons learned even represent what, in certain cases, could be referred to as “universal truths” that are intended to have application to the next generation of tunneling contracts.

Jan 1, 2005

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

By R. E. Miller

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By J. P. Allen

Cobalt, nickel, and manganese can be recovered quickly, cleanly, and selectively from cobalt-rich manganese crust by leaching in dilute acid solutions in the presence of hydrogen peroxide. Common selective precipitation methods can then be used to recover these metals from the leach liquor. The leaching reaction produces only oxygen as a byproduct, and the waste residue from leaching was tested and found to be non-hazardous under existing EPA specifications. The leaching process is effective in either fresh water or seawater. This research is a part of the Bureau of Mines program to identify the mineral resources of the Exclusive Economic Zone and devise methods for recovering their valuable components.

Jan 1, 1990